Résumé du contenu de la page N° 1
powerone
AMPLIFIERS
p1-650.2 / p1-1050.2 / p1-1650.2
p1-650.4 / p1-1050.4 / p1-1650.4
p1-1050.1 / p1-2050.1 / p1-3050.1
p1-5050.5
Résumé du contenu de la page N° 2
POWERONE SERIES AMPLIFIERS Congratulations on the purchase of your brand new Crunch amplifier and thank you for your support! The PowerOne Series amplifiers have been designed to a very high level of performance, packed with features unavailable in many products within the same price category. All of the amplifiers have variable crossovers built in, with added touches such as subsonic filter/highpass filter, bass equalization and a bass remote control module for the mono amps that allows bas
Résumé du contenu de la page N° 3
WIRE GAUGE GENERAL INSTALLATION PROCEDURE System Design The success of any car stereo system relies on several factors, such as the system design, execution of the installation, and system setup. Please remember that any system is only as good as its weakest link. Please remember that higher power systems are not necessarily useful purely for high sound pressure levels, but also to establish a headroom capability, to reproduce musical peaks cleanly without distortion. Lower power amplifiers w
Résumé du contenu de la page N° 4
AMPLIFIER FEATURE DESCRIPTIONS POWERONE AMPLIFIERS: Each model is capable of 4 & 2-Ohms stereo per channel, or 4-Ohms mono bridged operation except the mono amps All Crunch amplifiers feature a comprehensive diagnostic system, with speaker lead short circuit, and amplifier DC which are capable of 4, 2 and 1-Ohm loads. faults indicated by the red “PROTECT” LED. The input sensitivities for rated output powers are variable from 0.2V to 6V on all models. CAUTION: DO NOT OPERATE ANY AMPLIFIER BEL
Résumé du contenu de la page N° 5
+ - + - + - + - L L L L LEVEL BASS EQ HPF LPF X-OVER MODE LEVEL BASS EQ HPF LPF X-OVER MODE + - gnd - + + - gnd - + HI INPUT HI INPUT 6V 0.2V 0dB 9dB 60Hz 12KHz 30Hz 250Hz FULL LPF HPF MONO STEREO 6V 0.2V 0dB 9dB 60Hz 12KHz 30Hz 250Hz FULL LPF HPF MONO STEREO R R R R LINE OUT LINE INP
Résumé du contenu de la page N° 6
- + - -+ - + - + - + - -+ - + - + CHANNEL 1 / 2 CHANNEL 1 / 2 LINE OUT X-OVER LPF HPF BASS EQ LEVEL LINE INPUT LINE OUT X-OVER LPF HPF BASS EQ LEVEL MODE LINE INPUT MODE Ch2 Ch2 Ch4 Ch4 4 2 30Hz 250Hz 60Hz 12KHz 0dB 9dB 6V 0.2V 4 2 FULL LPF HPF 30Hz 250Hz 60Hz 12KHz 0dB 9dB 6V 0.2V FULL LPF HPF
Résumé du contenu de la page N° 7
- + - -+ - + - + + - + - L L CHANNEL 1 / 2 LEVEL BASS EQ HPF LPF X-OVER MODE LPF HPF BASS EQ LEVEL LINE INPUT LINE OUT X-OVER MODE + - gnd - + Ch2 Ch4 HI INPUT 4 2 6V 0.2V 0dB 9dB 60Hz 12KHz 30Hz 250Hz FULL LPF HPF MONO STEREO 30Hz 250Hz 60Hz 12KHz 0dB 9dB 6V 0.2V FULL LPF HPF LPF HPF BASS
Résumé du contenu de la page N° 8
REMOTE OUTPUT INPUT BASS SUB LOW LEVEL CONTROL BOOST SONIC PASS POWER L L PROTECT 0dB 9dB 15Hz 55Hz 40Hz 150Hz 6V 0.2V R R P1-1050.1 / P1-2050.1 / P1-3050.1 MONO AMPLIFIER APPLICATION Basic application These sub bass amplifiers can be used in any of the bi-amplification systems described in Crossover frequency control checklist: this manual, replacing the 2 channel amplifiers as per the illustrations. LOW PASS: 40Hz t
Résumé du contenu de la page N° 9
3/4 CH CONTROLS 1/2 CH CONTROLS CH5 CH4 CH2 LEVEL HPF MODE LEVEL HPF REMOTE L 4CH 5CH FULL FULL HPF HPF 6V 0.2V 10Hz 150Hz 6V 0.2V 10Hz 150Hz X-OVER X-OVER R 15Hz 55Hz 6V 0.2V 0dB 12dB 30Hz 150Hz POWER CH5 CH3 CH1 LEVEL SUBSONIC BASS EQ LPF PROTECT 5 CH CONTROLS P1-5050.5 5-CHANNEL AMPLIFIER APPLICATION Basic application Here we show how to use the channel amplifier as straight forward discret
Résumé du contenu de la page N° 10
8 Hz Hz Hz Hz FULL HPF dB Hz Hz Hz Hz FULL HPF dB dB
Résumé du contenu de la page N° 11
SETTING UP SYSTEMS AFTER INSTALLATION FOR BEST PERFORMANCE P1-650.2 / P1-1050.2 / P1-1650.2 / P1-650.4 / P1-1050.4 / P1-1650.4 / P1-5000.5 General: At this point you are ready to get more specific on the settings for your amplifier. High Pass: -When in HPF operation, this setting acts as a low frequency cut off for your system reproduction. The point that you set it at cuts off any frequencies from reproduction beyond this point. The 12 o’clock position is a great starting point. EXAMPLE: If yo
Résumé du contenu de la page N° 12
TROUBLESHOOTING A SYSTEM The key to finding the problem in a misbehaving sound system is to isolate parts of that system in a logical fashion to track down the fault. Description of the PROTECT system built into all Crunch amplifiers The diagnostic system will shut down the amplifier, until reset by turning the head unit off, and back on. This state of affairs will be indicated by the front panel PROTECT LED lighting up under the following conditions: 1 - A sort circuit on the loudspeaker lead
Résumé du contenu de la page N° 13
Maxxsonics Limited Warranty As the manufacturer of Maxxsonics, MB Quart, Autotek, Crunch and Hifonics car audio products, Maxxsonics USA Inc. Warrants to the original consumer purchaser the amplifier to be free from defects in material and workmanship for one (1) Year from date of purchase. All other parts and accessories of the system are warrantied to be free from defects in material and workmanship for one (1) year from date of purchase. Maxxsonics will repair or replace at it’s option and f
Résumé du contenu de la page N° 14
PART#: S1111
