Résumé du contenu de la page N° 1
AUDIO/VIDEO CONTROL RECEIVER
RX-7000VBK
TV AUDIO
VCR CATV/DBS
DVD DVD MUILTI CD TAPE/MD
TV/DBS PHONO FM/AM
VCR ANALOG/DIGITAL SLEEP
SURROUND CENTER
ON/OFF 12 3
MENU MENU
TEST REAR-L
SURROUND
MODE 45 6
ENTER ENTER
CD-DISC EFFECT REAR-R
7/P 89
SOUND SEA MODE SUBWOOFER
10 0 +10
RETURN
FM MODE 100+
AUDIO/
TV/VCR
MASTER VOLUME
MENU
CATV/DBS
RX-7000V AUDIO/VIDEO CONTROL RECEIVER DIGITAL
SET
–
+
TEXT
EXIT STANDBY
DISPLAY
SURROUND ON/OFF
DVD CD
TV SOUND/DBS PHONO
POWER
VCR TAPE/MD
TV VOL CHANNEL VOLUME
Résumé du contenu de la page N° 2
Warnings, Cautions and Others Caution –– POWER switch! CAUTION RISK OF ELECTRIC SHOCK Disconnect the mains plug to shut the power off completely. The DO NOT OPEN POWER switch in any position does not disconnect the mains line. The power can be remote controlled. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. For U.S.A. The ligh
Résumé du contenu de la page N° 3
Table of Contents Parts Identification ...................................... 2 Using the DSP Modes ................................ 21 Getting Started........................................... 3 Available DSP Modes According to the Speaker Arrangement .. 23 Adjusting the 3D-PHONIC Modes .......................................... 24 Before Installation ...................................................................... 3 Adjusting the DAP Modes ...............................................
Résumé du contenu de la page N° 4
Parts Identification Become familiar with the buttons and controls on the receiver before use. Refer to the pages in parentheses for details. 1 2 34 5 67 8 9 p MASTER VOLUME RX-7000V AUDIO/VIDEO CONTROL RECEIVER DIGITAL – + STANDBY SURROUND ON/OFF DVD CD TV SOUND/DBS PHONO POWER VCR TAPE/MD FM AM THEATER LIVE CLUB DANCE CLUB HALL PAVILION MULTI JOG SOURCE SELECTOR INPUT ANALOG/DIGITAL DSP MODE SEA MODE FM/AM TUNING TUNER PRESET TUNER/SEA MEMORY FM MODE SPEAKERS BALANCE/SURROUND PHONES 12 ADJ
Résumé du contenu de la page N° 5
Getting Started This section explains how to connect audio/video components and speakers to the receiver, and how to connect the power supply. Before Installation Connecting the FM and AM Antennas General • Be sure your hands are dry. FM Antenna Connections • Turn the power off to all components. • Read the manuals supplied with the components you are going to connect. A B Locations • Install the receiver in a location that is level and protected from moisture. • The temperature around the recei
Résumé du contenu de la page N° 6
RIGHT 1 RIGHT 1 RIGHT 1 Basic connecting procedure AM Antenna Connections 4 2 3 1 Snap the tabs on the loop into the ANTENNA slots of the base to assemble the FM 75 AM loop. COAXIAL AM 1 Cut, twist and remove the insulation at the end of LOOP each speaker signal cable (not supplied). AM Loop Antenna AM EXT 2 Turn the knob counterclockwise. 2 1 3 3 Insert the speaker signal cable. 4 Turn the knob clockwise. Connecting the front speakers You can connect two pairs of front speakers (one pair to
Résumé du contenu de la page N° 7
About the speaker impedance Connecting the subwoofer speaker The required speaker impedance of the front speakers does differ You can enhance the bass by connecting a subwoofer. depending on whether both the FRONT SPEAKERS 1 and FRONT Connect the input jack of a powered subwoofer to the SPEAKERS 2 terminals are used or only one of them is used. SUBWOOFER OUT jack on the rear panel, using a cable with RCA pin plugs (not supplied). CASE 1 When you connect only one set of front speakers SUBWOOFER O
Résumé du contenu de la page N° 8
Video component connections CD player AUDIO RIGHT LEFT PHONO Use the cables with RCA pin plugs (not supplied). Connect the white plug to the audio left jack, the red plug to the CD player audio right jack, and the yellow plug to the video jack. CD If your video components have S-video (Y/C-separation) terminals, connect them using S-video cables (not supplied). Connecting these OUT (REC) video components through the S-video input/output terminals will TAPE To audio output give you better picture
Résumé du contenu de la page N° 9
DVD player TV and/or DBS tuner • When you connect the DVD player with stereo output jacks: When connecting the TV, DO NOT connect the TV’s video output to these video input terminals. DVD player B C A VIDEO RIGHT AUDIO RIGHT LEFT VIDEO S-VIDEO DVD DVD To audio output VIDEO TV SOUND AUDIO /DBS RIGHT LEFT VIDEO S-VIDEO DVD OUT (REC) VCR To front left/right channel audio output (or to audio mixed IN (PLAY) output if necessary) õ To S-video output TV To composite video output MONITOR OUT Connect
Résumé du contenu de la page N° 10
Notes: Digital connections • When shipped from the factory, the DIGITAL IN terminals have This receiver is equipped with three DIGITAL IN terminals — one been set for use with the following components. digital coaxial terminal and two digital optical terminals, and one – DIGITAL 1 (coaxial): For DVD player DIGITAL OUT terminal. – DIGITAL 2 (optical): For CD player You can connect any digital equipment such as — – DIGITAL 3 (optical): For digital TV broadcast tuner • DBS tuner, • When you want to
Résumé du contenu de la page N° 11
