Résumé du contenu de la page N° 1
MP-XP7220KR,MP-XP5220KR
SERVICE MANUAL
Mobile mini note PC
02 200 G103 04
MP-XP7220KR,MP-XP5220KR
Area Suffix
KR ------------------ Korea
TABLE OF CONTENTS
1 SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
1.1 Disassembly procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
1.2 Preinstallation procedure . . . . . . . . . .
Résumé du contenu de la page N° 2
MP-XP7220KR,MP-XP5220KR SECTION 1 SPECIFIC SERVICE INSTRUCTIONS 1.1 Disassembly procedure 1.1.2 Removing the keyboard assembly (See Figure 2 ~ Figure 4) 1.1.1 Removing the internal battery (1) Push the three latches (a) in the upper part of the keyboard (See Figure 1) with a single-slotted screwdriver or a flat screwdriver, and Prior to performing the following procedure, remove the external lift the keyboard. battery. (2) Disconnect the wires from connectors CN4 and CN1 on the (1) Remove one
Résumé du contenu de la page N° 3
MP-XP7220KR,MP-XP5220KR 1.1.3 Removing the top case and LCD panel assembly (See Figure 1 and Figure 5 ~ Figure 8) • Prior to performing the following procedure, remove the key- board assembly. (1) Insert a single-slotted screwdriver or a flat screwdriver in a H Hinge cover inge cover space b on the underside of the hinge cover. Then, remove the hinge cover by pulling the screwdriver in the direction indicated by the arrow. And then, remove one more hinge cover at the other side of the main body.
Résumé du contenu de la page N° 4
MP-XP7220KR,MP-XP5220KR 1.1.4 Removing the mother board Microphone and (See Figure 9 ~ Figure 11) headphone jack • Prior to performing the following procedure, remove the key- board assembly, the top case, and the LCD panel assembly. Mother board (1) Remove one screw F (short), one screw G (middle), and the two screws H (long) attaching the mother board. (*In attaching the mother board, tighten H , H , G, and F 1 2 Battery detector in this order.) 2 2 switch (2) Lift the mother board while
Résumé du contenu de la page N° 5
MP-XP7220KR,MP-XP5220KR 1.1.5 Removing the parts on the mother board (See Figure 12 ~ 15) • Prior to performing the following procedure, remove the moth- er board. *Removing the fan assembly (1) Remove the four screws I attaching the fan assembly. (2) Disconnect the connector wire from the connector CN13 on the mother board. *Removing the hard disc drive (1) Remove one screw J at the side of the mother board where the hard disc drive is not attached. (2) Remove the hard disc drive by moving the
Résumé du contenu de la page N° 6
MP-XP7220KR,MP-XP5220KR 1.1.6 Removing the top case and the LCD panel assembly Rubber pad and screw O (See Figure 16) • Prior to the following procedure, remove the top case and the Latch LCD panel assembly from the bottom case. (1) Remove the two screws N attaching the hinge. (2) Remove the tapes fixing the two wires of the LCD panel as- sembly if necessary. NN Hinge Tape Tape Hinge LCD LCD Latch Latch Latch Fig.16 1.1.7 Removing the LCD panel Fig.17 (See Figure 17 and Figure 18) • Prior to th
Résumé du contenu de la page N° 7
MP-XP7220KR,MP-XP5220KR 1.2 Preinstallation procedure No data including Windows XP has been recorded in service parts HDD. It is necessary to put data in HDD after HDD is replaced. < The following materials are needed > *CD-ROM drive (model name MP-CDX1E) *CD for installing HD Image (a set of five CDs) (1) Connect CD-ROM drive (model name MP-CDX1E) and the Mobile Mini Note PC by using PC card slot. (2) Insert the 1st CD for installing HD Image in CD-ROM drive. (3) Push a power supply
Résumé du contenu de la page N° 8
MP-XP7220KR,MP-XP5220KR 1.3 Caution in exchanging a bottom case 1.3.1 As for COA LABEL Neither "LE40888-001A/COA LABEL PRO" nor "LE40888-002A/COA LABEL HOME" can be reused. COA LABEL is also necessary in exchanging a bottom case. 1.3.2 As for serial label "Serial label" where model name and serial number are written is not dealt with as service parts. Please reuse it. Please remove a label with exfoliation agent: Parts number -- UN-001 Parts name ----- SUBSIDIALY MATERIAL *How to remove a label
Résumé du contenu de la page N° 9
MP-XP7220KR,MP-XP5220KR 1.5 Operation check item list after the repair is completed Item Contents Required equipment 1 IEEE1394 Is connected with IEEE1394 port the Digital video camera and Digital video camera made of our company. do recognize it? 2 SD CARD Is connected with SD card slot the SD card and do recognize it? SD card on the market. 3 PC CARD Check whether PC card operates properly when it is connected PC card corresponding to Card Bus on the to PC card slot for Card Bus. market. Check
Résumé du contenu de la page N° 10
MP-XP7220KR,MP-XP5220KR VICTOR COMPANY OF JAPAN, LIMITED AV & MULTIMEDIA COMPANY MOBILE IT CATEGORY 1644, Shimotsuruma, Yamato, Kanagawa 242-8514, Japan (No.G1004) Printed in Japan 200302WPC
