Résumé du contenu de la page N° 1
KX100.2 & KX200.4 Tech-
nical Manual
KX100.2 & KX200.4 Technical Manual
Version 2.0
January 1, 2004
Résumé du contenu de la page N° 2
Features Radically Advanced Chassis with removable shroud and improved heatsink technology. The heatsinks provide the amplifier with longer runtime, improved reliability and performance. The height has been decreased for more versatile installations. For those Livin Loud , the shrouds may be painted to match your car! Low Impedance Operation The KX series amplifiers are stable down to 2 Ohm stereo and 4 Ohm mono. This will allow the installer flexibility when designing the system. It will be ea
Résumé du contenu de la page N° 3
Features cont. Custom tooled gold plated connectors Assure maximum power transfer and damping. SAMS (Stereo And Mono Simultaneously) Amplifier will operate into a bridged mono load and a stereo load at the same time. This type of system is great if the consumer is just starting out, or on a tight budget. Three Year Warranty When youre Livin Loud you want the tunes to roll non-stop and we couldnt agree more. When you purchase your KX Amplifier from an authorized KICKER dealer we back it up
Résumé du contenu de la page N° 4
Mounting Instructions When selecting a location to mount your Kicker amplifier be sure it is structurally sound and that there are no items behind the area that could be Remove Remove damaged by the screws. Check for wiring, brake lines, fuel lines, gas tanks, etc. All amplifiers generate heat under normal opera- tion. Be sure to choose a location that allows ade- quate ventilation for the amplifier. Also consider that the air temperature inside an automobiles trunk can reach upwards of 140 de
Résumé du contenu de la page N° 5
KX100.2 & KX200.4 Technical Manual Version 2.0 Page 5 Wiring Instructions KX100.2 Wiring WARNING-Use Only One... Never Both At The Same Time!!! Speaker RCA SOURCE UNIT Outputs Outputs RIGHT + High-Level RIGHT - LEFT - Inputs LEFT +
Résumé du contenu de la page N° 6
KX100.2 & KX200.4 Technical Manual Version 2.0 Page 6 Wiring Instructions KX200.4 Wiring WARNING-Use Only One... Never Both At The Same Time!!! RCA Speaker Outputs Outputs SOURCE UNIT High-Level Inputs RIGHT + LEFT + RIGHT - LEFT - *See note on page 7 if RIGHT - LEFT - using High-Level inputs! RIGHT + LEFT + AMP 1 AMP 2
Résumé du contenu de la page N° 7
KX100.2 & KX200.4 Technical Manual Version 2.0 Page 7 Wiring Instructions When using both sets of High Level inputs, the supplied RCA dummy plugs must be inserted into the AMP 2 inputs in order for the fader to work properly. If the amplifier is being used in any other configuration Do Not use the supplied dummy plugs! SOURCE UNIT RCA Dummy Plugs Speaker Outputs High-Level Inputs RIGHT + LEFT + RIGHT - LEFT - RIGHT - LEFT - RIGHT + LEFT + AMP 1 AMP 2
Résumé du contenu de la page N° 8
Wiring cont. The use of twisted pair interconnects is recommended for all installations to minimize noise. When routing these cables through the automobile, try to keep them away from factory wiring harnesses and other power wiring. If you need to cross any of this wiring do so at a 90 degree angle to reduce the possibility for noise problems. Source Factory Wiring Amplifier When working with power connections it is always recommended that you disconnect the battery to prevent accidents! The gro
Résumé du contenu de la page N° 9
Fuse Ratings Model Fuse Size Wire Size KX75.2 15A 8 GA KX150.4 30A 8 GA Specifications subject to change without prior notice. Adjusting Amplifier Controls On your Kicker amplifier there are rotary controls and switches on the end panel. These controls ensure the relia- bility and performance of the amplifier, so they need to be set correctly. If you are using a KX150.4 you will have two sets of rotary controls and switches. One set controls AMP1 and one set controls AMP2. BEFORE TURNING ON THE
Résumé du contenu de la page N° 10
Adjusting Amplifier Controls cont. Crossover Control Where you set the crossover is very subjective and can be fine tuned to match your listening preference or speaker requirement. If the amplifier is driving small speakers (crossover set to HI PASS) this will eliminate the low frequencies from damaging the high frequency speaker. If the amplifier is driving subwoofers (crossover set to LO PASS). These are only guidelines because setting the right frequency depends on the listeners preferences.
