Instruction d'utilisation Fender SPL-6000P

Résumé du contenu de la page N° 1

Power Amplifiers
From Fender Pro Audio
Owner's Manual for
SPL-6000
P/N 038866

Résumé du contenu de la page N° 2

OWNER'S MANUAL SPL-6000 TWO CHANNEL POWER AMPLIFIER SPL-6000 INTRODUCTION Your new Fender SPL-6000 Power Amplifier is In order to thoroughly understand the operation, designed to provide you with years of trouble-free features and functions of your power amplifier, service for both permanent and portable applica- please read and refer, as needed, to this owner's tions. Utilizing a unique proprietary cross coupled manual. By doing so, your amplifier is sure to pro- protection system, the SPL

Résumé du contenu de la page N° 3

DESCRIPTION OF FEATURES PROFESSIONAL STEREO POWER AMPLIFIER OFF OFF PEAK PEAK SPL 6000 ON ON LIMIT MIN MAX MIN MAX LIMIT POWER ELECTRONICS LEFT •CHANNEL A RIGHT•CHANNEL B A C C B A B D D 1. FRONT PANEL 2. REAR PANEL A - PEAK LED INDICATOR E & F - OUTPUT CONNECTORS The red Peak LED Indicator illuminates when the output volt- Each channel is provided with a single 1/4" phone jack (E) age of the amplifier reaches clipping (maximum output volt- and a pair of five-way binding posts (F) which will ag

Résumé du contenu de la page N° 4

E E I J IJ A PRODUCT OF: FENDER MUSICAL INSTRUMENTS CORP., SERIAL TYPE: PR200 CORONA, CA 91720 600 WATTS 8 OHM MINIMUM CAUTION: CHASSIS SURFACE HOT LOAD BRIDGED WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT 300 WATTS 300 WATTS TO RAIN OR MOISTURE 4 OHM MINIMUM 4 OHM MINIMUM MONO DUAL MONO BRIDGE ATTENTION: CAUTION: UTILISER UN TO REDUCE FUSIBLE DE THE RISK OF RECHANGE FIRE, REPLACE = (+)TIP 1/4" FOR MONO BRIDGE DE MEME FUSE WITH = (–) RING PHONE OPERTION,

Résumé du contenu de la page N° 5

BASIC CONNECTIONS and WIRING Power and audio signal cables are the most common Always use stranded wire for three reasons: sources of sound system failure. Well-made and carefully maintained cables are essential to the reliability of the 1) It is more flexible and less prone to metal fatigue breakage. entire system. If long speaker cables are required, make sure the wire is of sufficient size to transfer all of the avail- 2) If an end is nicked while insulation is being stripped for able ampli

Résumé du contenu de la page N° 6

The SPL-6000 is timed to turn on the speaker outputs CAUTION: NEVER use coiled cords for after the amplifier's power supply is fully charged up, thus speaker hookup, even in an emergency. preventing any turn-on noise. Timing of the amplifier's turn-on circuit is usually sufficient to accommodate all the Coiled guitar-type cords usually have higher internal resis- turn-on anomalies from other pieces of gear in a system, tance than the speakers themselves. This is due to the making it acceptable

Résumé du contenu de la page N° 7

SPECIFICATIONS DESIGNATION TYPE PR 200 OUTPUT POWER Stereo Continuous sine wave output power, both channels driven +/- 1dB, 20 Hz to 20kHz, THD < 0.03% 150 W into 8 Ω, each channel 300 W into 4 Ω, each channel MONO BRIDGE 300 W into 16 Ω 600 W into 8 Ω SINGLE CHANNEL DRIVEN @ 1 kHz, 1% THD 8 Ω 179W 4 Ω 312W POWER BANDWIDTH 10 Hz to 68 kHz (3 dB down from rated power at less than 0.1% THD) FREQUENCY RESPONSE +0 -3dB; 5 Hz to 68 kHz (at rated power, 8 Ω) RISE TIME Less than 5.2 µSec SLEW RATE Gre