Instruction d'utilisation Audiovox K-13

Résumé du contenu de la page N° 1

- 13 W
12 Volt DC powered remote controlled 13” television AVT - 1475
12 Volt DC powered remote controlled VHS Video Cassette Player AVP - 7000

















Audiovox Specialized Applications, LLC.
“The Mobile Electronics Company”
23319 Cooper Drive
Elkhart IN 46514
1 (219) 264 - 3135


1




Rev. C 1/12/99 BJ
P/N 8007131
10 of Page
www.audiovox.com
Installation Instructions
ithout Harness and Antenna Model K
ASA Electronics TV/VCP Floor Console

Résumé du contenu de la page N° 2

This manual contains specific instructions on how to install this automotive TV/VCP floo r console. Please read this manual thoroughly before installing the console into the vehicle. In order to maintain a safe mounting system, this console MUST be secured to the floor of the vehicle accord ing to the instructions contained in this manual. Failure to do so may result in the console becoming a projectile in the event of an accident. It is unlawful in most jurisdictions for a person

Résumé du contenu de la page N° 3

- Step # 1 Disassemble shroud Step # 2 Install brackets and straps Step # 3 Mount the console on the floor of the vehicle Step # 4 Install the VCP Step # 5 Install the TV Step # 6 Replace the console face and rear shroud ⇒ Remove the 4 Phillips screws securing the face of the console. 3 Rev. C 1/12/99 BJ P/N 8007131 10 of Page STEP #1) Disassemble shroud. 13 TV/VCP floor console: to install the K There are six (6) st

Résumé du contenu de la page N° 4

4 Rev. C 1/12/99 BJ P/N 8007131 10 of Page strap, as shown. soldering iron, if necessary, to melt holes in open strap and loop 2) Use Mount brackets, using only four screws. Do not use center hole. 1) Step #2) Install brackets and straps

Résumé du contenu de la page N° 5

- 5 Rev. C 1/12/99 BJ P/N 8007131 10 of Page (B) (A) shelf (B) using 1/8” drill bit. drill pilot holes on side of VCP shelf (A) and on bottom of TV 3) Pre

Résumé du contenu de la page N° 6

6 Rev. C 1/12/99 BJ P/N 8007131 10 of Page necessary. o help locate strap if 4) Attach both straps, use TV and VCP t

Résumé du contenu de la page N° 7

⇒ BEFORE DRILLING ANY HOLES VERIFY THAT THE DRILL BIT WILL NOT ICLE, ELECTRICAL WIRES, ITEMS THAT WILL IMPAIR THE OPERATION OF THE VEHICLE. THE BOLTS OF THE FLOOR CONSOLE MUST SECURE TO THE FLOOR PANEL OF THE RIFY THAT THE HOLES WILL BE IN THE PROPER LOCATIONS. ⇒ Set the console on the floor and of the vehicle and mark where the holes are to be drilled. Drill small 1/8” pilot holes to verify that the drill hole

Résumé du contenu de la page N° 8

⇒ ⇒ Connect the white RCA connector (customer supplied) from the console to the white audio output of the VCP ⇒ Connect the yellow RCA connector (customer supplied) from the console to t he yellow audio output of the VCP ⇒ Connect the DC power connector (customer supplied) to the DC power jack of ⇒ Slide the VCP into the slot in the front of the console ⇒ Secure the VCP into the console with the supplied strap 8 Rev. C 1/12/99 BJ P/N 8007131 10 of Pag

Résumé du contenu de la page N° 9

⇒ Connect the yellow RCA patch cord (customer supplied) to the yellow RCA video input jack on the rear of the television ⇒ Connect the white RCA patch cord (customer supplied) to the white RCA audio input on the rear of the televisio n ⇒ Connect the DC power connector (customer supplied) to the rear of the television ⇒ Connect the antenna “F” connector (customer supplied) to the rear of the television ⇒ Place the television on the shelf of the console. ⇒ Secure the television

Résumé du contenu de la page N° 10

⇒ Place the rear and face of the console over the body of the console. Gently tap into place. ⇒ Reinsta ll the four Phillips screws that held the face to the body. Rev. C 1/12/99 BJ P/N 8007131 10 of 10 Page Step 6) Replace the rear shroud and face of console.