Résumé du contenu de la page N° 1
SX Gobo™
Snapshot
Ok on Dimmer
Outdoor OK
Sound Activated
DMX512
Master/Slave
115V/230V Switch
Replaceable Fuse
User Serviceable
Duty Cycle
USER MANUAL
th
Chauvet, 3000 N 29 Ct, Hollywood, FL 33020 U.S.A.
(800) 762-1084 – (954) 929-1115
FAX (954) 929-5560
www.chauvetlighting.com
Résumé du contenu de la page N° 2
TABLE OF CONTENTS 1. BEFORE YOU BEGIN................................................................................................................................ 3 WHAT IS INCLUDED......................................................................................................................................... 3 UNPACKING INSTRUCTIONS............................................................................................................................. 3 AC POWER ...............
Résumé du contenu de la page N° 3
1. BEFORE YOU BEGIN What is included 1 x SX Gobo™ EHJ 24V 250W Lamp 7 Replaceable Gobos Warranty Card User Manual Unpacking Instructions Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Notify the shipper immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling. Save the carton a
Résumé du contenu de la page N° 4
Safety Instructions Please read these instructions carefully, which includes important information about the installation, usage and maintenance of this product. Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet. Always make sure that you are connecting to the proper voltage, and that the line voltage you are connecting to is not higher than that stated on the decal or rear panel of the fixtu
Résumé du contenu de la page N° 5
2. INTRODUCTION Features High-output rotating gobo projector Interchangeable rotating color/gobos 6 metal gobos with 5 dichroic colors + white Dual spring clips for a single dichroic color Adjustable rotation speed 3-position switch: CW rotation Stop CCW rotation Fan cooled Product Overview Hanging Bracket Focusing Lens Lamp Alignment Screw Gobo Fuse Speed Knob Gobo Rotation Power Cord Switch Lamp Access Lamp Access Thumbscrew Thumbscrew Lamp Lamp Alignment Alignment S
Résumé du contenu de la page N° 6
3. SETUP Lamp You will need to install a lamp prior to the initial operation of the fixture. An 800W halogen lamp is included. Warning! When replacing the lamp, please wait 15 minutes after powering down to allow the unit to cool down! Always disconnect from main power prior to lamp replacement. Do not touch the envelope (glass area) of the bulb with bare hands. If this happens, clean the lamp with alcohol and wipe it with a lint free cloth before installation. Lamp Installation 1) Unscre
Résumé du contenu de la page N° 7
Lamp Alignment How-To Often, after a new installation of a lamp, you will find that there is an uneven field of light or what is refered to as a hot spot. This is due to the most intense point of the lamp source not being positioned optimally within the reflector. Lamp alignment screws There are three lamp alignment screws provided at the base of the fixture. Turning these screws allows you to optimize the projection quality of the spot as well as the overall intensity of the beam. E
Résumé du contenu de la page N° 8
Replacing Gobos 1) Open the top cover by removing the six screws indicated in figure A. 2) Remove the retaining spring using a Figure A flathead screwdriver (figure B). 3) Remove the gobo and replace with a new gobo. Note: The black side of the gobo should be facing the lamp. 4) Reinsert the retaining spring. Note: The two springs indicated in figure C can be used to hold gel inserts or dichroic glass. This is optional, and is not included with the SX Gobo. Figure B 5) Replace
Résumé du contenu de la page N° 9
Mounting ORIENTATION This fixture may be mounted in any position provided there is adequate room for ventilation. RIGGING Hanging Clamp It is important never to obstruct the fan or vents pathway. Mount the fixture using, a suitable “C” or “O” type clamp. Adjust the angle of the fixture by loosening both knobs and tilting the fixture. After finding the desired position, retighten both knobs. When selecting installation location, take into consideration lamp replacement access and rout
Résumé du contenu de la page N° 10
General Troubleshooting Applies to Foggers Dimmers Symptom Solution(s) Lights & Snow Controllers & Chaser Auto shut off Check fan thermal switch reset Beam is very dim or not Clean optical system or replace lamp bright Check 220/110v switch for proper setting Breaker/Fuse keeps Check total load placed on device blowing Chase is too slow Check users manual for speed adjustment Device has no power Check for power on Mains. Check device’s fuse. (internal and/or external) Fixture is no
Résumé du contenu de la page N° 11
Technical Support Address: Service Dept. 3000 N 29th Ct, Hollywood, FL 33020 (U.S.A.) Support (Email): tech@chauvetlighting.com Telephone: (954) 929-1115 - (Press 4) Fax: (954) 929-5560 - (Attention: Service) Website: http://www.chauvetlighting.com 5. APPENDIX General Maintenance To maintain optimum performance and minimize wear fixtures should be cleaned frequently. Usage and environment are contributing factors in determining frequency. As a general rule, fixtures should be cleaned
Résumé du contenu de la page N° 12
Claims Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and submit claims with the shipper in the event that a fixture is damaged due to shipping. Any other claim for items such as missing component/part, damage not related to shipping, and concealed damage, must be made within seven (7) days of receiving merchandise. Technical Specifications WE
