Résumé du contenu de la page N° 1
Résumé du contenu de la page N° 2
TANDBERG COMPASS MXP / UTILITY MXP Trademarks and Copyright All rights reserved. This document contains information that is proprietary to TANDBERG. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form, or by any means, electronically, mechanically, by photocopying, or otherwise, without the prior written permission of TANDBERG. Nationally and internationally recognized trademarks and trade names are the property of their respective
Résumé du contenu de la page N° 3
Environmental Issues TANDBERG visual communication products significantly reduce the need for travel and thereby help reduce various types of pollution. TANDBERG recommends the use of low energy peripherals, such as EnergyStar™ monitors. Thank you for buying a TANDBERG product. Battery handling The batteries for the Remote Control are Long Life Alkaline batteries, which means you will need fewer batteries, further benefiting the environment. Please follow the guidelines on th
Résumé du contenu de la page N° 4
TANDBERG COMPASS MXP / UTILITY MXP Operator Safety Summary For your protection, please read these safety instructions completely before operating the equipment and keep this manual for future reference. The information in this summary is intended for operators. Carefully observe all warnings, precautions and instructions both on the apparatus and in the operating instructions. Warnings Water and moisture - Do not operate the equipment under or near water - for example near
Résumé du contenu de la page N° 5
Contact us If you have any questions, comments or suggestions, please see the Online Support service at www.tandberg.net. It is also possible to send a fax or mail to the attention of: Product and Sales Support TANDBERG P.O. Box 92 1325 Lysaker Norway Tel: +47 67 125 125 Fax: +47 67 125 234 v
Résumé du contenu de la page N° 6
TANDBERG COMPASS MXP / UTILITY MXP Table of Contents 1 Introduction............................................................................................................................... 1 1.1 At a Glance ............................................................................................................................ 3 1.2 Menu Structure ...................................................................................................................... 5 2 Installation
Résumé du contenu de la page N° 7
4.1.8 Screen Settings........................................................................................................ 66 4.1.9 Software Options ..................................................................................................... 71 4.1.10 Date and Time Settings ........................................................................................... 72 4.1.11 Max Call Length ..........................................................................................
Résumé du contenu de la page N° 8
TANDBERG COMPASS MXP / UTILITY MXP viii
Résumé du contenu de la page N° 9
1 Introduction 1 Introduction The TANDBERG Compass MXP provides essential video features for face to face communication in public areas with the quality and reliability found in all TANDBERG equipment. The TANDBERG Utility MXP provides essential video features for face to face communication in rugged environments with the quality and reliability found in all TANDBERG equipment. Audio Quality High-performance audio provides a richer, more complete visual communication experie
Résumé du contenu de la page N° 10
TANDBERG COMPASS MXP / UTILITY MXP NEW H.460, ITU Standardized firewall traversal, support NEW High security network authentication (802.1x) The TANDBERG videoconferencing system can also be used purely as an audio-bridge (with an ISDN connection). Presentations The Natural Presenter Package (NPP), makes it possible to receive presentations and comprises: TF Digital Clarity which provides presentations of exceptionally high quality resolution video. Users can disp
Résumé du contenu de la page N° 11
1 Introduction 1.1 At a Glance Camera The camera is an integrated part of the unit and is centrally placed just above the monitor. On the Utility MXP it is possible to close the camera (for privacy) by sliding Utility MXP across a door. Monitor The Digital LCD displays the far-end videoconferencing site in addition to the menu. Codec The codec is the heart of the system. Its main task is the compression of outgoing video, audio and data, the transmission
Résumé du contenu de la page N° 12
TANDBERG COMPASS MXP / UTILITY MXP far end. The power output of the lamp can be varied upon installation (or by service personnel thereafter), and can be adjusted from zero to full power. Remote Control The remote control is only delivered with the TANDBERG Utility MXP. The remote control is located inside the locked cabinet on the Utility MXP, and is intended for system setup when using ISDN. The reception of the remote control signal is limited to a small hole directly under th
Résumé du contenu de la page N° 13
1 Introduction 1.2 Menu Structure The menu structure is divided in three. The Kiosk Menu, which is available for all users when Kiosk mode is activated, the Main Menu, which contains all functionality of the system and the Administrator Menu that contains all the settings of the system. The menu structure for Kiosk Menu is shown below. Figure 1-2. Kiosk menu. 5
Résumé du contenu de la page N° 14
TANDBERG COMPASS MXP / UTILITY MXP The Main Menu and Administrator Settings are only accessible when Kiosk Menu is deactivated. Select Control Panel and Administrator Settings from the Main Menu. Making changes to the Administrator Settings will change the behavior of the system. The menu structure for Main Menu and Administrator Settings is shown below. Figure 1-3. Main menu. 6
Résumé du contenu de la page N° 15
1 Introduction Figure 1-4. Administrator Settings menu. Note that the system features and menu settings may vary depending on network selection and software package. 7
Résumé du contenu de la page N° 16
TANDBERG COMPASS MXP / UTILITY MXP 2 Installation Precautions: Never install communication wiring during a lightning storm. Never install jacks for communication cables in wet locations unless the jack is specifically designed for wet locations. Never touch uninstalled communication wires or terminals unless the telephone line has been disconnected at the network interface. Use caution when installing or modifying communication lines. Avoid using communication eq
Résumé du contenu de la page N° 17
2 Installation 2.1 Unpacking The TANDBERG Compass MXP and Utility MXP consist of the following items: Videoconferencing system with built-in camera, handset and lamp Remote Control (Utility MXP only) Batteries User Manual on CD Integrated power supply Cables High security keys 9
Résumé du contenu de la page N° 18
TANDBERG COMPASS MXP / UTILITY MXP 2.2 Connecting Cables 1. Power cable Connect the power cable from the wallplate to the power supply. Note: The connection of main electrical supply to the wallplate is described in the Installation Sheet. 2. ISDN cables Connect the ISDN cables to the ISDN connectors on the system. Connect the ISDN cables to the ISDN sockets (S/T- interface) provided by the service provider. Your main number will be the number associated
Résumé du contenu de la page N° 19
2 Installation 2.3 Monitor Configuration Power on Switch the system on by connecting the power cable from the wallplate to the integrated power supply. After the system has performed a self-test routine, the main menu will be displayed on the monitor of the Utility MXP (units are shipped with Kiosk Mode OFF). The Compass MXP is shipped with Kiosk Mode ON, and the monitor will therefore display the Kiosk Menu. 11
Résumé du contenu de la page N° 20
TANDBERG COMPASS MXP / UTILITY MXP 2.4 System Configuration The Compass MXP and Utility MXP have default settings from the factory enabling initial use. However the system must be configured for each installation. Configuration settings can be made via the system menu using the remote control, or more easily via telnet or web interface using IP. The following screen pictures are based on remote control access directly on the system, whilst the telnet or web interface gives a differen
