Instruction d'utilisation Kenwood KTC-1000R

Résumé du contenu de la page N° 1

KTC-1000R
HIDEAWAY TUNER AMPLIFIER
INSTRUCTION MANUAL
B64-1449-00 (E) (DT) ‘99/6

Résumé du contenu de la page N° 2

Safety precautions 2WARNING 2CAUTION Do not use hard cloths or paint thinner, alcohol, To prevent injury and/or fire, take the or other volatile solvents. following precautions: • Ensure that the unit is securely installed. Otherwise it may fly out of place during collisions and other jolts. IMPORTANT INFORMATION • When extending the ignition, battery or ground Models which can be connected with this cables, make sure to use automotive-grade device are those that went on sale from 1998 2 cables

Résumé du contenu de la page N° 3

Installation n Accessories External view External view External view ......... Number of items ......... Number of items ......... Number of items 1 2 3 .........2 .........4 .........4 4 5 6 .........2 .........1 .........1 7 8 .........1 .........1 2CAUTION The use of any accessories except for those provided might result in damage to the unit. Make sure only to use the accessories shipped with the unit, as shown above. n Installation Procedure 1. To prevent short circuits, remove the key • If

Résumé du contenu de la page N° 4

Installation n Connecting Cables to Terminals 2WARNING If you connect the ignition cable (red) and the battery cable (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those cables to the power source running through the fuse box. Front left output (White) NOTE PREOUT REAR/NON-FAD FRONT Do not put anything into the fuse holder. TO 5L I/F TO MZ-BUS Rear left output (White) / Non-fading left output (White) FM•AM TUNER 44W· 4 AMPLIFI

Résumé du contenu de la page N° 5

2WARNING Connector Function Guide Connecting the ISO Connector The pin arrangement for the ISO connectors Pin Numbers for Cable Colour Functions depends on the type of vehicle you drive. Make ISO Connectors sure to make the proper connections to External Power prevent damage to the unit. Connector The default connection for the wiring harness A–4 Yellow Battery is described in 1 below. If the ISO connector A–5 Blue/White Power Control pins are set as described in 2 or 3, make the A–6 Orange Dim

Résumé du contenu de la page N° 6

O - N O - N Installation n When the control unit is the KVC-1000 Control unit (optional) KVC-1000 DAB control cable M 4 DAB tuner (optional) (Provided with the KTC-959DAB) NAV IN OUT I / F KTC-959DAB KTC-1000R 2WARNING Extention cable Changer control cable (5.5 m) (Black) (Accessory7) · ]"N" O N R KMD-D400 D/A CONVERTER 24BIT RESOLUTION MENU Changer control cable DISP DASC (Provided with the C907) 2WARNING 11BAND 500 750 1k 2k 4k 8k 16k SPECTRUM ANALYZER Only connect black cable to CD/MD chang

Résumé du contenu de la page N° 7

O - N O - N O - N O - N 1 - 2 1 - 2 n When two CD/MD changers are interconnected The disk changers are distinguished by source select disk-changer 1 and disk-changer 2. NOTE If the relevant connected device has a PROTOCOL SWITCH or O-N SWITCH, be sure to set the switch to “N” . NOTE Example 1 Do not connect the C907 and KDC-CPS81 at the same time. The equipment will cease functioning. TO 5L I/F TO MZ-BUS TO 5L I/F TO MZ-BUS ]"N" O N FM•AM TUNER 44W· 4 AMPLIFIER HIDEAWAY UNIT KTC-1000R R KMD-D4

Résumé du contenu de la page N° 8

Installation n Installation for Hideaway unit l Securing to audio board 1 2 Attach the installation brackets to the sides Use the tapping screw (ø4 · 16 mm) to of the hideaway unit using the sems bolts secure the hideaway unit to the audio (M4 · 8 mm). board. Tapping screw (ø4 · 16 mm) Installation brackets (Accessory3) (Accessory1) Sems bolts (M4 · 8 mm) (Accessory2) l Securing to pile carpet Peel the protective strips off of the velcro strips, attach them to the bottom of the Vel

Résumé du contenu de la page N° 9

Troubleshooting Guide PROBLEM POSSIBLE CAUSE SOLUTION The sound quality is poor or • A speaker cable may be pinched by • Check the speaker wiring.. distorted. a screw in the car. • The speakers are not cabled • Reconnect the speaker cables so correctly. that each output terminal is connected to a different speaker. Radio reception is poor. • The car antenna is not extended. • Pull out the antenna all the way. • The antenna control cable is not • Connect the cable correctly, connected. referring

Résumé du contenu de la page N° 10