Résumé du contenu de la page N° 1
USER
MANUAL
MODEL 2150
CopperLINK™
Ethernet Extender
This is a Class A device and is not intended for
use in a residential environment.
Part# 07M2150-UM SALES OFFICE
Rev. B
(301) 975-1000
Revised 8/31/10
TECHNICAL SUPPORT
(301) 975-1007
An ISO-9001Certified
Company
Résumé du contenu de la page N° 2
CONTENTS 1.0 Warranty Information ................................................................. 4 1.1 Regulatory Information ................................................................. 4 EMC Directive:.............................................................................. 4 Low-Voltage Direcive (Safety):..................................................... 4 PSTN:........................................................................................... 4 1.2 Radio and TV Interf
Résumé du contenu de la page N° 3
D Distance Chart, Based on 24 AWG (0.5 MM) .......................... 19 3
Résumé du contenu de la page N° 4
1.0 WARRANTY INFORMATION Patton Electronics warrants all Model 2150 components to be free from defects, and will—at our option—repair or replace the product should it fail within one year from the first date of the shipment. This warranty is limited to defects in workmanship or materials, and does not cover customer damage, abuse or unauthorized modification. If this product fails or does not performs as warranted, your sole recourse shall be repair or replacement as described above. Under
Résumé du contenu de la page N° 5
tion. The device has been tested and found to comply with the limits for a Class A computing device in accordance with specifications in Subpart B of Part 15 of FCC rules, which are designed to provide reasonable pro- tection from such interference in a commercial installation. However, there is no guarantee that interference will not occur in a particular instal- lation. If the device does cause interference to radio or television recep- tion, which can be determined by disconnecting the uni
Résumé du contenu de la page N° 6
1.6 SAFETY WHEN WORKING WITH ELECTRICITY • This device contains no user serviceable parts. This device can only be repaired by qualified service per- sonnel. • Do not open the device when the power cord is con- nected. For systems without a power switch and without an external power adapter, line voltages are present within the device when the power cord is connected. • For devices with an external power adapter, the power adapter shall be a listed Limited Power Source. The mains outlet
Résumé du contenu de la page N° 7
In accordance with the requirements of council direc- tive 2002/96/EC on Waste of Electrical and Electronic Equipment (WEEE), ensure that at end-of-life you sepa- rate this product from other waste and scrap and deliver to the WEEE collection system in your country for recy- cling. This device contains no user serviceable parts. This device can only be repaired by qualified service per- sonnel. WARNING This device is NOT intended nor approved for connec- tion to the PSTN. It is intended only
Résumé du contenu de la page N° 8
2.0 GENERAL INFORMATION Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and is warranted for one year for parts and labor. If any questions or problems arise during installation or use of this product, contact Patton Electronics Technical Support at +1 (301) 975-1007. 2.1 FEATURES Variable rate CopperLINK extender - Easy to configure Auto-MDIX Ethernet Configurable 10/100, Full/Half, and Auto-Negotiating Ethernet
Résumé du contenu de la page N° 9
Figure 1. Typical application The pair of 2150 models work together to create a transparent extension between two peered Ethernet LANs. Figure 1 shows a typical point-to- point application. 3.0 INSTALLATION The Interconnecting cables shall be acceptable for external use and shall be rated for the proper applica- tion with respect to voltage, current, anticipated tem- CAUTION perature, flammability, and mechanical serviceability. To install the 2150 Ethernet Extender, do the following: 1. C
Résumé du contenu de la page N° 10
Power jack CopperLINK twisted-pair RJ-45 interface Dual 10/100 Ethernet ports Figure 2. Model 2150 standalone rear panel 3.1 CONNECTING THE TWISTED-PAIR LINE INTERFACE The Interconnecting cables shall be acceptable for external use and shall be rated for the proper applica- tion with respect to voltage, current, anticipated tem- CAUTION perature, flammability, and mechanical serviceability. The Model 2150 supports communication between two peer Ethernet LAN sites over a distance of up to 5,00
