Résumé du contenu de la page N° 1
TPS150
Twisted Pair A/V Switching and Transmission System
68-958-01 Rev. C
10 06
Résumé du contenu de la page N° 2
Precautions Safety Instructions � English Warning Power sources • This equipment should be operated only from the power source indicated on the product. This This symbol is intended to alert the user of important operating and maintenance equipment is intended to be used with a main power system with a grounded (neutral) conductor. The (servicing) instructions in the literature provided with the equipment. third (grounding) pin is a safety feature, do not a empt to bypass or disable it. Th
Résumé du contenu de la page N° 3
Quick Start — TPS150 Switching and Transmission System Step 7 Installation Connect a host device to the transmitter via this Step 1 9-pin D connector and a null modem serial Turn off power to the input and output devices, port cable for serial RS-232 control. and remove the power cords from them. Connected TPS150 RS-232 Step 2 pin device pin Function If desired, mount the TPT150 transmitter in a 51 1 — Not used rack. 2 RX Receive data 3 TX Transmit data 96 Step 3 4 — Not used Female If desired,
Résumé du contenu de la page N° 4
Quick Start — TPS150 Switching and Transmission System See chapter 4, “Serial Communications”, to: Step 10 Connect a projector or plasma display to the � Program a serial command to each of the receiver’s video outputs. transmitter’s Input Select buttons. Output 1 — Connect a � Program projector power on and power off VGA cable between the commands to the Projector Power button. 15-pin HD female � Set the projector power timeout function. connector and the VGA or RGB input on the � Program the p
Résumé du contenu de la page N° 5
Table of Contents Chapter 1 � Introduction ....................................................................................................... 1-1 About this Manual ............................................................................................................. 1-2 About the Transmission System .................................................................................. 1-2 About the TPT150 switching transmitter .............................................................
Résumé du contenu de la page N° 6
Table of Contents, cont’d Chapter 4 � Serial Communications ............................................................................... 4-1 ICS100 Windows-Based Control Program ............................................................... 4-2 System requirements ......................................................................................................... 4-2 Installing the software .................................................................................................
Résumé du contenu de la page N° 7
TPS150 Switching and Transmission System Chapter One 1 Introduction About this Manual About the Transmission System TP Cable Advantages Features
Résumé du contenu de la page N° 8
Intr Intr oduction, cont’d oduction About this Manual This manual contains installation, configuration, and operating information for the Extron TPS150 audio/video Twisted Pair (TP) switching and transmission system. � Chapter 1 identifies the transmitter’s and receiver’s features. � Chapter 2 details how to install the transmitter and receiver. � Chapter 3 describes how to operate the transmitter and receiver from their front panels and use all of their features. � Chapter 4 provides informatio
Résumé du contenu de la page N° 9
The audio for the selected input is output locally. It is not sent to the receiver. The TPT150 has an RS-232 port that accepts ICS100 program control from a connected computer or serial command control from a computer or control system. The transmitter can also store serial commands that are entered by the operator. The transmitter sends the appropriate serial commands on the TP link to the receiver whenever an input button or the projector power button is pressed. An optional CTP150CM control
Résumé du contenu de la page N° 10
Introduction, cont’d TP Cable Advantages Twisted pair cable is much smaller, lighter, more flexible, and less expensive than coaxial cable. The TPT150 makes cable runs simpler and less cumbersome. Termination of the cable with RJ-45 connectors is simple, quick, and economical. Transmission distance The maximum distance is determined by the output frequency and resolution. The following table specifies the recommended maximum transmission distances using CAT 5/5e/6 cable, terminated with the ap
