Résumé du contenu de la page N° 1
RAPIER SWITCH
QUICK INSTALL GUIDE
Résumé du contenu de la page N° 2
Rapier Switch Quick Install Guide Document Number C613-04017-01 REV D. Copyright © 1999-2002 Allied Telesyn International, Corp. 19800 North Creek Parkway, Suite 200, Bothell, WA 98011, USA. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesyn. Allied Telesyn International, Corp. reserves the right to make changes in specifications and other information contained in this document without prior written notice. The information p
Résumé du contenu de la page N° 3
Quick Install Guide 3 Documentation Roadmap Network Service Modules Uplink Module NSM Quick Install Guide Uplink Module Quick Install Guide Rapier Switch NSM Hardware Reference Uplink Module Hardware Reference Safety and Statutory Information Quick Install Guide Hardware Reference Port Interface Cards General Customer Support Software Reference Visit www.alliedtelesyn.co.nz for PIC Quick Install Guide the latest documentation, FAQ, User Guide PIC Hardware Reference and support information
Résumé du contenu de la page N° 4
4 Rapier Switch Package Contents The following items are included with each Rapier Switch. Contact your sales representative if any items are damaged or missing. ■ One Rapier Switch. ■ One AC power cord (AC models only). ■ One serial cable for connecting the switch to a terminal or PC. ■ One 19 inch rack-mount kit. ■ One Rapier Switch Quick Install Guide. ■ One Safety and Statutory Information booklet. ■ One Rapier Switch Documentation and Tools CD-ROM (which includes the complete Rapier Docum
Résumé du contenu de la page N° 5
Quick Install Guide 5 Installing the Switch All AC and DC versions of this equipment must be earthed. Follow these steps to install the switch: 1. Before installing the switch, read the safety information For safety information, see the Safety and Statutory Information booklet. A copy of this booklet is supplied with each switch, and can also be found on the Documentation and Tools CD-ROM or at www.alliedtelesyn.co.nz/ support/rapier/. 2. Gather the tools and equipment you will need If install
Résumé du contenu de la page N° 6
6 Rapier Switch Figure 1: Rapier front panel and rear panel with AC power inlet. Front panel Layer 3 Fast Ethernet Switch 25 10BASE-T / 100BASE-TX PORT ACTIVITY RS-232 STATUS TERMINAL PORT 1X 3X 5X 7X 9X 11X 13X 15X 17X 19X 21X 23X L/A 100M LINK / ACTIVITY 10M LINK / ACTIVITY D/C FULL DUP HALF DUP/ COL 1 3 5 7 9 11 13 15 17 19 21 23 ASYN0 L/A FAULT D/C L/A RPS 26 RESET D/C PWR 2 4 6 8 10 12 14 16 18 20 22 24 2X 4X 6X 8X 10X 12X 14X 16X 18X 20X 22X 24X Uplink Module Bays 10/1
Résumé du contenu de la page N° 7
Quick Install Guide 7 d) At the switch, connect the positive feed to the + (positive) terminal and the negative feed to the - (negative) terminal. Tighten the terminals to between 0.6 and 0.8 Nm (0.041 to 0.055 pound-force per foot) e) Ensure that there are no exposed conductor strands f) Secure the supply cable (to the rack framework or similar object) so that the connections are isolated from any forces applied to the cable g) Ensure that the circuit breaker is in the Off position h) Connec
Résumé du contenu de la page N° 8
8 Rapier Switch 2. Set the communication parameters Set the communication parameters on your terminal or terminal emulation program to: Baud rate: 9600 Data bits: 8 Parity: None Stop bits: 1 Flow control: Hardware 3. Log in After the switch has booted, the log in prompt appears. If the log in prompt doesn’t appear, press [Enter] two or three times. When the switch boots for the first time it automatically creates an account with manager privileges. The account has the log in name “man
Résumé du contenu de la page N° 9
Quick Install Guide 9 Using the GUI to configure a switch The GUI can be accessed through the switch’s default VLAN (VLAN1). To set-up the GUI the first time it is used, you must first access the CLI. 1. Access the CLI Follow the instructions in the previous section: “Using the CLI to configure a switch”. 2. Enable IP At the CLI, enter the command: ENABLE IP 3. Assign an IP address to VLAN1 Assign the VLAN1 interface an IP address in the required subnet, using the command: SET IP INTERFACE=v
Résumé du contenu de la page N° 10
10 Rapier Switch System LEDs and What They Mean System LEDs on its front panel indicate the switch’s operational status. System LEDs LED State Function Power Green The switch is receiving power and the voltage is within the acceptable range Fault Red The switch or management software is malfunctioning 1 flash A switch fan has failed. (The LEDs will not indicate an RPS fan failure.) 3 flashes If an RPS is connected, the switch’s PSU (Power Supply Unit) has failed 4 flashes If RPS monitoring
Résumé du contenu de la page N° 11
Quick Install Guide 11 Documentation and Tools CD-ROM The Documentation and Tools CD-ROM bundled with each Rapier Switch contains the complete Documentation Set for Rapier Switches and their expansion options, as well as tools for managing the switch. This includes: ■ The Rapier Switch Safety Booklet, which provides safety and statutory information for the Rapier Switch and its expansion options. ■ The Rapier Switch Hardware Reference, which provides detailed information on the hardware feat
