Résumé du contenu de la page N° 1
®
®
®
®
®
2-CHANNEL AMPLIFIERS
OPERATION & INSTALLATION
®®
Résumé du contenu de la page N° 2
Dear Customer, Congratulations on your purchase of the world's finest brand of car audio amplifiers. At Rockford Fosgate we are fanatics about musical reproduction at its best, and we are pleased you chose our product. Through years of engineering expertise, hand craftsman- ship and critical testing procedures, we have created a wide range of products that reproduce music with all the clarity and richness you deserve. For maximum performance we recommend you have your new Rockford Fosgate produc
Résumé du contenu de la page N° 3
TABLE OF CONTENTS Introduction ............................................................................................. 1 Punch Amplifier Accessory Pack .............................................................. 1 Technical Design Features ....................................................................... 2 Design Features........................................................................................ 5 Installation Considerations ...........................................
Résumé du contenu de la page N° 4
INTRODUCTION Rockford engineers designed the Punch 40x , 60x , 100x and 2 2 2 200x amplifiers to withstand the rugged automotive environment 2 while delivering superior sound quality in a flexible, reliable, and efficient package. TRANS•ANA is a low voltage circuit in the preamp stage of all Punch x amplifiers that lets the music sound crystal clear 2 and very real, even when played at high volume levels. This is matched with TOPAZ, a unique grounding circuit used to eliminate noise problems a
Résumé du contenu de la page N° 5
TECHNICAL DESIGN FEATURES TRANS•ANA (TRANSconductance Active Nodal Amplifier) The TRANS•ANA (TRANSconductance Active Nodal Amplifier) is a circuit that allows the audio signal to pass through the amplifier at low voltage. The signal is directly level-shifted to the fixed high voltage rails via a pair of driver transistors. Signal linearity is assured by an active node formed by the drive transistors at ultrasonic frequencies. This allows amplifier performance similar to trans•nova which is hig
Résumé du contenu de la page N° 6
DSM (Discrete Surface Mount) Technology The DSM (Discrete Surface Mount) manufacturing process combines the advantages of both discrete components and integrated circuitry. Rockford Fosgate is the only American amplifier manufacturer to have invested millions into this process. DSM components differ from conventional discrete components in different ways. They are more compact, more rugged, and they efficiently dissipate generated heat. Using them wherever appropriate allows the advantages ass
Résumé du contenu de la page N° 7
MOSFET Devices Rockford Fosgate is one of the few manufacturers in the sound community to utilize MOSFET devices in both the power supply and the output stages. MOSFET (Metal Oxide Semiconductor Field Effect Transistor) devices offer several important inherent advantages over the 30 year old technology of bi-polar design. These advantages include: thermal stability, switching speed, ultra low output imped- ance and wider bandwidth linearity. In addition, MOSFETs operate very similarly to vacuu
Résumé du contenu de la page N° 8
DESIGN FEATURES 1. Cast Aluminum Heatsink – The cast aluminum heatsink of the Punch amplifier dissipates heat generated by the amplifier's circuitry. The inherent advantage of casting provides a 30% improvement of cooling over conventional extrusion heatsink designs. 2. End Caps – Interchangeable end caps conceal the wiring and input cables, giving the amplifier a clean “stealth” look. 3 8 7 6 6 7 3 8 Speaker Speaker +L – +R – Left Left Right Right Treble Bass Gain Input Input Gain 9 5 4 11 LED
Résumé du contenu de la page N° 9
7. Input Sensitivity Controls – The input level controls are preset for 500mV which will match the output of most source units. They can be adjusted to match input levels ranging from 150mV to 3V. 8. Punch Equalization Controls – The Punch EQ helps correct for acoustical deficiencies of the listening environment. The Bass control allows a narrow band adjustment of up to 18dB centered at 45Hz. The Treble control is a wide band hinged adjustment with a maximum of 12dB at 20kHz. The Punch EQ ca
Résumé du contenu de la page N° 10
INSTALLATION CONSIDERATIONS The following is a list of tools you will need for installing the Punch amplifier: Allen wrenches 7/64" & 3/32" (included) Voltmeter Wire strippers Battery post wrench Electric hand drill w/assorted bits Wire cutters 17' (518.16cm) Red Power Wire Assorted connectors 12' (365.76cm) Remote Turn-On Wire Wire crimpers 1.5' (45.72cm) Black Grounding Wire This section focuses on some of the vehicle considerations for installing your new Punch amplifier. Checking your batte
Résumé du contenu de la page N° 11