Résumé du contenu de la page N° 11
Audio output volume adjustment and muting — The output has volume control adjustment via the front panel, RS-232 control, or optional contact closure panel control. Control — Switcher control is available through the front panel, an RS-232 port serial link, and an optional contact closure control panel. Serial control is provided with the Extron ICS 100 control software and/or a control system issuing serial commands. Custom engraved front panels — The front panel controllers include attachment
Résumé du contenu de la page N° 12
Introduction, cont’d 1-6 TPS150 Switching and Transmission System � Introduction
Résumé du contenu de la page N° 13
TPS150 Switching and Transmission System Chapter Two 2 Installation Mounting the Transmitter and Receiver Cabling and Rear Panel Views TP Cable Termination
Résumé du contenu de la page N° 14
Installation, cont’d Installation Mounting the Transmitter and Receiver The TPS150 comes with rubber feet for the transmitter and receiver, a set of MTR102 rack ears for the transmitter, and a set of mounting brackets for the receiver. Rack mounting the transmitter UL requirements The following Underwriters Laboratories (UL) requirements pertain to the installation of the transmitter into a rack (figure 2-1). 1. Elevated operating ambient temperature — If installed in a closed or multi- unit rac
Résumé du contenu de la page N° 15
CABLE EQUALIZATION - ADJUST + SELECT LOW FREQ. HIGH FREQ. POWER TPR150 Twisted Pair Video Receiver 3. Insert the transmitter into the rack, aligning the holes in the mounting bracket with those of the rack. 4. Secure the transmitter to the rack using the supplied machine screws. Projector mounting the receiver If desired, projector mount the receiver as follows: 1. Remove the rubber feet from the bottom of the receiver. 2. Attach the supplied 992547-2 projector pole mounting bracket to the recei
Résumé du contenu de la page N° 16
Installation, cont’d Cabling and Rear Panel Views Transmitter connections All connectors are on the rear panel (figure 2-3). CONTACT INPUT 1 INPUT 2 INPUT 3 INPUT 4 OUTPUT CLOSURE AUDIO AUDIO AUDIO AUDIO 100–240 V .3A VIDEO R-Y VIDEO R-Y GND PROJ PWR L L L L AUDIO LOCAL MONITOR VOL DN RGB / VGA OUTPUT RGB / VGA S-VIDEO S-VIDEO UTP LINK - VOL UP R + IN4 R R R R IN3 - L IN2 + Y B-Y Y B-Y IN1 50–60 Hz 1 2 4 1 4 3 4 3 4 5 6 7 8 9 10 Figure 2-3 — TPT150 transmitter rear panel connectors Vi
Résumé du contenu de la page N° 17
LR LR TP and audio output connections Output UTP Link connector — Connect one end of a TP cable to this RJ-45 5 female connector on the transmitter. Connect the free end of the same TP cable from the transmitter to the RJ-45 female connector on the receiver. See TP cable termination, on page 2-8, to properly wire the RJ-45 connector. The TPS150 works with either shielded or unshielded cables. However, to comply with FCC rules, shielded (STP or FTP) cables must be used. 6 Output Audio connector
Résumé du contenu de la page N° 18
USE ONLY WITH 250V FUSE Installation, cont’d RS-232 port — Connect a host device, such as a computer or touch panel 8 control, to the TPT150 transmitter via this 9-pin D connector and a null modem serial port cable for serial RS-232 control (figure 2-6). Connected TPS150 RS-232 Function pin device pin 51 1 — Not used 2 RX Receive data 3 TX Transmit data 96 4 — Not used Female 5 Gnd Signal ground 6 — Not used 7 — Not used 8 — Not used 9 — Not used Figure 2-6 — Remote port pin assignments for t
Résumé du contenu de la page N° 19
Video output connections RGB/VGA video connector — Connect a VGA cable between this 15-pin HD 12 female connector and the VGA or RGB input on the display. Composite video connector — Connect a video cable between this BNC 13 female connector and the composite video input on the display. S-video connector — Connect an S-video cable between this 4-pin mini DIN 14 female connector and the S-video input on the display. Component video connector — Connect a cable between these BNC female 15 connector
Résumé du contenu de la page N° 20
Installation, cont’d TP Cable Termination RJ-45 termination must comply with the TIA/EIA T 568A or TIA/EIA T 568B wiring standards for all connections. The TPS150 works with either shielded or unshielded cables. However, to comply with FCC rules, shielded (STP or FTP) cables must be used. Figure 2-8 details the recommended termination of CAT 5/5e/6 TP cable with RJ-45 connectors in accordance with the TIA/EIA T 568A or TIA/EIA T 568B wiring standards. You can use either standard, but ensure th
