Résumé du contenu de la page N° 1
TS16G~64GCF400
TS16G~64GCF400 400X CompactFlash Card
TS16G~64GCF400
Features
Description
• CompactFlash Specification Version 4.1 Compliant
Dedicated to fulfill the demanding requirements of
• RoHS compliant products
performance-conscious photographers, Transcend
• Single Power Supply: 3.3V ± 5% or 5V ± 10%
proudly releases its Extreme 400X CompactFlash
o o
• Operating Temperature: -25 C to 85 C
cards. With its amazing performance, the Transcend
o
Résumé du contenu de la page N° 2
TS16G~64GCF400 TS16G~64GCF400 400X CompactFlash Card TS16G~64GCF400 Specification Interface Specification Drivers No Device Driver Required ATA/ATAPI 7 PIO Mode 0 - 6 ATA Compatibility Multiword mode 0 - 4 UDMA Mode 0 - 6 Physical Specification Form Factor Compact Flash Card Storage Capacities 16 GB to 64 GB Length 36.40 ± 0.15 Dimensions (mm) Width 42.80 ± 0.10 Height 3.30 ± 0.10 Environmental Specifications Operating Temperature -25 ℃ to 85
Résumé du contenu de la page N° 3
TS16G~64GCF400 TS16G~64GCF400 400X CompactFlash Card TS16G~64GCF400 Performance Model P/N Capacity Read(MB/s) Write(MB/s) Random Read (MB/s) Random Write (MB/s) TS16GCF400 16GB 83.67 44.96 82.38 8.671 TS32GCF400 32GB 86.16 45.82 85.09 10.99 TS64GCF400 64GB 88.87 39.67 88.48 10.59 Note : 25 ℃ , according to IDE to CF card transferring board test on ASUS P4S800-MX, 1GB RAM, IDE interface support ® UDMA6, Windows XP Version 2002 SP2, CrystalDiskMark, copied
Résumé du contenu de la page N° 4
TS16G~64GCF400 TS16G~64GCF400 400X CompactFlash Card TS16G~64GCF400 Block Diagram Transcend Information Inc. 4 V1.0
Résumé du contenu de la page N° 5
TS16G~64GCF400 TS16G~64GCF400 400X CompactFlash Card TS16G~64GCF400 Transcend Information Inc. 5 V1.0
Résumé du contenu de la page N° 6
TS16G~64GCF400 TS16G~64GCF400 400X CompactFlash Card TS16G~64GCF400 Pin Assignments and Pin Type PC Card Memory Mode PC Card I/O Mode True IDE Mode4 Pin Signal Pin Signal Pin In, Out Pin Signal Pin In, Out In, Out Type Pin Num Num Name Type Name Type Type Num Name Type Type 1 GND Ground 1 GND Ground 1 GND Ground 2 D03 I/O I1Z, OZ3 2 D03 I/O I1Z, OZ3 2 D03 I/O I1Z, OZ3 3 D04 I/O I1Z, OZ3 3 D04 I/O I1Z, OZ3 3 D
Résumé du contenu de la page N° 7
TS16G~64GCF400 TS16G~64GCF400 400X CompactFlash Card TS16G~64GCF400 PC Card Memory Mode PC Card I/O Mode True IDE Mode4 Pin Pin In, Out Pin Pin In, Out Pin Pin In, Out Signal Name Signal Name Signal Name Num Type Type Num Type Type Num Type Type 7 -HIOE -HIOE -HIOE 10 10 8 34 HSTROBE I I3U 34 HSTROBE I I3U 34 I I3Z HSTROBE 11 11 9 HDMARDY -HDMARDY -HDMARDY 7 -IOWR -IOWR -IOWR 35 I I3U 35 I I3U 35 I I3Z 10,11 10,11
Résumé du contenu de la page N° 8
TS16G~64GCF400 TS16G~64GCF400 400X CompactFlash Card TS16G~64GCF400 Input Leakage Current Note: In Table 1 below, x refers to the characteristics described in table 2. For example, I1U indicates a pull-up resistor with a type 1 input characteristic. Table 1: Input Leakage Current Type Parameter Symbol Conditions MIN TYP MAX Units IxZ Input Leakage Current IL Vih = Vcc / Vil = Gnd -1 1 μA IxU Pull-Up Resistor RPU1 Vcc = 5.0V 50k 50
Résumé du contenu de la page N° 9
TS16G~64GCF400 TS16G~64GCF400 400X CompactFlash Card TS16G~64GCF400 Output Drive Characteristics Table 4: Output Drive Characteristics Type Parameter Symbol Conditions MIN TYP MAX Units Vcc Voh Ioh = -4 mA -0.8V 1 Output Voltage Volts Gnd Vol Iol = 4 mA +0.4V Vcc Voh Ioh = -4 mA -0.8V 2 Output Voltage Volts Gnd Vol Iol = 4 mA +0.4V Vcc Voh Ioh = -4 mA -0.8V 3 Output Voltage Volts Gnd Vol Iol = 4 mA +0.4V Tri-State Le
Résumé du contenu de la page N° 10
TS16G~64GCF400 TS16G~64GCF400 400X CompactFlash Card TS16G~64GCF400 Signal Description Signal Name Dir. Pin Description A10 – A00 I 8,10,11,12, These address lines along with the -REG signal are used to select the following: (PC Card Memory Mode) 14,15,16,17, The I/O port address registers within the CompactFlash Storage Card , the 18,19,20 memory mapped port address registers within the CompactFlash Storage Card, a byte in the card's information stru
Résumé du contenu de la page N° 11
TS16G~64GCF400 TS16G~64GCF400 400X CompactFlash Card TS16G~64GCF400 Signal Name Dir. Pin Description These input signals are used both to select the card and to indicate to the card -CE1, -CE2 I 7,32 whether a byte or a word operation is being performed. -CE2 always accesses (PC Card Memory Mode) the odd byte of the word.-CE1 accesses the even byte or the Odd byte of the Card Enable word depending on A0 and -CE2. A multiplexing scheme based on A0,-CE1, -
