Résumé du contenu de la page N° 1
VR61
VR62
Passive Full-Range Loudspeakers
INSTRUCTION MANUAL
Résumé du contenu de la page N° 2
1. SAFETY INSTRUCTIONS The exclamation point within an 1. Read these instructions. equilateral triangle is intended to alert the user of the presence of 2. Keep these instructions. important operating and maintenance 3. Heed all warnings. (servicing) instructions in the literature accompanying the apparatus. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with
Résumé du contenu de la page N° 3
14. Rigging Precautions: When mounting or suspending EAW Commercial loudspeaker enclosures, it is essential that load ratings, rigging techniques, and special safety considerations be appropriate for the installation. Use only the mounting/rigging points on the loudspeaker enclosure intended for this purpose. The user must determine the load requirements, dynamic loading, and any other contributing factors affecting the loudspeaker installation. The user must determine the proper design fac
Résumé du contenu de la page N° 4
2. INTRODUCTION Congratulations on the purchase of your new EAW Commercial loudspeaker. You now own one of the finest professional audio products available – the result of exceptional engineering and meticulous craftsmanship. Please read these instructions to get the maximum performance from your new loudspeaker. Each EAW Commercial loudspeaker is intended for professional use. The construction, components, and hardware have been designed to provide robust, reliable performance for its inte
Résumé du contenu de la page N° 5
1/4 INCH FLAT WASHER BRACKET/WALLMOUNT SCREW 1/4 INCH-20 2 PLACES X 1.25 INCH LONG HEX HEAD 2 PLACES 1/4 INCH LOCK WASHER 2 PLACES 3. INSTALLATION Unpacking and Inspection Visually inspect the outside of the shipping carton and check for any damage. After unpacking, if you find concealed damage to the loudspeaker, save the packing materials for the carrier’s inspection, notify the carrier immediately, and file a shipping damage claim. REMOVE SCREWS FROM BOTH SIDES Although EAW Commer
Résumé du contenu de la page N° 6
Mounting Instructions 1. Remove the screw from each end of the enclosure as shown below. 2. Align the bracket slots with the mounting holes on each end of the enclosure. Make sure the four openings in the bracket arms face upward. 3. Onto each of the two supplied hex-head screws, place a lock washer, and a flat washer. Thread them at least three complete turns into both of the enclosure’s side mounting holes, and tighten them securely. 4. The bracket /enclosure assembly may be mounted vertica
Résumé du contenu de la page N° 7
Bracket Dimensions VR61 10.00"(254) VR62 16.00"(406.4) 0.40" x 2.25" Full radius (10.16 x 57.15) 3.00"(76.2) 0.13"(3.3) 8.00"(203.2) 11.50" MOUNTING POINT, (292.1) 1/4-20 THREADED HOLE. (151.7) 62.2 2.00"(50.8) C L VR61 15.69"(398.5) 0.31" x 1.38" Full radius VR62 22.44"(570.0) (7.87 x 35.05) NOTE: Dimensions are in inches, Dimensions in brackets are mm 16.4 Tolerance ± 0.03"(0.8 mm) 270.4 Horn Rotation Instructions 115.8 • The high frequency horn can be rotated through 90 degrees to allo
Résumé du contenu de la page N° 8
4. CONNECTIONS WARNING: To prevent the risk of electric shock, do not connect the loudspeaker with the amplifier switched on. The protective cover over the terminal strip is a safety feature per CE requirements. Replace this cover after making the signal connections. 1. Remove the insulating cover from the loudspeaker input terminal strip. 2. The positive (+) input terminal of the loudspeaker connects to the positive (+) output of your power amplifier. -- + 3. The negative (–) terminal of t
Résumé du contenu de la page N° 9
