Instruction d'utilisation Sanyo LNS-T03

Résumé du contenu de la page N° 1

LCD PROJECTOR LENS
MODEL NO. LNS-T03
LENS REPLACEMENT
AND INSTALLATION PROCEDURES
NOTES ON REPLACEMENT AND INSTALLATION
The procedures and the needed pars for lens installation depend on the type of
cabinet. Before installing or replacing the lens, make sure the type of cabinet of your
projector.
When installing or replacing the lens, make sure the Lens Model No. matches with to
your projector. Refer to the catalog, or contact your sales dealer for the proper Lens
Model No.
TYPE OF THE CABINE

Résumé du contenu de la page N° 2

NOTES ON LENS INSTALLATION • Lens installation and replacement should be made by the qualified service per- sonnel. • Be sure to install the lens following this procedure precisely. • The lens cover is attached to the lens for protection. Be sure to remove the lens cover from the lens before installation. • When installing or replacing the lens, be careful not to stain, scratch or damage its surface. LIST OF CONTENTS Following parts are included in the package. • LENS 1 pc • DRIVER 1 pc BE SURE

Résumé du contenu de la page N° 3

LENS REPLACEMENT AND INSTALLATION PROCEDURE {Type (1) Cabinet} Remove 2 Screws A and Remove Lower Lens B Cover. Push part B and pull the Lower Lens 1 Cover down and remove it. (See Fig. 1.) A LOWER LENS COVER Fig-1 C Remove 4 Screws C. Pull the Upper Lens Cover 2 toward front and remove it. (See Fig. 2.) UPPER LENS COVER C Fig-2 UPPER LENS COVER Remove 2 Screws D and Cover Plate from the 3 back of the Upper Lens Cover. (See Fig. 3.) COVER PLATE D Fig-3 -2-

Résumé du contenu de la page N° 4

Remove Lens Protection Cap from the rear (mounting side) of the Projection Lens and attach the 4 lens Attachment to the lens with 4 Screws. (Use screws attached to the lens.) See Fig. 4. LENS LOCK LEVER LENS ATTACHMENT Lens Attachment 01 POA-LNA-01 DRIVER INCLUDED (610 303 8742) IN THE LENS PACKAGE LENS MOUNTING Part No. (610 275 6029) BRACKET Fig-4 Fig-5 Grasp (release lock) the Lens Lock Lever and turn it fully upward. (See Fig. 6) Mount the Lens into the lens mounting bracket and grasp the l

Résumé du contenu de la page N° 5

Put back the Upper Lens Cover to the projector and Fix the Upper Lens Cover with 4 Screws C. 7 (See Fig. 2.) Put back the Lower Lens Cover to the projector. Fix the Lower Cover with 2 Screws A. (See Fig. 1.) UPPER LENS COVER LOWER LENS COVER Fig-8 -4-

Résumé du contenu de la page N° 6

LENS REPLACEMENT AND INSTALLATION PROCEDURE {Type (2) Cabinet} A Remove 2 Screws A and Remove Upper Lens Cover. Push part B and pull the Upper Lens 1 Cover up and remove it. (See Fig. 1.) UPPER LENS COVER B Fig-1 C Remove 4 Screws C. Pull the Lower Lens Cover 2 toward front and remove it. (See Fig. 2.) LOWER LENS COVER C Fig-2 D Remove 2 Screws D and Cover Plate from the 3 back of the Upper Lens Cover. (See Fig. 3.) UPPER LENS COVER COVER PLATE Fig-3 -5-

Résumé du contenu de la page N° 7

Remove Lens Protection Cap from the rear (mounting side) of the Projection Lens and attach the 4 lens Attachment to the lens with 4 Screws. (Use screws attached to the lens.) See Fig. 4. LENS LOCK LEVER LENS ATTACHMENT Lens Attachment 01 POA-LNA-01 DRIVER INCLUDED (610 303 8742) IN THE LENS PACKAGE LENS MOUNTING Part No. (610 275 6029) Fig-4 BRACKET Fig-5 Grasp (release lock) the Lens Lock Lever and turn it fully upward. (See Fig. 6) Mount the Lens into the lens mounting bracket and grasp the l

Résumé du contenu de la page N° 8

Put back the Lower Lens Cover to the projector and Fix the Lower Lens Cover with 4 Screws C. 7 (See Fig. 2.) Put back the Upper Lens Cover to the projector. Fix the Upper Cover with 2 Screws A. (See Fig. 1.) UPPER LENS COVER LOWER LENS COVER Fig-8 -7-