Résumé du contenu de la page N° 12
TS16G~64GCF400 TS16G~64GCF400 400X CompactFlash Card TS16G~64GCF400 Signal Name Dir. Pin Description -INPACK O 43 This signal is not used in this mode. (PC Card Memory Mode except Ultra DMA Protocol Active) The Input Acknowledge signal is asserted by the CompactFlash Storage Card -INPACK when the card is selected and responding to an I/O read cycle at the address (PC Card I/O Mode except Ultra that is on the address bus. This signal is used by the h
Résumé du contenu de la page N° 13
TS16G~64GCF400 TS16G~64GCF400 400X CompactFlash Card TS16G~64GCF400 Signal Name Dir. Pin Description -IOWR This signal is not used in this mode. I 35 (PC Card Memory Mode– Except Ultra DMA Protocol Active) The I/O Write strobe pulse is used to clock I/O data on the Card Data bus into -IOWR the CompactFlash Storage Card controller registers when the CompactFlash (PC Card I/O Mode –Except Ultra Storage Card is configured to use the I/O interface. DM
Résumé du contenu de la page N° 14
TS16G~64GCF400 TS16G~64GCF400 400X CompactFlash Card TS16G~64GCF400 Signal Name Dir. Pin Description This signal is used during Memory Cycles to distinguish between Common -REG I 44 Memory and Register (Attribute) Memory accesses. High for Common Memory, (PC Card Memory Mode– Except Low for Attribute Memory. Ultra DMA Protocol Active) Attribute Memory Select In PC Card Memory Mode, when Ultra DMA Protocol is supported by the host and the host has enab
Résumé du contenu de la page N° 15
TS16G~64GCF400 TS16G~64GCF400 400X CompactFlash Card TS16G~64GCF400 Signal Name Dir. Pin Description -VS1 Voltage Sense Signals. -VS1 is grounded on the Card and sensed by the Host O 33 -VS2 so that the CompactFlash Storage Card CIS can be read at 3.3 volts and -VS2 is 40 (PC Card Memory Mode) reserved by PCMCIA for a secondary voltage and is not connected on the Card. -VS1 This signal is the same for all modes. -VS2 (PC Card I/O Mode) -VS1 This
Résumé du contenu de la page N° 16
TS16G~64GCF400 TS16G~64GCF400 400X CompactFlash Card TS16G~64GCF400 Electrical Specification The following tables indicate all D.C. Characteristics for the CompactFlash Storage Card. Unless otherwise stated, conditions are: Vcc = 5V ±10% Vcc = 3.3V ± 5% Absolute Maximum Conditions DC Characteristics CompactFlash Interface I/O at 5.0V Parameter Symbol Min. Max. Unit Remark Supply Voltage V 4.5 5.5 V CC High level output voltage V V ─ ── ─ 0.8
Résumé du contenu de la page N° 17
TS16G~64GCF400 TS16G~64GCF400 400X CompactFlash Card TS16G~64GCF400 Input Power Input Characteristics for UDMA mode >4 In UDMA modes greater than 4, the following characteristics apply. Voltage output high and low values shall be met at the source connector to include the effect of series termination. Table: Input Characteristics (UDMA Mode > 4) Parameter Symbol MIN MAX Units DC supply voltage to drivers V 3.3 –8% 3.3% + 8% Volts DD3 Low to high
Résumé du contenu de la page N° 18
TS16G~64GCF400 TS16G~64GCF400 400X CompactFlash Card TS16G~64GCF400 Signal Interface Electrical specifications shall be maintained to ensure data reliability. Additional requirements are necessary for Advanced Timing Modes and Ultra DMA modes operations. See next sections for additional information. 10 10 Item Signal Card Host -CE1 Pull-up to V 500 K Ω ≧ R ≧ 50 K Ω and CC -CE2 shall be sufficient to keep inputs inactive Control Signal -REG when th
Résumé du contenu de la page N° 19
TS16G~64GCF400 TS16G~64GCF400 400X CompactFlash Card TS16G~64GCF400 state and 100 μ A high state, including pull-up resistor. The card shall be able to drive at least the following load 10 while meeting all AC timing requirements: 50 pF at a DC current of 400 μ A low state and 100 μ A high state. 4) Status Signals: the socket shall present a load to the card no larger than 50 pF at a DC current of 400 μ A low 10 state and 100 μ A high state, including pull-up
Résumé du contenu de la page N° 20
TS16G~64GCF400 TS16G~64GCF400 400X CompactFlash Card TS16G~64GCF400 Ultra DMA Electrical Requirements Host and Card signal capacitance limits for Ultra DMA operation The host interface signal capacitance at the host connector shall be a maximum of 25 pF for each signal as measured at 1 MHz. The card interface signal capacitance at the card connector shall be a maximum of 20 pF for each signal as measured at 1 MHz. Series termination required for Ul