Résumé du contenu de la page N° 11
_ + _ + KX100.2 & KX200.4 Technical Manual Version 2.0 Page 11 System Diagrams KX100.2 Stereo Mode LEFT SPEAKER(S) 2 Ω Min. SIGNAL IN 2Ω Min. GROUND RIGHT SPEAKER(S) REMOTE TURN-ON 18" or less +12V FUSE BATTERY When the amplifier is driving speakers that do not require a crossover, the crossover switch may be set to the OFF position. This will allow the speakers to play full range. OR... If the amplifier is driving speakers that do require a crossover, set the switch to HI PASS. This will al
Résumé du contenu de la page N° 12
_ + KX100.2 & KX200.4 Technical Manual Version 2.0 Page 12 System Diagrams KX100.2 Mono Mode 4 Ω SIGNAL IN MONO SPEAKER Min. GROUND REMOTE TURN-ON 18" or less +12V FUSE BATTERY If the amplifier is used to drive subwoofers, set the switch to LO PASS. This will allow only low frequencies to pass through the amplifier to the woofers. - To Woofer +
Résumé du contenu de la page N° 13
_ _ + _ + + KX100.2 & KX200.4 Technical Manual Version 2.0 Page 13 System Diagrams KX100.2 SAMS Mode LEFT SPEAKER(S) LOW PASS CROSS- OVER HIGH PASS 2 Ω CROSSOVER Min. SIGNAL IN 4 Ω Min. GROUND HIGH PASS 2Ω CROSSOVER MONO Min. SPEAKER REMOTE TURN-ON RIGHT SPEAKER(S) 18" or less +12V FUSE BATTERY When the amplifier is driving speakers in the configuration above, the crossover switch should be set to the OFF position. This will allow the speakers to play full range. The speakers will need pass
Résumé du contenu de la page N° 14
KX100.2 & KX200.4 Technical Manual Version 2.0 Page 14 System Diagrams KX200.4 4 Channel Stereo Mode - - + + SIGNAL IN AMP 2 - - + + + - GROUND SIGNAL IN AMP 1 REMOTE TURN-ON 18" or less +12V FUSE BATTERY When AMP 1 or AMP 2 are driving speakers that do not require a crossover, the crossover switch may be set to the OFF position. This will allow the speakers to play full range. OR... If AMP 1 or AMP 2 are driving speakers that do require a crossover set the switch to HI
Résumé du contenu de la page N° 15
KX100.2 & KX200.4 Technical Manual Version 2.0 Page 15 System Diagrams KX200.4 3 Channel Stereo Mode - + - + SIGNAL IN AMP 2 - + GROUND SIGNAL IN AMP 1 REMOTE TURN-ON 18" or less +12V FUSE BATTERY When AMP 1 is driving speakers that do not require a crossover, the crossover switch may be set to the OFF position. This will allow the speakers to play full range. OR... If AMP 1 is driving speakers that do require a crossover, set the switch to HI PASS. This will allow onl
Résumé du contenu de la page N° 16
KX100.2 & KX200.4 Technical Manual Version 2.0 Page 16 System Diagrams KX200.4 2 Channel Mono Mode - + SIGNAL IN AMP 2 - + GROUND SIGNAL IN AMP 1 REMOTE TURN-ON 18" or less +12V FUSE BATTERY If AMP 1 or AMP 2 are used to drive subwoofers, set the switch to LO PASS. This will allow only low frequencies to pass through the amplifier to the woofers. MAKE SURE: * The LEFT input must be split up and fed to the L & R Amp 1 inputs with a Y-Adapter. * The RIGHT input must be spli
Résumé du contenu de la page N° 17
Formulas Ohm’s Law E = I X R Where: E = Voltage (Volts) I = Current (Amps or Amperes) WW R = Resistance (Ohms or ) Formula Variations: I =E / R R = E / I Power Formula P = I X E Where: P = Power (Watts) I = Current (Amps or Amperes) E = Voltage (Volts) Formula Variations: I = P / E E = P / I 2 P = I X R 2 P = E / R Apply the numbers from the above formulas to the Power wire calculation to determine the minimum gauge wire to properly supply the amplifier with current. KX1
Résumé du contenu de la page N° 18
Power Cable Calculation WW (Total RMS power output into 4 ) x 2 = (Total input wattage [Watts]) (Total input wattage) = (Maximum input current [Amps]) (Supply Voltage) WW Example: Amplifier with a rating of 100 watts per channel into 4 200 x 2 = 400 Watts (Total input power) 400 Watts / 12.5 Volts = 32 amps (Total maximum draw) Use this value of current draw to determine wire size from the chart below. Power Wire Chart Minimum Gauge wire Draw Up to 4 to 7 to 10 to 13 t
Résumé du contenu de la page N° 19
ELETRONICS LIMITED WARRANTY Kicker warrants this product to be free from defects in material and workmanship under normal use for a period of T TH HR RE EE E ((3 3)) M MO ON NT TH HS S from date of original purchase with receipt. When purchased from a Authorized KICKER Dealer it is warranted for T TW WO O ((2 2)) Y YE EA AR RS S from date of original purchase with receipt. In all cases you m mu us st t h ha av ve e the o or riig giin na all r re ec ce eiip pt t! Should service be neces- sary un
Résumé du contenu de la page N° 20
P.O. Box 459 Stillwater, Oklahoma 74076 U.S.A. 405 624-8510 or www.Kicker.com
