Résumé du contenu de la page N° 1
SYNTHESIZED
TRUE DIVERSITY
U H F
WIRELESS
SYSTEM
UR-5 RECEIVER
UR-5D RECEIVER
UT-5 BELT PACK TRANSMITTER
UH-5 HAND-HELD MICROPHONE TRANSMITTER
DA-5L UHF ANTENNA DISTRIBUTION AMPLIFIER
•dbx® Noise Reduction
®
SAMSON
Résumé du contenu de la page N° 2
Introduction 1 System Features 3 Guided Tours 5 UR-5/UR-5D Front Panel 5 UR-5/UR-5D Rear Panel 8 UT-5 10 UH-5 13 Setting Up and Using the UHF Synth System 16 ® About dbx Noise Reduction and Tone Squelch 20 Trouble-shooting 21 UHF Synthesized Frequency Chart 24 UT-5 Multi-pin Lavalier Wiring Guide and Chart 25 About The DA-5L UHF Antenna Distribution Amplifier 28 Guided Tour - DA-5L Front Panel 29 Guided Tour - DA-5L Rear Panel 30 Setting Up and Using the DA-5L 31 DA-5L Groundin
Résumé du contenu de la page N° 3
OPEN SERVO - 240 Introduction Congratulations on purchasing the Samson UHF Synthesized True Diversity Wireless System! Although this product is designed for easy operation, we suggest you take some time out first to go through these pages so you can fully understand how we’ve implemented a number of unique features. Every wireless system consists of at least two components—a transmit- ter and a receiver. The Samson UHF Synth System you have purchased contains either our UT-5 belt-pack transmit
Résumé du contenu de la page N° 4
Introduction The concept behind a “true diversity” wireless system is that a single chassis houses two discrete receivers (called “channel A” and “channel B”) instead of one, with both tuned to the same frequency but with each using an independent antenna. A built-in computer chip then continu- ously scans the two receivers and determines which one has the clear- est and strongest reception, automatically (and silently) switching to that channel. This allows you to maintain the wireless commun
Résumé du contenu de la page N° 5
System Features The Samson UHF Synthesized True Diversity System utilizes state-of- the-art technology in wireless communications. Here are some of its main features: • 74 available channels organized in 10 different groups in both the receiver and transmitter, with up to 11 channels available for simulta- neous use. This makes our UHF Synth System the ideal choice in multi-user environments such as stage productions and live band performance. It is also specifically suited for systems that t
Résumé du contenu de la page N° 6
System Features • The UT-5 and UH-5 transmitters both accept standard 9-volt alkaline batteries, and the UR-5 and UR-5D receivers can accept any AC power voltage from 100 - 250 volts, without the need to change a voltage selector switch (our special current and voltage sensing circuitry does the job automatically for you). • Tuned coaxial antennas are included, with options for rear-mounting or remoting if extended range is required. • The UR-5D dual receiver actually contains two separate true
Résumé du contenu de la page N° 7
Guided Tour - UR-5/UR-5D Front Panel 2 3 4 5 2 6 1 GROUP CHANNEL AF LEVEL 5 RF LEVEL 4 6 5 5 A B 4 6 6 3 7 12 34 5 3 7 SAMSON 3 7 AVAILABLE / MUTE 2 8 POWER ANTENNA - A 12 34 5 UHF SYNTHESIZED DIVERSITY RECEIVER ANTENNA - B 2 8 2 8 1 9 0 10 1 9 1 9 AF LEVEL 0 0 dbx NOISE REDUCTION Synth Series UR-5 UR-5 UHF 5a RF LEVEL A B 12 34 5 AVAILABLE / MUTE 12 34 5 AF LEVEL 5b 5d 5e 5c 1: Power switch - Use this to turn the main power on and off. When the receiver is on, the display se
Résumé du contenu de la page N° 8
Guided Tour - UR-5/UR-5D Front Panel 5: Display section - Shows you information about the current status of your receiver. 5a: “A”/“B” LEDs - When signal is being received, one of these LEDs (which shows you whether the “A” or “B” channel is currently being used) will be lit. A computer chip inside the receiver constantly scans the two and automatically selects whichever is receiving the strongest, clearest signal. This “true diversity” switching is completely inaudible, but it effectively i
Résumé du contenu de la page N° 9
Guided Tour - UR-5/UR-5D Front Panel 5e: AF (Audio Frequency) Level display - This “ladder” display (simi- lar to the VU bar meter used on audio devices) indicates the presence of audio signal. When all five segments are lit, the outgoing signal is at maximum strength; when only the left-most segment is lit, the outgoing signal is at minimum strength. If no segments are lit, little or no signal is being output; see the “Trouble-shooting” section on page 21 for more details. 6: AF (Audio Fre
Résumé du contenu de la page N° 10
Guided Tour - UR-5/UR-5D Rear Panel 5 2 3 5 1 SAMSON MODEL No.UR-5 AC INPUT BALANCED UNBALANCED OUTPUT OUTPUT UHF SYNTHESIZED DIVERSITY RECEIVER POWER 120V~ 50 / 60Hz 11W -10dBm.600Ω -10dBv.5KΩ RATING (120V-240V VOLTAGE SENSING) SAMSON TECHNOLOGIES CORP. HICKSVILLE, NEW YORK, U.S.A. 1: AC input - Connect the supplied standard 3-pin “EEC” plug here. The UR-5 and UR-5D both contain automatic current and voltage sensing circuitry and so can accept any mains current from 100 - 250 volts without th
