Résumé du contenu de la page N° 1
User’s Manual
YCV 100
S-Video Encoder
VYC 100N and VYC 100P
Composite Video Decoder
Extron USA - West Extron USA - East Extron EMEA Extron Asia Extron Japan Extron China Extron Middle East
Headquarters
+800.633.9876 +800.3987.6673 +800.7339.8766 +81.3.3511.7655 +400.883.1568 +971.4.2991800
Inside USA / Canada Only Inside Europe Only Inside Asia Only Inside China Only
+800.633.9876 +81.3.3511.7656 FAX +971.4.2991880 FAX
68-779-01 Rev. C
Inside USA / Canada Only
+1.919.863.1794 +31.33.453.4040 +6
Résumé du contenu de la page N° 2
Precautions Safety Instructions � English Warning Extron’s Warranty Power sources � This equipment should be operated only from the power source This symbol is intended to alert the user of important indicated on the product. This equipment is intended to be used with a main power operating and maintenance (servicing) instructions in system with a grounded (neutral) conductor. The third (grounding) pin is a safety Extron Electronics warrants this product against defects in materials and wo
Résumé du contenu de la page N° 3
FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communicati
Résumé du contenu de la page N° 4
Table of Contents Chapter 1 • Introduction .......................................................... 1-1 About the YCV 100, VYC 100N, and VYC 100P ........ 1-2 Features ...................................................................................... 1-2 Chapter 2 � Installation and Operation .......................... 2-1 Mounting the YCV 100, VYC 100N and VYC 100P .2-2 Tabletop use ........................................................................... 2-2 UL rack mounting guidelines
Résumé du contenu de la page N° 5
Table of Contents, cont’d YCV 100, VYC 100N, and VYC 100P Chapter One 1 Introduction About the YCV 100, VYC 100N and VYC 100P Features ii YCV 100, VYC 100N, VYC 100P � Table of Contents
Résumé du contenu de la page N° 6
Introduction About the YCV 100, VYC 100N, and VYC 100P YCV 100, VYC 100N, and VYC 100P The Extron YCV 100 is a high-performance S-video to composite video encoder. It combines S-video Y and C (luminance and chrominance) signals into a composite video signal. The encoder is compatible with NTSC 3.58, NTSC 4.43, PAL, and SECAM signals. The unit accepts S-video input on two female BNC connectors or one 4-pin mini DIN connector and outputs composite video on one female BNC connector. The Extron V
Résumé du contenu de la page N° 7
DISTRIBUTION AMPLIFIER Installation and Operation Rack mounting Mounting the YCV 100, VYC 100N, & VYC 100P For optional rack mounting, do not install the rubber feet. The YCV 100, VYCN, and VYC 100P can be set on a table or ™ mounted on a rack shelf, under a desk or tabletop, or on a Mount the YCV 100, VYC 100N, or YCV 100P, on a VersaTools rack shelf (RSF 123, Extron part #60-190-20; RSB 123, projector mount. part #60-604-21), or on a 6" deep rack shelf (RSU 126, part #60-190-10; RSB 126, part
Résumé du contenu de la page N° 8
MAV SERIES INPUTS OUTPUTS AV MATRIX SWITCHER 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 ENTER PRESET I/O IR VID +dB AUD -dB AUDIO SETUP IPA T IPA IPA T IPA DISTRIBUTION AMPLIFIER MDA SERIES DISTRIBUTION AMPLIFIER Installation and Operation 2. Mount the unit on the rack using the two included rack screws. It can be vertically mounted facing in either direction, as shown here. Mounting the YCV 100, VYC 100N, and VYC 100P on a 1U standard rack shelf Back of the rack installation The YCV 100, VYC 100N, and VYC
Résumé du contenu de la page N° 9
Installation and Operation, cont’d Projector mounting Rear Panel Features and Cabling Projector mount the YCV 100, VYC 100N, or VYC 100P using the YCV 100 optional PMK 100 mounting kit (part #70-217-01) as follows: VIDEO OUT YCV 100 1. Remove rubber feet if they were previously installed on the S-VIDEO ENCODER 2 bottom of the unit. Y POWER C 2. Attach the projector mounting brackets to the unit with the 3 machine screws provided. 12V OR 0.1A MAX S-VIDEO IN 3. Secure the unit below the ceiling to
Résumé du contenu de la page N° 10
Installation and Operation, cont’d Strip the insulation from the wires to expose 5 mm (3/16") of the conductors. Do not tin the stripped power supply leads before installing the captive screw Smooth connector. Tinned wires are not as secure in the captive Ridges screw connectors and could be pulled out. The two power cord wires must be kept separate SECTION A–A while the power supply is plugged in. Remove Power Supply Tie Wrap power before wiring. Output Cord To verify the polarity before co
Résumé du contenu de la page N° 11
Installation and Operation, cont’d Troubleshooting YCV 100, VYC 100N, and VYC 100P Possible problems and their solutions include the following: � Problem: No power at unit Solution: Verify that the unit is receiving power by checking the front or rear LED. If no LED is lit, check the DC power plug termination and polarity. � Problem: No video input Solution: Verify that the source and output devices are powered on and connected properly. � Problem: Some chroma crawl on the vertical edges or a r
Résumé du contenu de la page N° 12
Specifications, Part Numbers, and Accessories VYC 100N ......................... NTSC 3.58 Video VYC 100P .......................... PAL Gain ................................................ Unity YCV 100 ............................ NTSC 3.58, NTSC 4.43, PAL, SECAM Bandwidth YCV 100 ............................ 8 MHz (-3 dB) General VYC 100N, VYC 100P ..... 5.5 MHz (-5.5 dB) External power supply ................ 100 VAC to 240 VAC, 50/60 Hz, external, autoswitchable; to 12 VDC, 1 A (max.), Vid
Résumé du contenu de la page N° 13
Specifications, Part Numbers, Accessories, cont’d Included Parts These items are included in each order for a YCV 100, VYC 100N, or VYC 100P: Replacement Included parts part number YCV 100 60-559-01 orVYC 100N 60-558-02 or VYC 100P 60-558-03 12 VDC, 1 A external power supply 70-055-01 IEC power cord 3.5 mm, 2-pole captive screw connector Tweeker (small screwdriver) User’s Manual Optional Accessories These items can be ordered separately: Accessories Part number Mini under-desk mounting bracket 7
