Instruction d'utilisation Magenta MULTIVIEW 250A

Résumé du contenu de la page N° 1

MultiView

250A


Receiver

Quick Reference

&

Setup Guide

















Magenta Research
Magenta Research
934 Federal Road, Brookfield, CT 06804 USA
934 Federal Road, Brookfield, CT 06804 USA
(203) 740-0592 FAX (203) 740-0596
(203) 740-0592 FAX (203) 740-0596
www.magenta-research.com
www.magenta-research.com

Résumé du contenu de la page N° 2

FCC/IC RFI STATEMENTS, EU DECLARATION OF CONFORMITY . FEDERAL COMMUNICATIONS COMMISSION Contents AND Chapter Page INDUSTRY CANADA RADIO FREQUENCY INTERFERENCE STATEMENTS 1. Specifications...................................................................................................3 2. Introduction ........................................….............................

Résumé du contenu de la page N° 3

CHAPTER 1: Specifications . 1.Specifications 2. Introduction 2.1 Overview Cable Required: Category 5, 5e, 6 shielded or unshielded twisted pair Compliance: CE; FCC Class A, IC Class/class A Magenta’s MultiView™ CAT5 Video System MultiView series extends VGA and audio signals over ordinary Category 5 cable. Video Support: to UXGA (1600x1200 @ 70Hz), RGBHV, RGB, Composite, S- Video, Component Video modes This manual covers the Magenta MultiView™ 250A

Résumé du contenu de la page N° 4

CHAPTER 3: SETUP & INSTALLATION . 3. Setup and Installation 3.2.2 CONNECTIONS ON THE SINGLE-PORT VGA/AUDIO TRANSMITTER 3.1 Cabling Considerations The single-port units with audio support video and audio signals over CAT5 cable. The audio signal is line-level audio, and powered speakers are required. Figure 3-1 • We recommend mounting and connecting all cabling to the MultiView™ Series shows the MultiView™ Series UTx transmitter with Audio Transmitter connections, components b

Résumé du contenu de la page N° 5

CHAPTER 3: Setup and Installation . 3.2.3 CONNECTIONS ON THE VGA/AUDIO MULTIVIEW T4 TRANSMITTERS 3.2.5 A TYPICAL MULTIVIEW T4 TRANSMITTER–RECEIVER APPLICATION Figure 3-5 shows an application in which a MultiView™ Series T4 Transmitter is The MultiView T4 four-port transmitter is used when linked to four MultiView™ Series Receivers. the same signal is distributed to multiple display devices. You set it up and cable it the same as you would with the single-port transmitter.

Résumé du contenu de la page N° 6

CHAPTER 3: Setup and Installation . 3.3 Configuration Settings 4. Troubleshooting The MultiView™ 250A receiver is configurable for various video and audio modes. Note that a compatible transmitter unit must be used at the source end. Reference the appropriate transmitter 4.1 Common Problems user guide or call for technical assistance. A dipswitch on the receiver unit is used to set the video and audio configuration mode. Table 3-1 In most cases, nearly every issue with the MultiView

Résumé du contenu de la page N° 7

APPENDIX A: Cabling Pinouts . Appendix A. Cabling Pinouts Appendix A. Cabling Pinouts Table A-2. T568B CAT5 pinout Table A-1. HD15 video connector. Pin RGBHV RGBS RGsB Com- SVHS YUV Composite (VGA) posite (Y/C) Video & Stereo Audio 1 Red + Red + Red + C+ V+ Audio Left 2 Green+ Green+ Green+ C+ Y+ Y+ C+ 3 Blue+ Blue+ Blue+ U+ Audio Left 4 — — — 5 Gnd Gnd Gnd 6 Red- Red- Red- C- V- Shield 7 Green- Green- Green- C-