Résumé du contenu de la page N° 11
Guided Tour - UR-5/UR-5D Rear Panel 3: Unbalanced output* - Use this unbalanced high impedance (5K Ohm) 1/4” jack when connecting the UR-5 or UR-5D to consumer (-10) audio equipment. Wiring is as follows: + SIGNAL + SIGNAL GROUND GROUND 4: Output Mixing switch (UR-5D receiver only) - When on, the outputs from both receivers are mixed together equally into a single monophonic signal which appears at both sets of balanced and unbalanced outputs. 5: Rear-mount antenna knockouts - The receiver a
Résumé du contenu de la page N° 12
Guided Tour - UT-5 2 3 4 5 BATT AUDIO ANT INPUT OFF ON POWER ON OFF 1 5 INPUT Beltpack Transmitter UT-5 SAMSON 8 10 7 9 4 5 4 5 6 6 3 7 3 7 2 8 2 8 6 1 9 11 1 0 9 0 12 SAMSON GROUP CHANNEL MIC LEVEL UNAVAILABLE INPUT INST LEVEL INST 4 5 6 4 5 6 3 7 3 7 2 8 2 8 1 1 0 9 0 9 MIN MAX MIC MIN MAX 10
Résumé du contenu de la page N° 13
Guided Tour - UT-5 1: Power on-off switch* - Use this to turn the UT-5 on or off (to conserve battery power, be sure to leave it off when not in use). 2: Six-pin input connector - Connect your input device (lavalier mic, headset mic or instrument cable) here, using the supplied six-pin connector. A wiring diagram and chart (showing connections for many popular lavalier and headset mics) is presented on pages 25 - 27. 3: Battery LED - This LED is an indicator of battery strength. If the batt
Résumé du contenu de la page N° 14
Guided Tour - UT-5 6: Group selector - Use the supplied plastic screwdriver to set this to the desired Group (this must match the Group setting of the receiver— see the “Setting Up and Using the UHF Synth System” section on page 16 for more information). 7: Channel selector - Use the supplied plastic screwdriver to set this to the desired Channel (this must match the Channel setting of the receiv- er—see the “Setting Up and Using the UHF Synth System” section on page 16 for more information).
Résumé du contenu de la page N° 15
UNAVAILABLE 5 5 4 6 4 6 3 7 3 7 8 2 8 2 1 9 1 9 0 0 GROUP CHANNEL Guided Tour - UH-5 1 1 POWER MIC LEVEL ON 2 4 OFF 6 MIN MAX 5 - + 3 3 PULL TO OPEN 8 BATT dbx NR SAMSON UHF SYNTHESIZED UH-5 WIRELESS MICROPHONE FCC ID CCRUH-5 SAMSON MADE IN JAPAN OFF ON AUDIO 7 13
Résumé du contenu de la page N° 16
Guided Tour - UH-5 1: Power on-off switch* - Use this to turn the UH-5 on or off (to conserve battery power, be sure to leave it off when not in use). 2: Mic level control (trimpot) - Use the supplied plastic screwdriver to set this to the optimum microphone output level. See the “Setting Up and Using the UHF Synth System” section on page 16 for more information. 3: Battery holder - Insert a standard 9-volt alkaline battery here, being sure to observe the plus and minus polarity markings sho
Résumé du contenu de la page N° 17
Guided Tour - UH-5 7: Audio off-on switch - When set to the “on” position, audio signal is transmitted. When set to the “off” position, the audio signal is muted. Because the carrier signal remains during muting, no “pop” or “thud” will be heard. Note that turning this off does not turn off the transmitter power—it is simply a way to temporarily mute the transmission of audio signal. If you don’t plan on using the transmitter for extended periods, turn off the transmitter power by using the
Résumé du contenu de la page N° 18
OPEN OPEN Setting Up and Using the UHF Synth System The general procedure for setting up and using your UHF Synth System is basically the same regardless of the particular components you are using (i.e. UT-5 or UH-5; UR-5 or UR-5D): 1. Remove all packing materials (save them in case of need for future service) and mount the supplied “A” and “B” antennas to your receiver by inserting the BNC connector and twisting clockwise until snug. INPUT Beltpack Transmitter UT-5 SAMSON UHF Synth Series 1a.
Résumé du contenu de la page N° 19
Setting Up and Using the UHF Synth System tions) are more prone to feedback problems than unidirectional (cardioid or supercardioid) ones; in general, you can avoid feedback by taking care not to use any microphone directly in front of a PA speaker (if this is unavoidable, you can try using an equalizer to attenuate those high frequencies which are causing the feedback “squealing”). 2. Place a fresh 9-volt alkaline battery (not supplied) into your UT-5 or UH-5 transmitter, taking care to obser
Résumé du contenu de la page N° 20
Setting Up and Using the UHF Synth System used at the same location, all devices must be set to the same Group (though each will use its own Channel) or intermodulation noise may occur. If you are using the UR-5D receiver for the reception of a stereo signal (or for the reception of two simultaneous monophonic signals), both sides (Receiver 1 and Receiver 2) must be set to the same Group. If you are only using a single transmitter and receiver, you can select any Group and available Channel wi