Precautions • To prevent inductive phenomena causing humming or distortion, the speaker cables should not be run together with electrical energy conductors, microphone cables, or line-level audio lines. • Use speaker cables that have markings to distinguish the polarity, such as insulation or conductors of different colors. • Before using the loudspeaker, carefully check that all the connections have been made correctly to make sure there are no accidental short circuits that could cause el
Résumé du contenu de la page N° 10
5. OPERATION Signal Processing Sometimes external signal processing is desirable to “voice” the loudspeaker to accommodate particular program material, less than optimum acoustics, feedback control, or personal taste. For these purposes, use a suitable electronic signal processor. This can be as simple as a 1/3 octave graphic equalizer or a fully capable DSP (digital signal processor) such as the EAW Commercial DX810, or the EAW MX8750. Choosing a Power Amplifier There is no exact answer to
Résumé du contenu de la page N° 11
6. SPECIFICATIONS Model VR61 VR62 Woofer 6” x 1 6” x 2 C L Woofer Loading Baffle, sealed Baffle, sealed TOP DIMENSIONS APPLY Tweeter 1” exit 1” exit TO TOP AND BOTTOM Compression Compression D Tweeter Loading 60 x 90 Horn 60 x 90 Horn 4.56 in 115.8 mm Operating Range 85 Hz - 20 kHz 80 Hz - 20 kHz (-10 dB) 20˚ Horizontal Beamwidth 90 degrees 90 degrees - Nominal (rotatable) W Vertical Beamwidth 60 degrees 60 degrees - Nominal (rotatable) Axial Sensitivity 90 dB 92 dB (whole space SPL) 85 Hz to
Résumé du contenu de la page N° 12
PERFORMANCE GRAPHS VR61 Impedance vs Frequency VR62 Impedance vs Frequency 100 100 10 10 1 1 10k 20k 10 100 1000 10k 20k 10 100 1000 Frequency (Hz) Frequency (Hz) VR61 Axial Response vs Frequency VR62 Axial Response vs Frequency 120 120 110 110 100 100 90 90 80 80 70 70 60 60 10 100 1000 10k 20k 10 100 1000 10k 20k Frequency (Hz) Frequency (Hz) VR61 Beamwidth vs Frequency VR62 Beamwidth vs Frequency 360 360 100 100 10 10 Horizontal Horizontal Vertical Vertical 1 1 100 1000 10k 20k 100 1000 10k 2
Résumé du contenu de la page N° 13
7. TROUBLESHOOTING Loudspeaker difficulties usually fall into one of the following categories. The causes for each are listed in the most likely order of probability. No Sound or Low Output • Loudspeaker cables or connectors are not wired correctly or are faulty. Check all cabling, referring to these instructions for the correct connections. The best way to check a suspect cable is to swap it with a known good cable. Check the loudspeaker’s input panel to verify correct cable connections. •
Résumé du contenu de la page N° 14
8. SERVICE and MAINTENANCE Maintenance Usually, your EAW Commercial loudspeaker will not require regular maintenance for normal use. However, you can do several things to keep your loudspeaker in good operating and cosmetic condition. • Testing: Periodically test your loudspeaker for proper performance. A simple test is to play a CD through it using well-defined, articulate, wide-range program material. Listen to ensure all drivers are working properly and for any evidence of distortion or
Résumé du contenu de la page N° 15
5. Tech Support will tell you where to ship the unit when you call for a Service Request Number. We suggest insurance for all forms of cartage. EAW Commercial Technical Support Phone (USA/Canada) 888-337-7404 Phone 425-892-6503 Fax 425-485-1152 Address One Main Street Whitinsville, MA 01588 Web site www.eawcommercial.com e-mail support@eawcommercial.com 9. WARRANTY
Résumé du contenu de la page N° 16
EAW Commercial | One Main Street | Whitinsville, MA 01588 USA TEL toll free within US/Canada 888.337.7404 | TEL outside US 425.892.6503 | FAX 425.485.1152 www.eawcommercial.com © 2004 LOUD Technologies Inc. All Rights Reserved. EAW Commercial is a registered trademark of LOUD Technologies Inc.
