Résumé du contenu de la page N° 1
Setup Guide
CrossPoint 450 Plus Series
MAV Plus Series
Large Scale Matrix Switchers
Extron USA - West Extron USA - East Extron Europe Extron Asia Extron Japan Extron China Extron Middle East
Headquarters
+800.633.9876 +800.3987.6673 +800.7339.8766 +81.3.3511.7655 +400.883.1568 +971.4.2991800 68-521-53 Rev. A
+800.633.9876 Inside USA / Canada Only Inside Europe Only Inside Asia Only +81.3.3511.7656 FAX Inside China Only +971.4.2991880 FAX
Inside USA / Canada Only 10 09
+1.919.863.1794 +31.33.45
Résumé du contenu de la page N° 2
Precautions Safety Instructions � English Warning Power sources � This equipment should be operated only from the power source This symbol is intended to alert the user of important indicated on the product. This equipment is intended to be used with a main power operating and maintenance (servicing) instructions in system with a grounded (neutral) conductor. The third (grounding) pin is a safety the literature provided with the equipment. feature, do not attempt to bypass or disable it.
Résumé du contenu de la page N° 3
警告 安全须知 • 中文 电源 • 该设备只能使用产品上标明的电源。 设备 这个符号提示用户该设备用户手册中 必须使用有地线的供电系统供电。 第三条线 有重要的操作和维护说明。 （地线）是安全设施，不能不用或跳过。 拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设备后 这个符号警告用户该设备机壳内有暴 或桌面电源的电源线，或任何接到市电系统的电源线。 电源线保护 • 妥善布线， 避免被踩踏，或重物挤压。 露的危险电压，有触电危险。 维护 • 所有维修必须由认证的维修人员进行。 设备内部 注意 没有用户可以更换的零件。为避免出现触电危险不要自 阅读说明书 • 用户使用该设备前必须阅读并理 己试图打开设备盖子维修该设备。 解所有安全和使用说明。 通风孔 • 有些设备机壳上有通风槽或孔，它们是用来防止 保存说明书 • 用户应保存安全说明书以备将来使 机内敏感元件过热。 不要用任何东西挡住通风孔。 用。 锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用 遵守警告 • 用户应遵守产品和用户指南上的所有安 与厂家推荐的相同或相近型号的电池。 按照生产厂的 全和操作说明。 建议处理废弃电
Résumé du contenu de la page N° 4
Table of Contents Chapter One • Introduction..................................................... 1-1 About this Manual..................................................................... 1-2 About the Matrix Switchers.................................................... 1-2 Chapter Two • Installation....................................................... 2-1 Rear Panel Installation Features............................................ 2-3 Video and audio connections, sync termination, and ext
Résumé du contenu de la page N° 5
Table of Contents, cont’d CrossPoint 450 Plus / MAV Plus Matrix Switchers Chapter One 1 Introduction About.this.Manual About.the.Matrix.Switchers ii CrossPoint / MAV Matrix Switchers • Table of Contents Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com.
Résumé du contenu de la page N° 6
Introduction For more information on any subject in this guide, refer to N TCP/IP the CrossPoint 450 Plus / MAV Plus User’s Manual, Network Control System available on the Extron DVD or at www.extron.com. BME 0 (red) BME 3 (horizontal) ANAHEIM, CA ANAHEIM, CA OUTPUTS 1 - 16 OUTPUTS 33 - 48 OUTPUTS 1 - 16 OUTPUTS 33 - 48 1 2 3 4 33 34 35 36 1 2 3 4 OUTPUTS INPUTS 33 34 35 36 OUTPUTS INPUTS 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 75 5 6 7 8 37 38 39 40 5 6 7 8 37 3
Résumé du contenu de la page N° 7
Introduction, cont’d CrossPoint 450 Plus / MAV Plus Matrix Switchers Chapter Two 2 Installation Rear.Panel.Installation.Features Front.Panel.Configuration .Port 1-4 CrossPoint / MAV Matrix Switchers • Introduction Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com.
Résumé du contenu de la page N° 8
Installation Extron recommends locking redundant front panel * N 3 1 controllers (if included in your system). See page 3-4. ANAHEIM, CA OUTPUTS 1 - 16 OUTPUTS 33 - 48 1 2 3 4 33 34 35 36 Rear Panel Installation Features INPUTS 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 75 5 6 7 8 37 38 39 40 Only sync BMEs have sync termination switches. N 510 9 10 11 12 13 14 15 16 10 12 14 16 9 11 13 15 75 9 10 11 12 41 42 43 44 Only MAV Plus video BMEs have External Sync connectors.
