Résumé du contenu de la page N° 1
Product Manual
®
Momentus 5400.2 Blade
Server
ST9120821AB
ST9100824AB
ST98823AB
ST96812AB
ST94813AB
100367617
Rev. B
August 2007
Résumé du contenu de la page N° 2
©2004-2007, Seagate Technology LLC All rights reserved. Publication number: 100367617, Rev. B August 2007 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Momentus, Seagate- SeaBOARD, SeaFONE, SeaTDD, and SeaTools are either trademarks or registered trade- marks of Seagate Technology LLC or one of its affiliated companies in the United States and/ or other countries. All other trademarks or registere
Résumé du contenu de la page N° 3
Contents 1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1 Specification summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.2 Formatted capacity . . . . . . . . . . . . . . . . . .
Résumé du contenu de la page N° 4
ii Momentus 5400.2 Blade Server Product Manual, Rev. B
Résumé du contenu de la page N° 5
List of Figures Figure 1. Momentus 5400.2 PATA disc drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Figure 2. Typical 5V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Figure 3. Jumper settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Figure 4. Mounting dimensions—top, side and end view . . . . . . . . .
Résumé du contenu de la page N° 6
iv Momentus 5400.2 Blade Server Product Manual, Rev. B
Résumé du contenu de la page N° 7
1.0 Introduction ® This manual describes the functional, mechanical and interface specifications for the following Seagate ® Momentus 5400.2 Blade Server drives: � ST9120821AB � ST9100824AB � ST98823AB � ST96812AB � ST94813AB These drives provide the following key features: � 5,400-RPM spindle speed and 8-Mbyte buffer combine for superior performance. � Quiet operation. Fluid Dynamic Bearing (FDB) motor. � High instantaneous (burst) data transfer rates (up to 100 Mbytes per second) using Ultra D
Résumé du contenu de la page N° 8
2 Momentus 5400.2 Blade Server Product Manual, Rev. B
Résumé du contenu de la page N° 9
2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate ST9120821AB, ST9100824AB, ST98823AB, ST96812AB, and ST94813AB model drives. 2.1 Specification summary The specifications listed in this table are for quick reference. For details on specification measurement or definition, see the appropriate section of this manu
Résumé du contenu de la page N° 10
Table 1: Specifications Drive specification ST9120821AB ST9100824AB ST98823AB ST96812AB ST94813AB Average seek, read (msec typical) 12.5 Average seek, write (msec typical) 14.5 Full-stroke seek (msec) 22 (typical); 24 (max) Seek power (typical) 2.0 watts Read: 1.8 watts Read/write power (typical) Write: 1.8 watts Idle mode (typical) 0.80 watts Standby mode 0.26 watts (typical)** Sleep mode 0.26 watts (typical)** Voltage tolerance 5V ± 5% (including noise) 5° to 55°C (operating) Ambient tempe
Résumé du contenu de la page N° 11
Table 1: Specifications Drive specification ST9120821AB ST9100824AB ST98823AB ST96812AB ST94813AB 5 Years on distribution units. To determine the warranty for a specific drive, use a web browser to access the following web page: www.seagate.com/support/service/ Warranty From this page, click on the “Verify Your Warranty” link. You will be asked to provide the drive serial number, model number (or part number) and country of purchase. The system will display the warranty information for your d
Résumé du contenu de la page N° 12
2.5 Recording and interface technology Technology Specification Interface Parallel ATA Recording method RLL 0,11 Recording density BPI (bits/inch typical) 778k Track density TPI (tracks/inch typical) 126k 2 Areal density (Gbits/inch max) 98.2 Spindle speed (RPM) (± 0.2%) 5,400 Internal data-transfer rate OD (Mbytes/sec max) 42 I/O data-transfer rate (Mbytes/sec max) 100 (Ultra DMA mode 5) Interleave 1:1 Cache buffer 8 Mbytes (8,192 kbytes) 2.6 Physical characteristics Height (mm) 9.5 +/–0.2
Résumé du contenu de la page N° 13
2.7 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications below are defined as follows: � Track-to-track seek time is an average of all possible single-track seeks in both directions. � Average seek time is a true statistical random average of at least 5,000 measurements of seeks between random tracks, less overhead. Typical seek times (msec)* Read Write Track-to-track 1.0 1.5 Average 12.5 14.5
Résumé du contenu de la page N° 14
2.9 Power specifications The drive receives DC power (+5V) through the interface connector. 2.9.1 Power consumption Power requirements for the drives are listed in the table on page 8. Typical power measurements are based on an average of drives tested, under nominal conditions, using 5.0V input voltage at 25°C ambient temperature. • Spinup power Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed. � Seek mode During seek mode, the read/
Résumé du contenu de la page N° 15
2.9.1.1 Typical current profile Figure 2. Typical 5V startup and operation current profile 2.9.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +5 volt line. Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave injected noise at up to 10 MHz. Note. Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write current. 2.9.3 Volt
Résumé du contenu de la page N° 16
2.10 Environmental specifications 2.10.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Actual drive case temperature should not exceed 40°C (104°F) within the operating ambient conditions. Above 1,000 feet (305 meters), the maximum temperature is derated linearly by 1°C every 1000 feet. Operating 5° to 40°C (41° to 104°F) Nonoperating –40° to 70°C (–40° to 158°F) 2.10.2 Temperature gradient Operating 20°C per hour
Résumé du contenu de la page N° 17
2.10.5 Shock All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws. Shock may be applied in the X, Y or Z axis. 2.10.5.1 Operating shock These drives comply with the performance levels specified in this document when subjected to a maximum operating shock of 250 Gs based on half-sine shock pulses of 2 msec. Shocks should not be repeated more than two times per second. 2.10.5.2 Nonoperating shock The nonoperating shock leve
Résumé du contenu de la page N° 18
2.11 Acoustics Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All mea- surements are consistent with ISO document 7779. Sound power measurements are taken under essentially free-field conditions over a reflecting plane. For all tests, the drive is oriented with the cover facing upward. Note. For seek mode tests, the drive is placed in seek mode only. The number of seeks per second is defined by the following equation: (Number of seeks per secon
Résumé du contenu de la page N° 19
2.13 Reliability Measurement type Specification 14 Nonrecoverable read errors 1 per 10 bits read, max. Annualized Failure Rate (AFR) 1.74% at maximum case temperature of 40°C and 8,760 power on hours (POH). Load/Unload (U/UL) 25°C, 50% relative humidity 600,000 software-controlled power on/off cycles 20,000 hard power on/off cycles 32°C, 80% relative humidity 600,000 software-controlled power on/off cycles 5°C, 80% relative humidity 20,000 hard power on/off cycles 5°
Résumé du contenu de la page N° 20
Korean RRL If these drives have the Korea Ministry of Information and Communication (MIC) logo, they comply with para- graph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Radio Research Laboratory (RRL) Ministry of Information and Communication Republic of Korea. These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic Susceptibil- ity (EMI/EMS) for Cla
