Instruction d'utilisation JL Audio SB-F-EXPDCNSL

Résumé du contenu de la page N° 1

®
Stealthbox
INSTALLATION GUIDE START
HERE
for the
SB-F-EXPDCNSL/10W3v2
(2003-Up Ford Expedition, without
➔ ➔ ➔
AdvanceTrac®)
*Caution* You may be working on a Expedition STEP 2: Using an 8mm socket, remove the STEP 3: In the center console, remove the
that has side air bags, located in the front seats.We pair of bolts that are located on both sides of rubber liner. Using a 7mm socket, remove
do ask for the removal of these front seats. the enclosure, towards the rear. these four bolts.
Disconn

Résumé du contenu de la page N° 2

Cont. From Previous Page ➔ ➔➔➔ STEP 7: Pull up and remove the cup holders. STEP 8: Using a 10mm socket, remove e the bolt STEP 9: Once the wire harness is unsecured, dis- STEP 10: Tilt the console up from the rear.This that secures the wire harness. Also remove the pair connect the white plug. will expose another harness with a white plug., dis- Using a 7mm socket, remove the pair of bolts that of bolts that secure the console to the floor. connect. have been exposed. ➔➔ ➔ STEP 11: As the conso

Résumé du contenu de la page N° 3

Cont. From Previous Page ➔ ➔➔➔ STEP 15: Cut out the template that is found on STEP 16: Scribe cut lines on the front portion of STEP 17: Cut the black inner console, following STEP 18: With the rear portion of the black con- Page 6. Place this template across the rear portion the black inner console. Using the picture as a guide. the scribe lines. A jig saw, air saw or cutting wheel sole, now modified. Place the supplied pair of wash- of the black inner console. Mark the correct scribe Same side

Résumé du contenu de la page N° 4

Cont. From Previous Page ➔ ➔➔➔ STEP 23: Use a OEM bolt that was just removed At this time double check the woofer for proper STEP 25: Using a 7mm socket, secure the wire STEP 26: Place the front portion of the modified to plug the driver’s side bolt hole. operation. Also run speaker wire to the enclosures harness that was removed in STEP14. black inner console, in front of the enclosure. mounting location and connect to the terminal. Route the wire harness under the driver’s side of STEP 24: Pla

Résumé du contenu de la page N° 5

Cont. From Previous Page CONGRATULATIONS! INSTALL COMPLETE. ➔ ➔ ➔ Included Hardware: STEP 31: Taking the factory storage bucket, Cut to STEP 32: Secure the storage lid from STEP 6 (3) 3/8”-16x1” Hex Bolts allow for a new depth of only 3-1/8”, from the top and front passenger seat if you did remove. (3) 3/8” Split Lock Washers edge. *If you did remove the passenger’s front seat, recon- (3) 3/8” Flat Washers Secure into the console, from STEPS 4&5. nect all the wiring and then reconnect the batter

Résumé du contenu de la page N° 6

STEP 15: STEP 15(1): Cut straight edge, (A) STEP 15(2): Cut on the outside of the arch, (B) Position this template with the arch to the rear of the OEM inner console. The marking of left and right is your left and right, not the vehicles. (B) right side left side (A) (A) www.jlaudio.com SB-F-EXPDCNSL/10W3v2, JL AUDIO, Inc 2004 Page 6 Sheet SKU#011106 Revision6/30/2004