Résumé du contenu de la page N° 9
L R L R Installation, cont’d Audio inputs (audio BMEs) — Connect stereo or mono audio LAN port — If desired, connect a network WAN or LAN hub, a e h control system, or computer to the Ethernet RJ-45 port. sources to the 5-pole or 3-pole captive screw connectors. Tip Tip • Network connection — Wire as a patch (straight) cable. Sleeve Ring Sleeve (s) • Computer or control system connection — Wire the Tip Tip Sleeve Ring interface cable as a crossover cable. Unbalanced Stereo Inpu
Résumé du contenu de la page N° 10
Installation, cont’d Power connection CrossPoint 450 Plus / MAV Plus Matrix Switchers Power — Plug the switcher into a grounded AC source. k Front Panel Configuration Port CONTR CONTR CONTROL OL OL I/O I/O I/O VIEW VIEW VIEW ESC ESC ESC A A AUDIO UDIO UDIO VIDEO VIDEO VIDEO POWER SUPPLY I/O CONFIG PRIMARY REDUNDANT CROSSPOINT 450 PLUS SERIES ULTRA WIDEBAND MATRIX SWITCHER Chapter Three 12 3 Configuration port — If desired, connect a control system l or computer to the front panel Configu
Résumé du contenu de la page N° 11
Front Panel Operation 5. Press and release the Enter button. All button indicators 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 turn off. I 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 N P U T Saving or Recalling a Preset S 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 1. Save a preset — Press and hold the Preset button until it CONTROL I/O 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 flashes. VIEW VIEW VIEW ESC ESC ESC ENTER ENTER ENTER PRESET PRESET PRESET VIDEO VIDEO VIDEO A A AUDIO UD
Résumé du contenu de la page N° 12
Front Panel Operation, cont’d Selecting Lock mode 2 or toggling between Setting the Front Panel Locks (Executive Modes) mode 2 and mode 1 The matrix switcher has three levels of front panel security lock that limit the operation of the switcher from the front panel. The If the switcher is in Lock mode 0 or mode 1, this procedure N three levels are: selects mode 2. • Lock mode 0 — The front panel is completely unlocked. If the switcher is in Lock mode 2, this p
Résumé du contenu de la page N° 13
Front Panel Operation, cont’d Viewing Ties (and Muting Outputs) CrossPoint 450 Plus / MAV Plus Matrix Switchers 1. Press the View button. Output buttons light for outputs that have no ties established. If an output button blinks, that output is muted. N 2. Press an input button. The buttons for all tied outputs light (amber for video and audio, green for video only, and red for audio only). 3. Press an output button. The buttons for the tied input and all tied outputs light. 4
Résumé du contenu de la page N° 14
Remote Control Number of connections Selected SIS Commands ™ A switcher can have up to 200 simultaneous TCP connections, The switchers have Simple Instruction Set (SIS ) commands that including all HTTP sockets and Telnet connections. When you can use for operation and configuration. You can run these the connection limit is reached, the switcher accepts no new commands from a PC connected to either of the switcher’s serial connections until some have been closed. No error message or
Résumé du contenu de la page N° 15
Remote Control, cont’d 4-4 CrossPoint / MAV Matrix Switchers • Remote Control CrossPoint / MAV Matrix Switchers • Remote Control 4-5 Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com. Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com. Command ASCII command Response Additional description (host to switcher) (switcher to host) Create ties N • Commands can be entered back-to-back in a string, with no spaces. For example:
Résumé du contenu de la page N° 16
Remote Control, cont’d 4-6 CrossPoint / MAV Matrix Switchers • Remote Control CrossPoint / MAV Matrix Switchers • Remote Control 4-7 Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com. Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com. Command ASCII command Response Additional description (host to switcher) (switcher to host) Audio output volume Set the audio volume to a specific X@*X%V Out X@•Vol X%] value Example: 1*50v Out01•Vol50
Résumé du contenu de la page N° 17
Remote Control, cont’d 4-8 CrossPoint / MAV Matrix Switchers • Remote Control CrossPoint / MAV Matrix Switchers • Remote Control 4-9 Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com. Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com. Command ASCII command Response Additional description (host to switcher) (switcher to host) Information requests Information request I V X*XX(•A X*XX(T X1@UX1#] V X*XX( = video size, A X*X X( = audio si
Résumé du contenu de la page N° 18
Remote Control, cont’d 4. Follow the on-screen instructions. The installation Installing and Starting the Control Program program creates a C:\Program Files\Extron\ ® Another way to operate the switcher is via the Windows -based Matrix_Switchers directory and an “Extron Electronics\ Matrix Switchers Control Program. This program is contained Matrix Switchers” group folder. It installs the following on the Extron Software Products DVD (included with the four programs: switcher). Run th
Résumé du contenu de la page N° 19
Remote Control, cont’d 3. If you selected IP [LAN] in step 2, the IP Connection Accessing the HTML Pages window appears. Another way to operate the switcher is via its factory-installed HTML pages, which are always available and cannot be erased If you connect to the switcher via the LAN port, and it is the N or overwritten. The switcher’s HTML pages are accessible first time you have done so, you may change the controller’s through its LAN port, connected via a LAN or WAN, usin
Résumé du contenu de la page N° 20
Remote Control, cont’d After receiving the arp -s command, the controller Loading the start-up page changes to the new address and starts responding to the If your Ethernet connection to the matrix switcher is N ping requests, as described in step 5. unstable, try turning off the proxy server in your Web You must ping the CrossPoint or MAV switcher BME as N browser. In Microsoft Internet Explorer, click Tools > shown in step 5 for the IP ad
