Résumé du contenu de la page N° 1
Installation Guide
24-port 10/100 Fast Ethernet Switch
with 1 Fiber Connection
Model Name: KS-324F
Résumé du contenu de la page N° 2
We make no warranties with respect to this documentation and disclaim any implied warranties of merchantability, quality, or fitness for any particular purpose. The information in this document is subject to change without notice. We reserve the right to make revisions to this publication without obligation to notify any person or entity of any such changes. Trademarks or brand names mentioned herein are trademarks or registered trademarks of their respective companies.
Résumé du contenu de la page N° 3
Contents 1. Introduction 1.1 Package Contents 2. Where to Place the 24port Switch 3. Configure The Network Connection 3.1 Connecting Devices to the 24port Switch 3.2 Connecting to Another Ethernet Switch/Hub 3.3 Application 4. For 100BaseFX Connection 4.1 Adding 100BaseFX Module 5. LED Conditions Definition 5.1 LEDs Defined 6. Configure from Console 6.1 Hardware Setting for console 6.2 Operation in Console Appendix A - Product Specifications Appendix B - Cab
Résumé du contenu de la page N° 4
Résumé du contenu de la page N° 5
1. Introduction This 24port Switch is a 24-port 10/100Mbps Fast Ethernet switch. This switch supports the advanced features for current switch design. This switch can auto detect the 10/100Mbps speed, full/half duplex mode and MDI/MDI-X connection. These features provide user the simplest way to complete the network connection. There is a console port on the switch. You can configure the switch from the console for VLAN setting, port setting and priority setting. Port 24 could be
Résumé du contenu de la page N° 6
2. Where To Place the 24port Switch This 24port Switch can be placed on a flat surface (your desk, shelf or table). Place the 24port Switch at a location with these connection considerations in mind: l The switch configuration does not break the rules as specified in Section 3. l The switch is accessible and cables can be connected easily to it. l The cables connected to the switch are away from sources of electrical interference such as radio, computer monitor, and light fixtures. l
Résumé du contenu de la page N° 7
3. Configure the Network Connection 3.1 Connecting Devices to the 24port Switch [ Connection Guidelines: ] l Use Category 3 or 5 twisted-pair Ethernet cable when connecting 10BaseT devices to the switch (cable pin assignments defined in Appendix A) l Use Category 5 (straight-through) twisted-pair Ethernet cable when connecting 100BaseTX devices to the switch (cable specifications are defined in Appendix B) l Always limit the cable distance to 100 meters (328 ft) as defined by IEEE
Résumé du contenu de la page N° 8
Max. 100m (328 feet) TO: MDI or MDI-X port 3.3 Application A switch can be used to overcome the hub to hub connectivity limitations as well as improve overall network performance. Switches make intelligent decisions about where to send network traffic based on the destination address of the packet. As a result, the switch can significantly reduce unnecessary traffic. The example below demonstrates the switch ability to segment the network. The number of nodes on each segment is reduced
Résumé du contenu de la page N° 9
4. For 100BaseFX Connection 4.1 Adding 100BaseFX Module This 24port switch has a module port for 100BaseFX connection extension. You can add a 100BaseFX module to the switch and this switch gets a 100BaseFX port for long distance fiber optic cable connection. But when this module is added, the 24th TP port will be disable and this FX port become the Module Port 24th port. Please follow the steps to add the module to the switch. 1. Turn off the switch. 2. Loosen the screws of the
Résumé du contenu de la page N° 10
5. LEDs Conditions Definition 5.1 LEDs Defined The LEDs provide useful information about the switch and the status of all individual ports. LED STATUS CONDITION Power ON Switch is receiving power. Link / Act ON Port has established a valid link. Flashing Data packets being received or sent. Green The connection speed is 100Mbps. Yellow The connection speed is 10Mbps. FDX / Col ON The connection is Full Duplex. Flashing Packet collisions occurring. A low level of collisio
Résumé du contenu de la page N° 11
6. Configure from Console 6.1 Hardware Setting for Console Before using the console connection to configure the switch, please make sure that you have already install the terminal program "HyperTrm" in your Windows. If you can not find it in your Windows, please install it first with your Windows Installation Disk. You can also use other terminal program for console setting if you already have one. 1. Please connect from the console port of the switch to COM port of PC (COM1 or COM2
Résumé du contenu de la page N° 12
disable the backpressure function for half duplex. If it is enable, it can prevent packets lost in half duplex mode. But it will also reject packets when the network traffic is very heavy and that may cause some network connections fail. 2. Port Setting : You can set the operation speed, duplex mode from here. If "Auto_Negotiation" is enable, the settings in speed and duplex will be ignored. If "Auto_Negotiation" is disable, the speed and duplex setting will take effect. 3.
Résumé du contenu de la page N° 13
You can configure VLAN groups from this function. Because every port must belong to some VLAN, the removed port from VLAN will be assigned to Group 24 automatically if it does not belong to any VLAN any more after being removed. In the setting, VLAN groups can be overlapped on ports in this switch. 4. Priority Setting : There are two transmit priority queues for each port of the switch and you can configure the priority setting here. Port Based : If this setting of port is set t
Résumé du contenu de la page N° 14
A. Product Specifications Access Method CSMA/CD, 10 Mbps or 100 Mbps Standards Conformance IEEE 802.3 10BASE-T, IEEE 802.3u 100BASETX/FX Communication Rate 10/100Mbps on RJ-45 ports, 100Mbps on FX port Communication Mode Full / Half duplex Media Supported 10BASE-T - 100 Ohm Category 3,4,5 twisted- pair 100BASE-TX - 100 Ohm Category 5 twisted-pair 100BASE-FX - fiber optic cable Indicator Panel LEDs for Power (each unit), Link/Act, FDX/Col. (each port) Number of
Résumé du contenu de la page N° 15
B. Cable Specification Two different types of cable could be used on this 24port Switch: l Straight through cable l Cross-over cable l Fiber Optic cable if this 24port Switch has FX port Cable Schematics Straight-Through Cable Hub / Switch side Adapter side Pin # Pair # Pin # Pair # 1 RX+ White-Green ----------------- 1 RX+ White-Green 2 RX- Green ----------------- 2 RX- Green 3 TX+ White-Orange ----------------- 3 TX+ White-Ora
Résumé du contenu de la page N° 16
C. Compliances EMI Certification FCC Class A Certification (USA) Warning: This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A digital device pursuant to Subpart B of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated
Résumé du contenu de la page N° 17
D. Warranty We warrant to the original owner that the product delivered in this package will be free from defects in material and workmanship for a period of warranty time from the date of purchase from us or the authorized reseller. The warranty does not cover the product if it is damaged in the process of being installed. We recommend that you have the company from whom you purchased this product install it.
