Résumé du contenu de la page N° 1
®
PR 15 D
Powered bi-amplified two-way speaker system
Operating
Manual
www.peavey.com
Résumé du contenu de la page N° 2
Intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. Intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION: Risk of electrical shock — DO NOT OPEN! CAUTION: To reduce the risk of electric shock, do not remove cover. No user serviceable parts insi
Résumé du contenu de la page N° 3
IMPORTANT SAFETY INSTRUCTIONS WARNING: When using electrical products, basic cautions should always be followed, including the following: 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any of the ventilation openings. Install in accordance with manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registe
Résumé du contenu de la page N° 4
ENGLISH ™ PR 15D ® Thank you for purchasing the class D powered PR 15D. The PR 15D features a bi-amped power section that provides 150 watts power ™ for the woofer and 50 watts power for the compression driver tweeter, both with Peavey-exclusive DDT compression. Featuring ™ a 15” heavy duty woofer and the RX 14 compression driver, the PR 15D provides an XLR and 1/4”phone combo jack, with mic/line switchable level, balanced input with volume control. Features • Bi-amplified Class D powered s
Résumé du contenu de la page N° 5
LINK DIRECT OUT IN GND LIFT MIC/LINE LEVEL POWER/CLIP Applications ® The Peavey PR 15D has a variety of applications such as sound reinforcement, public address, side fill system, karaoke or musical playback. With the optional monitor stand kit, the Peavey PR 15D makes an excellent stage monitor. A typical signal source for the line-level inputs of the Peavey PR 15D would be a sound reinforcement mixing console (mixer) or the output from a CD player, iPod player or tape deck. A dynamic micr
Résumé du contenu de la page N° 6
F R O N T P A N E L 5 4 6 6a 7 8 9 10 4 GROuND LIFT Switches the XLR (5) PIN 1 from direct contact with ground in the event that hum occurs. 5 PRIMARY INPuT (CHANNEL 1) The primary input is switchable between line-level and mic-level input. The line-level input is of the medium impedance balanced type, and when switched to mic-level(6) it is of a typical low-Z mic input impedance. Jack (5) is a combo female XLR and 1/4" TRS connector. 6 PAD Switches the sensitivity of Channel 1 from line-leve
Résumé du contenu de la page N° 7
O P E R A T I N G I N S T R u C T I O N S Cautions The unit must be disconnected from the AC power source before any work is done on it. Refer all servicing to qualified service personnel. The heat sink on the back plate can become hot to the touch. Do not block or cover the heat sink from ventilation. Be sure to keep the microphone away from the front of the speaker after switching the mic sensitivity pad to the OUT position and while setting the microphone level, or very loud feedback will
Résumé du contenu de la page N° 8
® Connecting AC Power To The PR 15D The PR 15D comes with an 8-foot IEC connection AC power cord. If you are using an extension cord or power strip with this powered speaker, make sure it is of good quality and of a sufficient current capacity to maintain safety and maximize the power output capability of the PR 15D. Do not connect any other device to the same extension cord that the PR 15D is connected to. Special Note for Permanent Installation When installing the PR 15D, AC power runs will
Résumé du contenu de la page N° 9
level controls all the way down, and bring them up slowly with the PR 15D volume control set to the desired setting (halfway up recommended to start). Mic/Line Pad Adjustment The mic/line pad (6) provides for the increased gain needed for microphone use into the primary input (5). Use a straightened paperclip or small screwdriver to reach through the hole in the rear panel where the recessed tab is to set its position. Set the Mic/Line Pad to “in,” or the white tab furthest from the panel,
Résumé du contenu de la page N° 10
If an extension cord is being used to provide the AC power to the unit, ensure that it is of sufficient current capacity and that it is not also being used to supply power to any other device. The PR 15D has built-in EQ to extend and smooth the natural response of the speakers in the system. Bass boost and HF EQ have been applied and the system has a nominally flat response, so it should require little, if any, additional EQ. If excessive additional bass boost or HF boost have been added ex
Résumé du contenu de la page N° 11
The system power amplifiers shall have an unfiltered frequency response of 10 Hz to 30 kHz which deviates no more than +0, -1 dB up to rated power, a damping factor greater than 100 @ 1 kHz into 8 ohms, hum and noise better than 90 dB below rated power, and THD and IMD of less than 0.1%. The woofer amplifier shall be capable of 150 W into a 8 ohm nominal load, and the tweeter amplifier shall be capable of 50 W output into a 8 ohm load, and both shall incorporate independent DDT™ compression.
Résumé du contenu de la page N° 12
® Peavey PR 15D SPECIFICATIONS Crossover Slopes: Additional Remarks: Enclosure: Peavey PR 15D 18 dB/octave (third order) low pass, Also available as a passively crossed- (domestic) 18 dB/octave (third order) high pass, over unit, the Peavey PR 15. Frequency Response: both with staggered poles and driver 47 Hz to 20 kHz EQ. Unit has horn spatially aligned ELECTRONICS AND AMPLIFIER with woofer. SPECIFICATIONS: Low Frequency Limit (-3 dB point): 36 Hz Electronic Input Impedance Electro
Résumé du contenu de la page N° 13
FREquENCY RESPONSE CuRVES Amplitude Response (1m On-Axis) 110 100 90 80 70 60 20 50 100 200 500 1k 2k 5k 10k 20k Frequency (Hz) Figure 1 13 dB SPL (re 20 Pa)
Résumé du contenu de la page N° 14
NOTES: 14
Résumé du contenu de la page N° 15
PEAVEY ELECTRONICS CORPORATION LIMITED WARRANTY Effective Date: september 5, 2007 What This Warranty Covers Your Peavey Warranty covers defects in material and workmanship in Peavey products purchased and serviced in the U.S.A. and Canada. What This Warranty Does Not Cover The Warranty does not cover: (1) damage caused by accident, misuse, abuse, improper installation or operation, rental, product modification or neglect; (2) dam- age occurring during shipment; (3) damage caused by repair or ser
Résumé du contenu de la page N° 16
Features and specifications subject to change without notice. Peavey Electronics Corporation • 5022 Hartley Peavey Drive • Meridian • MS • 39305 (601) 483-5365 • FAX (601) 486-1278 • 80305569 • www.peavey.com ©2008
