Résumé du contenu de la page N° 1
Moxa EtherDevice Switch
EDS-728/828 Hardware Installation Guide
First Edition, January 2008
Moxa Inc.
Tel: +886-2-8919-1230
Fax: +886-2-8919-1231
www.moxa.com
Moxa Technical support.
Worldwide: support@moxa.com
The Americas: support@usa.moxa.com
P/N: 1802008280010
Résumé du contenu de la page N° 2
Panel Layout of EDS-728/828 Series 12 11 8 4 10 3 9 2 7 1 6 5 1 SPEED FDX/HDX PWR1 PWR2 FAULT P3 P4 P3 P4 P3 P4 STAT LNK/ACT PWR PWR PWR RING COUPLER MASTER COUPLER T.RING P1 P2 P1 P2 P1 P2 PORT PORT MODE V1 V2 INPUT: 24VDC I2 DI2 3 4 3 4 I1 34 DI1 TX TX V2+ PWR2 P2 V2- P2 P1 P1 RX RX V1+ PWR1 V1- 2 1 2 1 2 2 12 RELAY2 TX TX RELAY1 1 1 RS-232 Console RX RX 1M-2 GTX 1M-2 GSFP IM-4TX IM-4MST IM-4MSC
Résumé du contenu de la page N° 3
15 13 14 13 15 16 13 1. System status LEDs 2. Push-button switch to select mode for Interface Module 3. Interface Module mode LEDs 4. Fast Ethernet Interface Module port LEDs 5. Terminal block for 2 power inputs, 2 DIs, and 2 DOs 6. Sticker showing pin contacts 7. Serial console port 8. Screw to attach Fast Ethernet Interface Module 9. Gigabit Ethernet Module LEDs 10. Two cartridge receptors for Gigabit Ethernet Interface Modules 11. Fast Ethernet Interface Modules 12. Socke
Résumé du contenu de la page N° 4
Mounting Dimensions (unit = mm) 381.70 EtherDevice Switch EDS-728/828 Front View 80.6 201.2 362.40 401.00 Rear View 128.00 Fast Ethernet Interface Modules 40 100 Side View Front View Side View Gigabit Ethernet Interface Modules 101.1 24 65.9 Front View Side View 3 140.00 142.47 127.8 85.00 30 127.8 142.47
Résumé du contenu de la page N° 5
DIN-Rail Mounting The DIN-Rail attachment plates are permanently fixed to the back panel of the EDS-728/828. Do not attempt to remove the attachment plates, since doing so could damage the product. To Install: Lock the brace by pressing the clips and then insert the top of the DIN-Rail into the notches at the bottom of the top array of heat radiating ribs. Press the EDS until the brace snaps into place. To Release: Use a flat-blade screw driver as a lever to force the braces downwar
Résumé du contenu de la page N° 6
STEP 2: Mounting the EDS-728/828 on the wall requires 4 screws to 6.0 mm ensure that the switch does not come loose from the wall. Use the switch, with wall mounting plates attached, as a guide to mark the correct locations of the 4 screws. The heads of the screws should be less than 6.0 mm in diameter, 3.5 mm and the shafts should be less than 3.5 mm in diameter, as shown in the figure at the right. Before tightening the screws into the wall, make sure the screw NOTE head and shank
Résumé du contenu de la page N° 7
Wiring Requirements WARNING Safety First! Be sure to disconnect the power cord before installing and/or wiring your Moxa EDS-728/828. Calculate the maximum possible current in each power wire and common wire. Observe all electrical codes dictating the maximum current allowable for each wire size. If the current goes above the maximum ratings, the wiring could overheat, causing serious damage to your equipment. You should also pay attention to the following guidelines: Use separ
Résumé du contenu de la page N° 8
Top View FAULT: The two sets of relay V1- V1+ V2- V2+ I1 I2 contacts of the 6-pin terminal block connector are used to detect user-configured events. The two wires attached to the Fault contacts RELAY1 RELAY2 PWR1 PWR2 DI1 DI2 form an open circuit when a user-configured event is triggered. Front View If a user-configured event does not occur, the Fault circuit will be closed. Wiring the Redundant Power Inputs The EDS-728/828 has two sets of power input—power input 1 and power input
Résumé du contenu de la page N° 9
