Résumé du contenu de la page N° 1
Satellite Speaker
Mounts - 1 Pair
Quick Installation Guide
Introducing the Satellite Speaker
The Satellite Speaker Mounts - 1 Pair are fully-adjustable
(Tilt, Swivel, & Pivot) speaker wall or ceiling mounts.
Key Features and Benefits
• Universal design fits most speaker brands & designs
Ceiling or wall mountable & compatible with 1, 2,
or 4-hole and key-hole speaker mounting (with
included adapters)
Allows customizable tilt, swivel, & pivot angle
adjustments for optimal speaker positioning
Résumé du contenu de la page N° 2
Package Contents (2) Speaker mounts (2) 1-hole adapters (2) 2/4-hole adapters (2) 2 ¼” ceiling mount extensions Mounting hardware Quick installation guide Mounting Hardware M6x20mm Machine Screw M5 x 20mm Machine Screw 8-32 x 5/8" Machine Screw 1/4"-20 x 1/2" Machine Screw M5 x 1/8" Plastic Screw 8-32 Round Key hole Nut #8 x 3/4" Self Tapping Screw #12 x 3/4" Self Tapping Screw #12 x 1-3/2" Self Tapping Screw #12-14 Alligator Anchor M4 x 8mm Flat Head Machine Screw 2
Résumé du contenu de la page N° 3
Installation Please read the instructions prior to installation. This speaker mount is designed solely for the mounting of small speakers weighing less than 8lbs. We are not responsible for damage that may occur if speakers weighing more than 8lbs. are used. The user will have to determine which type of configuration will work best with the included mounting hardware. If the included hardware does not fit with the application, the appropriate hardware will have to be purchased. Single Hole Mo
Résumé du contenu de la page N° 4
2. Once the proper configuration is determined, secure the post to the speaker. 3. Some speakers use the smaller M4 x 8 screw, which is inserted into the off-center on the mounting post, see Figure 2 below. M4 x 8mm Flat Head Machine Screw Back Speaker Figure 2 4. Check the size of the hole, make sure you have the 5/8"-32 x 5/8" machine screw, the 1/4"-20 x 1/2" machine screw, the M6 x 20mm, or the M5 x 20mm fits inside, see Figure 3 below. M5 x 1/8" Plastic Washer Back Speaker 5/8"-32x5/8" Mach
Résumé du contenu de la page N° 5
5. When the correct size is determined, place the screw through the speaker post and attach to the rear of the speaker enclosure. If the screw does not tighten properly, use the M5 x 1/8" plastic washer to tighten it up. Key Hole Mounting 1. If your speaker has a factory key hole design, you will use the 5/8"-32 x 5/8" machine screws in combination with the key hole nut. 2. Loosely pre-assemble the mounting post with the 5/8"-32 x 5/8" machine screw and key hole nut, see Figure 4 below. Be su
Résumé du contenu de la page N° 6
3. Engage the key hole nut into the key hole slot. 4. Put tension on the assembly by gently pulling back on the speaker mount post while tightening the 5/8"-32 x 5/8" machine screw, see Figure 4 on page 5. 5. The key hole nut will engage on the housing in the key hole slot. 6. If the post does not tighten securely against the housing, it will be necessarry to use the M5 x 1/8" plastic washer as a spacer under the head of the 5/8"-32 x 5/8" machine screw, see Figure 4 on page 5. 2/4 Hole Mounting
Résumé du contenu de la page N° 7
Back 1/4"-20 x 1/2" Speaker Machine Screw 4-Hole Orientation 2-Hole Orientation Figure 5 Self-Tapped Mounting 1. Locate the optimum location for the mounting plate and use it as template to mark the drilling locations. Do not drill or screw into the speaker where you could possibly damage the internal components. 2. Drill the pilot hole(s) using a 1/8" drill bit. The holes(s) should not be drilled more than 1/2" depth, see Figure 6 on the next page. 7
Résumé du contenu de la page N° 8
ST5.5 x 19 Self Back Speaker Tapping Screw Figure 6 Mounting to the Wall or Ceiling The mounting hardware for the three different surface applications is supplied. You will need to determine what style hardware will work best with your mounting surface. Always use caution when drilling into a wall or ceiling. Make sure to avoid all electrical and water lines. Wood Surface 1. Using a stud finder, locate the wood stud or framing member. Always mount the speakers in the center of a stud. 2. Using
Résumé du contenu de la page N° 9
ST5.5 c 45 Self Tapping Screw Figure 7 3. Drill holes through the drywall and into the wood stud using a 1/8" drill bit. These holes should be drilled 1-7/8" deep, see Figure 7 above. 4. After the holes are drilled, mount the wall plate using the self tapping screws. Drywall Surfaces 1. Locate the best mounting location in the ceiling or wall. Using the wall plate as a template, mark the hole positions on the mounting surface. For in-wall applications, position the mounting holes in a vertical
Résumé du contenu de la page N° 10
4. With the anchors in place, mount the wall plates using the ST5.5 x 45 self tapping screws, see Figure 8 below. ST5.5 x 45 Self Pre Drill 5/16" Tapping Screw Holes Insert screw through wall plate Insert Alligator and into the alligator anchor Anchor Figure 8 Concrete Surface 1. Using the wall plate as a template, mark hole positions on the mounting surface. For in-wall applications, position the mounting holes in a vertical pattern, see Figure 9 on the next page. 2. Drill holes in the solid c
Résumé du contenu de la page N° 11
Insert Alligator Anchor ST5.5 x 45 Self Tapping Screw Insert screw through wall plate and into the alligator anchor Using the hammer to tap anchor into place Figure 9 3. With the wall anchor in place, mount the wall plate using the ST5.5 x 45 self tapping screws, see Figure 9 above. Extension Mounting This is for ceiling and/or shelf applications. Do not use extension in the wall application. 1. Install 2-1/2" extension portion of the speaker mount to the wall place. 2. Secure the setscrew to ho
Résumé du contenu de la page N° 12
Low-Profile Mounting This is for wall and ceiling application. 1. Install the low-profile portion of the speaker mount to the wall plate or 2-1/2" extension. 2. Secure the setscrew to hold the extension in place with the weight of the speaker attached. Tighten the allen screw using the provided allen wrench. Figure 11 Speaker Mounting 1. Install the speaker with the speaker post or 2-hole plate attached. 2. Secure the screw to hold the extension in place with the weight of the speaker attached P
Résumé du contenu de la page N° 13
Blank Page 13
Résumé du contenu de la page N° 14
Blank Page 14
Résumé du contenu de la page N° 15
Technical Support and Warranty QUESTIONS? SIIG’s Online Support has answers! Simply visit our web site at www.siig.com and click Support. Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also submit questions online and a technical support analysts will promptly respond. SIIG offers a 5-year manufacturer warranty with this product. Please see our web site for more warranty details. If you encoun
Résumé du contenu de la page N° 16
About SIIG, Inc. Founded in 1985, SIIG, Inc. is a leading computer upgrade manufacturer of I/O connectivity products, including PCI & ISA serial and parallel ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b), networking, sound cards, and other accessories. SIIG is the premier one-stop source of upgrades. SIIG products offer comprehensive user manuals, many user-friendly features, and are backed by an extensive manufacturer warranty. High-quality control standards are evident by
