Résumé du contenu de la page N° 1
1x 2x 3x 4x 5x 6x 7x 8x 9x 10x 11x 12x 13x 14x 15x 16x 16
CHAPTER 1
Overview
The FastHub 116T is an unmanaged 16-port 100BaseT Class II repeater for workgroups
and server farms. It is a member of an extended network system of stackable, modular LAN
and WAN products that increase LAN performance, connect remote offices and users, and
provide secure access. Figure 1-1 shows the network system units.
Figure 1-1 FastHub 116T in an Extended Network System of Stackable LAN and
WAN Products
Routers
Swit
Résumé du contenu de la page N° 2
Feature Summary Feature Summary The FastHub has 16 fixed 100BaseTX ports (with an alternative uplink port for connecting to other 100BaseTX hubs). Table 1-1 summarizes the FastHub features. Table 1-1 Feature Summary Feature Description Compatibility • IEEE 802.3u Class II repeater compliant. • Compatible with the 100BaseT standard for interoperability with other 100BaseT products. Performance 100-Mbps peak and aggregate throughput. Redundancy Supports connection to the optional Cisco redundant po
Résumé du contenu de la page N° 3
RPS 1x 2x 3x 4x 5x 6x 7x 8x 9x 10x 11x 12x 13x 14x 15x 16x 16 MODE Front Panel Description Figure 1-2 Front Panel Port Connectors 100BaseTX ports 100BaseTX uplink port Ports 1x through 16x have their transmit (TD) and receive (RD) pairs internally crossed. Standard Category 5 UTP crossover cable is required when connecting these ports to another hub, switch, or router (unless you are connecting to the uplink port on another FastHub or 100BaseT hub). Port 16, which is to the right of port 16x,
Résumé du contenu de la page N° 4
1x 2x 3x 4x Front Panel Description LEDs You can use the FastHub LEDs to monitor network activity and performance. Figure 1-3 shows the location of the LEDs and the Mode button. Figure 1-3 LEDs and Mode Button Port status LEDs Redundant power system LED System status LED Port mode LED Mode Collision button LED RPS LED The redundant power system LED shows the status of the RPS (see Table 1-2). Table 1-2 RPS LED Description Color RPS Status Off Power OK (no RPS or RPS not powered up). Solid green
Résumé du contenu de la page N° 5
Front Panel Description SYSTEM LED The system status LED shows whether the FastHub is powered up and provides an indication of any problem with the main system board of the FastHub (see Table 1-3). Note The system status LED and RPS LED are used together to isolate internal power supply or RPS problems. See the “Verifying and Troubleshooting Your Installation” section in the “Installing the FastHub” chapter for detailed information. Table 1-3 SYSTEM LED Description Color System Status Off FastHu
Résumé du contenu de la page N° 6
Front Panel Description Port Mode LED The port mode LED indicates the STAT (port status), UTL (bandwidth utilization), and ID (unit identification) modes. Note Port 16 (the uplink port) uses the port 16x LED. STAT Mode In port status mode, port LEDs show individual port status (see Table 1-5). Table 1-5 Port Status LED Description Color Port Status Off No link (link down). Green Link operational (with no activity). Flashing green Link operational (with activity). 1 Rapidly alternating green/amber
Résumé du contenu de la page N° 7
Front Panel Description UTL Mode In utilization mode, bandwidth usage is shown for the FastHub. The port LEDs show the current bandwidth and the peak bandwidth usage that occurred since the last reset. The far-right solid green LED denotes the peak bandwidth that was recorded since the last reset. All LEDs to the left of the solid green LED operate in a scalable pattern, flashing green from left to right, to show the current bandwidth utilization. Table 1-6 lists the port LEDs and the bandwidth a
Résumé du contenu de la page N° 8
DC INPUTS FOR REMOTE CONSOLE PORT POWER SUPPLY SPECIFIED IN MANUAL. For FastHub 200 AUI RATING +5V 6A +12V 1A and Catalyst only For Catalyst only 100-127/200-240V 0.5A/0.3A 50-60Hz Rear Panel Description Mode Button To change the mode being displayed by a port LED, press the Mode button to highlight in sequence each of the modes: STAT, UTL, and ID. The Mode button is independent of the Collision LED. When the desired mode is selected, release the button to make the change. As long as yo
Résumé du contenu de la page N° 9
Examples of Using the FastHub Examples of Using the FastHub This section describes several possible network configurations using the FastHub. Workgroups You can create 100-Mbps workgroups by interconnecting FastHubs (FastHub 116T, FastHub 216T, and FastHub 300 series), as shown in Figure 1-5. Figure 1-5 FastHubs in a Workgroup Application 100BaseT-enabled router or switch FastHub 116T Workgroup of up FastHub 316T to 14 users/servers FastHub 300 series FastHub stack 216T Workgroup of up to 31
Résumé du contenu de la page N° 10
Examples of Using the FastHub Server Farms Using the FastHub, you can create 100-Mbps server farms to increase centralized and decentralized server performance, as shown in Figure 1-6. Figure 1-6 FastHubs in a Server Farm Application 100BaseT-enabled 100BaseT-enabled router FastHub 216T 10-Mbps switch Centralized server farms Server farm of up to 15 servers FastHub 116T 10BaseT hub Server farm of up to 15 servers 10BaseT hub 1-10 FastHub 116T Installation Guide S6323
Résumé du contenu de la page N° 11
Examples of Using the FastHub Extended Network System A system of routers, switches, and hubs can be combined to create a high-performance network that extends beyond the main office LAN to connect to branch offices, remote sites, mobile users, and the Internet. Figure 1-7 is an application for an extended network system. Figure 1-7 FastHub in an Extended Network Application Branch office Internet Cisco 1600 or Catalyst 1900 2500 series series Main office 100BaseT Catalyst 2820 or server Catalys
Résumé du contenu de la page N° 12
Examples of Using the FastHub 1-12 FastHub 116T Installation Guide