Communication Connections The pinout and cable wiring diagrams in this section show how the ports on the EDS-728/828 connect to other devices: Pinouts are diagrams that indicate the type of signal passing through each of the port’s pins. 1. The pin numbers for male DB9 and DB25 connectors, and hole NOTE numbers for female DB9 and DB25 connectors are labeled on the connector. However, the numbers are typically quite small, so you may need to use a magnifying glass to see the numbers cl
Résumé du contenu de la page N° 10
MDI/MDI-X Port Pinouts Pin Signal 1 TRD(0)+ 1 8 2 TRD(0)- 3 TRD(1)+ 4 TRD(2)+ 5 TRD(2)- 6 TRD(1)- 7 TRD(3)+ 8 TRD(3)- 100/1000Base Fiber Port Connection The concept behind the duplex port and cable is quite straightforward. Suppose you are connecting devices I and II. Contrary to electrical signals, optical signals do not require a circuit in order to transmit data. Consequently, one of the optical lines is used to transm
Résumé du contenu de la page N° 11
This EDS-728/828 is the Master of this On Turbo Ring. This EDS-728/828 has become Ring MASTER GREEN Blinking Master of this Turbo Ring after the Turbo Ring was broken. This EDS-728/828 is not the Master of Off this Turbo Ring. When this EDS-728/828 enables the On coupling function to form a back-up path. COUPLER GREEN When this EDS-728/828 disables the Off coupling function. This EDS-728/828 does not belong to an Off active Turbo Ring. T.RING GREEN This EDS-728/828 belongs to
Résumé du contenu de la page N° 12
Fast Ethernet Module LEDs Power is being supplied to the interface On module. PWR GREEN Power is not being supplied to the Off interface module. On/ P1/P2/ Displays the module port’s status by GREEN Off/ P3/P4 mode. Blinking Gigabit Ethernet Module LED On/ Displays the module port’s status by P1/P2 GREEN Off/ mode. Blinking Specifications Modular Managed Switch System, EDS-72810G/82810G Modular Managed Switch System with 6 slots, and up to 28 ports. Technology Standa
Résumé du contenu de la page N° 13
Two inputs with the same ground, but electrically Digital Inputs isolated from the electronics. For state “1”: +13 to +30V For state “0”: -30 to +3V Max. input current: 8 mA Power Input Voltage 24 VDC (12 to 45 VDC), redundant dual inputs Connection Two removable 6-pin terminal blocks EDS-72810G/82810G 22.9W Power Consumption IM-4TX 2.5W IM-2MSC/2TX 5W IM-2MST/2TX 5W IM-2SSC/2TX 5W IM-4MSC 7.2W IM-4MST 7.2W IM-4SSC 7.2W IM-1LSC/3TX 4W IM-2GTX 3W IM-2GSFP
Résumé du contenu de la page N° 14
Optical Fiber/SFP-1GxxxLC Series SX LX LHX ZX Wavelength 850 nm 1310 nm 1310 nm 1310 nm Max. Tx -4 dBm -3 dBm 1 dBm +5 dBm Min. Tx -9.5 dBm -9.5 dBm -4 dBm 0 dBm Rx Sensitivity -18 dBm -20 dBm -24 dBm -24 dBm Link Budget 8.5 dB 10.5 dB 20 dB 24 dB 1100m (c) 550m (a) Typical Distance 550m (d) 40km (e) 80km (f) 275m (b) 10km (e) Saturation 0 dBm -3 dBm -3 dBm -3 dBm a. [50/125 μm, 400 MHz*km] cable b. [62.5/125 μm, 200 MHz*km] cable c. [50/125 μm, 800 MHz*km] cable d. [62.5/125 μ
Résumé du contenu de la page N° 15
IM-2MSC/2TX: Interface Module with 2 multi mode 100BaseFX ports, SC connectors, and 2 10/100BaseT(X) ports, RJ45 connectors. IM-2MST/2TX: Interface Module with 2 multi mode 100BaseFX ports, ST connectors, and 2 10/100BaseT(X) ports, RJ45 connectors. IM-2SSC/2TX: Interface Module with 2 single mode 100BaseFX ports, 40 km SC connectors, and 2 10/100BaseT(X) ports, RJ45 connectors. IM-1LSC/3TX: Interface Module with 1 single mode 100BaseFX port, 80 km SC connector and 3 10/100BaseT(X) por
Résumé du contenu de la page N° 16
IM-2MST/2TX 250 g IM-2SSC/2TX 245 g IM-1LSC/3TX 235 g IM-4MSC 250 g IM-4MST 270 g IM-4SSC 270 g Environmental Operating Temperature 0 to 60°C (32 to 140°F) Storage Temperature -40 to 85°C (-40 to 185°F) Ambient Relative 5 to 95% (non-condensing) Humidity Regulatory Approvals UL60950-1, CSA C22.2 No. 60950-1, Safety EN60950-1 (Pending), UL508 (Pending) UL/cUL Class I, Division 2, Groups A, B, C and D Hazardous Location (Pending) ATEX Class I, Zone 2, EEx nC IIC (Pendin