Connecting the Power Cord Putting Batteries in the Remote Control Before plugging the receiver into an AC outlet, make sure that all Before using the remote control, put two supplied batteries first. connections have been made. When using the remote control, aim the remote control directly at the remote sensor on the receiver. Plug the power cord into an AC outlet. 1 Keep the power cord away from the connecting cables and the antenna. The power cord may cause noise or screen interference. We rec
Résumé du contenu de la page N° 12
Basic Operations The following operations are commonly used when you play any sound source. IMPORTANT: From the remote control: When using the remote control, check to see if its Press one of the source selecting buttons. AUDIO/ remote control mode selector is set to the correct TV/VCR DVD DVD MUILTI CD TAPE/MD position: CATV/DBS To operate this receiver, set it to “AUDIO/TV/ TV/DBS PHONO FM/AM VCR.” VCR Turning the Power On and Off (Standby) On the front panel: STANDBY Selected source name appe
Résumé du contenu de la page N° 13
Signal and speaker indicators on the display Adjusting the Volume • The signal indicators light up to indicate the incoming channel signals. On the front panel: – Only the indicators for the incoming signals light up. MASTER VOLUME To increase the volume, turn MASTER • The frame of the signal indicator (except for “LFE” and “S”) – + VOLUME clockwise. lights up if the corresponding speaker is set to “LARGE” or To decrease the volume, turn it “SMALL” (for subwoofer, “YES”). counterclockwise. – Th
Résumé du contenu de la page N° 14
Listening only with headphones Attenuating the Input Signal You can listen with the headphones without deactivating both pairs of speakers; however, if you want to use the HEADPHONE mode When the input level of the playing source is too high, the sounds (see below), you must turn off both pairs of speakers. will be distorted. If this happens, you need to attenuate the input 1. Connect a pair of headphones to the PHONES jack on the front signal level to prevent the sound distortion. panel. 2. Pre
Résumé du contenu de la page N° 15
Basic Settings Some of the following settings are required after connecting and positioning your speakers in your listening room, while others will make operations easier. MULTI JOG IMPORTANT: 2. Turn MULTI JOG to adjust the When using the remote control, check to see if its balance. AUDIO/ remote control mode selector is set to the correct TV/VCR • Turning it clockwise decreases the left position: channel output. CATV/DBS To operate this receiver, set it to “AUDIO/TV/ • Turning it counterclockw
Résumé du contenu de la page N° 16
3. Repeat steps 1 and 2 to select the appropriate Setting the Subwoofer Information items for the other speakers. Register whether or not you have connected a subwoofer. Notes: Before you start, remember.... • Keep the following comment in mind as reference when adjusting. – If the size of the cone speaker unit built in your speaker is greater • There is a time limit in doing the following steps. If the setting is 3 than 4 /4 inches (12 cm ), select “LARGE,” and if it is smaller canceled before
Résumé du contenu de la page N° 17
MULTI JOG Low Frequency Effect Attenuator Setting 2. Turn MULTI JOG to select the delay time of the rear speaker If the bass sound is distorted while playing back a source using Dolby Digital or DTS Digital Surround, follow the procedure below. output. • Turn it clockwise to increase the delay time from 0 msec (“R. On the front panel ONLY: DELAY: 0ms”) to 15 msec (“R. DELAY: 15ms”). SETTING • Turn it counterclockwise to decrease the delay time from 15 1. Press SETTING repeatedly until msec (“R.
Résumé du contenu de la page N° 18
Before you start, remember... Digital Input (DIGITAL IN) Terminal • The digital input (DIGITAL IN) terminal setting should be Setting correctly done for the sources you want to select the digital input mode for. Without setting this digital input terminal When you use the digital input terminals, you have to register what correctly, you cannot change the input mode from analog input to components are connected to which terminals (DIGITAL IN 1/2/3). digital input even if you follow the procedure
Résumé du contenu de la page N° 19
Notes: The following can be stored for each source: • Volume level (see page 11) • Noise may come out of the speakers while searching or skipping a • Bass boost (see page 12) multi-sound source encoded with Dolby Digital or DTS Digital • Input attenuator mode (see page 12) Surround. If this happens, select “DOLBY DIGITAL” or “DTS” for digital input mode. • Subwoofer output level (see page 12) • When you change the source, the digital input mode will be • Balance (see page 13) automatically reset
Résumé du contenu de la page N° 20
Receiving Radio Broadcasts You can browse through all the stations or use the preset function to go immediately to a particular station. IMPORTANT: Using Preset Tuning When using the remote control, check to see if its AUDIO/ remote control mode selector is set to the correct TV/VCR Once a station is assigned to a channel number, the station can be position: quickly tuned. You can preset up to 30 FM and 15 AM stations. CATV/DBS To operate this receiver, set it to “AUDIO/TV/ VCR.” To store the pr
