Résumé du contenu de la page N° 1
300 Series
Media Converter &
Industrial Ethernet Switches
Installation
Guide
1
12/29/2005
Résumé du contenu de la page N° 2
Industrial Ethernet Switch Installation Guide 302MC-XX 302MCE-XX-YY 304TX 305FX-XX 305FXE-XX-YY 306TX 306FX2-XX 306FXE2-XX-YY 308TX Where: XX = ST or SC and YY = -15, -40, or -80 2 12/29/2005
Résumé du contenu de la page N° 3
Copyright, © N-TRON Corp., 2005 820 S. University Blvd., Suite 4E Mobile, AL 36609 USA All rights reserved. Reproduction, adaptation, or translation without prior written permission from N-TRON Corp. is prohibited, except as allowed under copyright laws. Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos or other designations mentioned herein are trademarks of their respective owners. The information contained in this do
Résumé du contenu de la page N° 4
Safety Warnings ELECTRICAL SAFETY WARNING: Disconnect the power cable before removing the enclosure top. WARNING: Do not operate the unit with the top cover removed. WARNING: Do not work on equipment or cables during periods of lightning activity. WARNING: Do not perform any services on the unit unless qualified to do so. WARNING: Do not block the air vents. WARNING: Observe proper DC Voltage polarity when installing power input cables. Reversing voltage polarity can ca
Résumé du contenu de la page N° 5
Hazardous Location Installation Requirements 1. WARNING! Do not disconnect while circuit is live, unless area is known to be non-hazardous. 2. WARNING! Install only in accordance with Local & National Codes of Authorities Having Jurisdiction. 3. Class I, Div 2 Installations require that power connections must be current limited at the power source with an in-line fuse rated at 0.5A. 4. Class I, Div 2 installations require that all devices connected to this product must be UL app
Résumé du contenu de la page N° 6
300 Series Industrial Ethernet Switches The 300 Series Unmanaged Industrial Ethernet Switches support high speed layer 2 switching between ports. All N-TRON 300 Series switches are housed in a ruggedized steel enclosure, and provide Category-5 compliant 10/100-BaseT connections for high performance network design, and hub/repeater upgrades. The 302MC/MCE is a 2 port unmanaged media converter that converts 10/100BaseTX copper to 100BaseFX full duplex fiber. The 304TX, 306TX, and 3
Résumé du contenu de la page N° 7
PACKAGE CONTENTS Please make sure the Ethernet Switch package contains the following items: 1. 300 Series Unit 2. N-Tron Product CD Contact your carrier if any items are damaged. INSTALLATION Read the following warning before beginning the installation: WARNING FXE units contain a class 1 laser. Do not stare into the laser beam (fiber optic connector) when installing or operating the product. Never install or work on electrical equipment or cabling during periods of
Résumé du contenu de la page N° 8
DIN-Rail Mounting Install the unit in a standard DIN-Rail. Recess the unit to allow at least 5” of horizontal clearance for fiber optic cable bend radius (2” for TX models). To install the unit to 35mm industrial DIN-Rail, place To remove the unit from the 35mm industrial DIN-Rail, the top edge of the included mounting bracket on the back place a flat head screwdriver into the orange release clip of the unit against the DIN-Rail at a 15° angle as shown. found at the bottom of t
Résumé du contenu de la page N° 9
FRONT PANEL LNK Link LED for Fiber Optic Ports TX Fiber Optic Transmit Ports RX Fiber Optic Receive Ports ACT Activity LED for Fiber Optic Ports RJ45 Ports Ports 1-4 Auto sensing 10/100BaseT Connections Green LED lights when Power is connected NOTE: Each RJ45 data port has two LED’s for each connector. The lower LED indicates LINK status, and the upper LED indicates ACTIVITY. LED’s: The table below describes the operating modes: LED Color Description GREEN Power i
Résumé du contenu de la page N° 10
APPLYING POWER (Top View) Unscrew & Remove the DC Voltage Input Plug from the top header. Install the DC Power Cables into the Plug (observing polarity on unit). Plug the Voltage Input Plug back into the top header. All LED’s will flash ON Momentarily Verify the Power LED stays ON (GREEN). Note: Either V1 or V2 can be connected to power for minimal operation. For redundant power operation, V and V plugs 1 2 must be connected to separate DC Voltage sources. Use wire sizes of 16-
Résumé du contenu de la page N° 11
TROUBLESHOOTING 1. Make sure the (Power LED) is ON. 2. Verify that Link LED’s are ON for connected ports. 3. Verify cabling used between stations. 4. Verify that cabling is Category 5 (or greater) for 100Mbit Operation. 5. Verify TX is connected to far end RX and vise versa (fiber optic units only). SUPPORT Contact N-TRON Corp. at: TEL: 251-342-2164 FAX: 251-342-6353 www.n-tron.com support@n-tron.com FCC STATEMENT This product complies with Part 15 of the FCC-A Rules
Résumé du contenu de la page N° 12
KEY SPECIFICATIONS Physical Height: 3.98” (max.) Width: 2.01” (max.) Depth: 4.19” (max.) Weight: 0.75 lbs. Electrical Input Voltage: 10-30 VDC (Regulated) Input Current: 290mA max. @ 24VDC (Steady State) Inrush Current: 8.0Amp/0.6ms max. @ 24VDC Input Ripple: Less than 100 mV Input Wire Size: 16-28 AWG Environmental Operating Temperature: -20°C to 70°C Storage Temperature: -20°C to 85°C Operating Humidity: 10% to 90% (Non Condensing) Operating Altit
Résumé du contenu de la page N° 13
N-TRON Limited Warranty N-TRON, Corp. warrants to the end user that this hardware product will be free from defects in workmanship and materials, under normal use and service, for the applicable warranty period from the data of purchase from N-TRON or its authorized reseller. If a product does not operate as warranted during the applicable warranty period, N-TRON shall, at its option and expense, repair the defective product or part, deliver to customer an equivalent product or part to re