MOUNTING LOCATION The mounting location and position of your amplifier will have a great effect on its ability to dissipate the heat generated during normal operation. The design of our cast aluminum heatsink serves to easily dissipate the heat generated over a wide range of operating condi- tions. However, to maximize the performance of your amplifier, care should be taken to ensure adequate ventilation. Trunk Mounting Mounting the amplifier vertically on a surface with the fin grooves running
Résumé du contenu de la page N° 12
> > > BATTERY AND CHARGING Amplifiers will put an increased load on the vehicle's battery and charging system. We recommend checking your alternator and battery condition to ensure that the electrical system has enough capacity to handle the increased load of your stereo system. Stock electrical systems which are in good condition should be able to handle the extra load of any Rockford amplifier without problems, although battery and alternator life can be reduced slightly. To maximize the perfo
Résumé du contenu de la page N° 13
Punch 40x , 60x , 100x 2 2 2 Trim the power cable to within 18" of the battery and install the protective rubber boot, which is packed with the fuseholder, over the end of the wire. Strip 3/8" of insulation from the wire and insert into the end of the fuseholder, then crimp it in place. Slide the rubber boot into place to cover the connection. Use the section of cable that was trimmed earlier and connect it to the other end of the fuseholder. Punch 200x 2 Mount the fuseholder within 18" of the b
Résumé du contenu de la page N° 14
6. Prepare the REM turn-on wire for connection to the amplifier by stripping 5/8" of insulation from the wire end and crimping an insulated spade connector in place. Slide the connector over the REM terminal on the amplifier. Connect the other end of the REM wire to a switched 12 volt positive source. The switched signal is usually taken from the source unit's auto antenna or the accessory lead. If the source unit does not have these outputs available, the recommended solution is to wire a mech
Résumé du contenu de la page N° 15
USING THE XCARD The crossover functions are controlled through the use of an XCard and can be set for high-pass, low-pass or full range operation. The 100Hz XCard shipped with your amplifier is set for Full Range. Each crossover card has two faces: one face operates Full Range, the other has arrows to indicate the edge for selecting HP (high-pass) or LP (low- pass) operation. Orient the card with the desired operating edge, indicated by the arrow, toward the socket terminals inside the ampli- fi
Résumé du contenu de la page N° 16
a O p d e v RESISTOR CHART r a a n t c i e o d n Use the resistor charts below to modify the factory shipped 100Hz XCard. Butterworth Alignment Q = .707 Butterworth Alignment Q = .707 1% resistors used with 0.047µµµµµ F caps 5% resistors used with 0.047µµµ F caps µµ Frequency R1 R2 Frequency R1 R2 20Hz 169kΩ 169kΩ 21Hz 160kΩ 160kΩ 25Hz 133kΩ 133kΩ 26Hz 130kΩ 130kΩ 30Hz 110kΩ 110kΩ 30.8Hz 110kΩ 110kΩ 35Hz 95.3kΩ 95.3Ω 37Hz 91kΩ 91Ω 40Hz 84.5kΩ 84.5kΩ 41Hz 82kΩ 82kΩ 45Hz 75kΩ 75kΩ 45Hz 75kΩ 75
Résumé du contenu de la page N° 17
P40x - 20A 2 P60x - 30A 2 P100x - 40A 2 P200x - 50A 2 ® ® I N S T INSTALLATION A L L A T I O N Power Connections LED REM B+ GND Punch Status Display Connect to remote Connect to chassis turn-on lead of ground of vehicle* source unit Less than 18" Connect to B+ of battery with appropriate fuse value *Keep grounds as short as possible – 14 –
Résumé du contenu de la page N° 18
® ® I N S T A L L A T I O N Stereo Operation RCA Input Speaker Speaker +L – Left Left Right Right +R – Treble Bass Gain Input Input Gain – 2Ω min. 2Ω min. + • RCA inputs are connected to both left and right channels • Gain for left and right channels operate independently • Impedance for each channel should be 2Ω minimum • XCard can be set for High-Pass, Low-Pass or Full Range – 15 – – +
Résumé du contenu de la page N° 19
® ® I N S T A L L A T I O N Mono Operation RCA Input Speaker Speaker +L – Left Left Right Right +R – Treble Gain Input Input Gain Bass + – 4 Ω min. • RCA inputs are connected to both left and right channels • Gain for left and right channels are set equally to balance the subwoofer • Impedance for mono channel should be 4Ω minimum • XCard can be set for High-Pass, Low-Pass or Full Range – 16 –
Résumé du contenu de la page N° 20
® ® I N S T A L L A T I O N Stereo/Mono Operation RCA Input Speaker Speaker Left Left Right Right +L – +R – Treble Gain Input Input Gain Bass + – 2Ω min. 2Ω min. – + + – 4Ω min. • RCA inputs are connected to both left and right channels • Gain for left and right channels are set equally to balance the subwoofer • Impedance for each channel should be 2Ω minimum • Impedance for mono channel should be 4Ω minimum • XCard are set for Full Range – 17 –