Résumé du contenu de la page N° 11
1. To function properly, the two Model 2150s must be connected together using twisted-pair, unconditioned, dry, metal wire, between 19 (0.9mm) and 26 AWG (0.4mm). Leased circuits that run through signal equalization equipment are not acceptable. 2. The Model 2150 is equipped with an RJ-45 interface jack that can be used on the CopperLINK interface. The CopperLINK interface is a two-wire interface. Observe the signal/pin relationships on the Model 2150's CopperLINK interface jack. Th
Résumé du contenu de la page N° 12
1 TX+/RX+ 2 TX-/RX- 1 2 3 RX+/TX+ 3 4 (no connection) 4 5 5 (no connection) 6 6 RX-/TX- 7 7 (no connection) 8 8 (no connection) Figure 4. Model 2150 10/100Base-T RJ-45 Connector Pinout. 3.3 CONNECTING POWER The Interconnecting cables shall be acceptable for external use and shall be rated for the proper applica- tion with respect to voltage, current, anticipated tem- CAUTION perature, flammability, and mechanical serviceability. The Model 2150 does not have a power switch, so it powers up as s
Résumé du contenu de la page N° 13
CopperLINK™ High Speed Ethernet Extender Power Link Ethernet S1 Figure 5. Removing protective cover Figure 6 on page 13 shows the orientation of the DIP switches in the On and Off positions. S1 Front Rear S1 Switch toggle Push toggle up ON for ON position Push toggle down for 1234 OFF position Figure 6. DIP switch orientation 13 ON 4 123 ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON
Résumé du contenu de la page N° 14
4.2 CONFIGURING DIP SWITCH S1 DIP switch S1 is where you configure the CopperLINK line. The following table describes the configuration for the 2150. Table 1: 2150 Firmware Configuration S1-1 S1-2 S1-3 S1-4 Position Master/ Mode SNR Rate Slave ON Slave Fast 6dB 10/10 (CPE) OFF Master Interleave 9dB 10/10 (CO) S1-2: Impulse Noise Protection Fast Mode: Direct data transmission with latency less than 1ms Interleave Mode: Provides data transmission protection for up to 250 ms impulse noise wi
Résumé du contenu de la page N° 15
5.2 FRONT PANEL LED STATUS MONITORS The Model 2150 features six front panel LEDs that monitor power, the Ethernet signals, the CopperLINK connection, and the remote/local set- ting. Figure 7 shows the front panel location of each LED. Table 2 on page 15 describes the LED functions. CopperLINK Ethernet Extender Ethernet 1 Power Link Ethernet 2 Local Remote LED LED LED LED LED LED Figure 7. Model 2150 front panel Table 2: Front panel LED description LED Status Description Pow
Résumé du contenu de la page N° 16
APPENDIX A SPECIFICATIONS A.1 LAN CONNECTION Two shielded RJ-45, 10/100Base-T, IEEE 802.3 Ethernet CopperLINK Connection: Shielded RJ-45 A.2 TRANSMISSION LINE Two-wire unconditioned twisted pair. A.3 COPPERLINK DISTANCE Distance: 5,000 (1.5 km) at 10 Mbps upstream/10 Mbps downstream Note Distances depend on selected line rate and line conditions. See Appendix D on page 19 for details. A.4 LED STATUS INDICATORS Power (Green) CopperLINK: Link (Green) Ethernet: Link (Green) & Act
Résumé du contenu de la page N° 17
APPENDIX B MODEL 2150 SERIES FACTORY REPLACEMENT PARTS AND ACCESSORIES Patton Model # Description Base Models 2150/E CopperLINK Multi Rate 100 Mbps Ethernet Extender; No power supply 2150/E-2PK CopperLINK Multi Rate 100 Mbps Ethernet Extender Kit (2 units preset to local and remote); No power supply 2150/EUI-2PK CopperLINK Multi Rate 100 Mbps Ethernet Extender Kit (2 units preset to local and remote); 110-240VAC 07M2150-UM User Manual Power Supplies 08055DCUI 100-240VAC (+5V reg. DC/2A) Uni
Résumé du contenu de la page N° 18
APPENDIX C MODEL 2150 SERIES INTERFACE PIN ASSIGNMENT C.1 10/100BASE-T INTERFACE RJ-45 Pin 1: TX+ Pin 2: TX- Pin 3: RX+ Pin 6: RX- Pins 4, 5, 7, 8: no connection C.2 COPPERLINK INTERFACE RJ-45 Pin 4: RING Pin 5: TIP Pins 1, 2, 3, 6, 7, 8: no connection 18
Résumé du contenu de la page N° 19
APPENDIX D DISTANCE CHART, BASED ON 24 AWG (0.5 MM) Throughput Signal Distance at Max Noise Rate Mode Distance in Feet Ratio (km) (megabits per (SNR) second) 10/10 6 dB Fast 4,500 9.99 (DS) (1.3 km) 9.99 (US) 10/10 6 dB Interleave 4,500 9.99 (DS) (1.3 km) 9.99 (US) 10/10 9 dB Fast 4,750 9.99 (DS) (1.4 km) 9.99 (US) 10/10 9 dB Interleave 5,000 9.99 (DS) (1.5 km) 9.99 (US) Note The actual distance and link performance may vary depending on the environment and type/gauge of wire used. Note
Résumé du contenu de la page N° 20
Copyright © 2010. Patton Electronics Company All Rights Reserved. 20
