Instruction d'utilisation Network Technologies ETH-4X1 / 2X1

Résumé du contenu de la page N° 1

R
NETWORK 1275 Danner Dr Tel:330-562-7070
TECHNOLOGIES Aurora, OH 44202 Fax:330-562-1999
INCORPORATED www.nti1.com
NTI
ETH-4X1 / 2X1 (MANUAL ETHERNET SWITCH)
INSTALLATION / USER GUIDE
MAN023 Rev Date 6/28/2002

Résumé du contenu de la page N° 2

Table of Contents Introduction........................................................................................................... 1 Glossary ............................................................................................................... 1 Limitations ............................................................................................................ 1 Application Examples ........................................................................................... 2

Résumé du contenu de la page N° 3

Application Examples 2

Résumé du contenu de la page N° 4

Materials Materials Supplied with this kit: • NTI ETH-4X1 / ETH-2X1 Manual Ethernet Switch • 120VAC or 240VAC -12VDC/.5A AC Adapter • This owner's manual Materials Not Supplied, BUT REQUIRED: • Ethernet Cables- Cat5(e)UTP straight-through with male-male connectors Preparation for Installation • A location should be chosen for the ETH-4X1 such that the ethernet cable from each supported device will reach it. • The ethernet cables must be run to the locations where the ETH-4X1 switch, COMMON, and

Résumé du contenu de la page N° 5

Features and Functions 1. Power- LED to indicate the ETH-4X1 Manual Ethernet Switch has power to operate 2. 12VDC .5A- female connection jack for the AC adapter 3. Select Switches- (1-4)- for manual control of "COMMON" and user selectable ports (1-4) 4. RS232- 9 pin DIN male (optional)- for computer control of "COMMON" and user selectable ports (1-4) 5. Status LEDs- for visual indication of switch connection between the "COMMON" and the user selectable ports (1-4) 6. User Selectable P

Résumé du contenu de la page N° 6

Installation 1. Position the ETH-4X1 Manual Ethernet Switch such that the ethernet cable from the COMMON , the AC adapter power cable, and the ethernet cables from the SELECTABLEs can reach the ETH-4X1 Manual Ethernet Switch. 2. Connect one end of an ethernet cable to the COMMON (See Fig.1.) Connect the other end of that cable to the "COMMON" port on the ETH-4X1 Manual Ethernet Switch. 3. Connect another ethernet cable between each SELECTABLE and the user selectable ports (1-4

Résumé du contenu de la page N° 7

Plug-in and Boot Up 1. Connect the AC adapter power connector to the 12VDC port on the ETH-4X1 Manual Ethernet Switch. Make sure the power connector is properly inserted. (See Fig. 3.) 2. Plug the AC adapter into a power outlet. The “Power” LED on the ETH-4X1 Manual Ethernet Switch should illuminate indicating that a proper power connection has been made. Status LED "1" should also illuminate indicating a connection between the "COMMON" port and user selectable port 1.

Résumé du contenu de la page N° 8

Any terminal program can be used to control the switch, if that program supports the given parameters (example HyperTerminal in Windows, Norton Commander terminal in DOS). An available standard serial port is needed. Accepted commands: Keystroke Action 1 Switch to port 1 2 Switch to port 2 3 Switch to port 3 (ETH-4x1-RS only) 4 Switch to port 4 (ETH-4x1-RS only) 0 Disconnect all D Deactivate buttons B Activate buttons (power-ON defaults) All other characters wi

Résumé du contenu de la page N° 9

Troubleshooting Each and every piece of every product produced by Network Technologies Inc is 100% tested to exacting specifications. We make every effort to insure trouble-free installation and operation of our products. If problems are encountered while installing this product, please look over the troubleshooting chart below. If an answer is not found in the chart, check the FAQs (Frequently Asked Questions) at our website at http://www.nti1.com or contact NTI directly for help at 800-

Résumé du contenu de la page N° 10

Warranty Information The warranty period on this product (parts and labor) is one (1) year from the date of purchase. Please contact Network Technologies Inc at (800) 742-8324 (800-RGB-TECH) or (330) 562-7070 for information regarding repairs and/or returns. A return authorization number is required for all repairs/returns. Copyright Copyright © 2002 by Network Technologies Inc, all rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, i