Résumé du contenu de la page N° 1
®
DD14 Series
®
Intercept
Dome Drive
Installation/
Operation Manual
C458M-B (1/98)
Pelco • 3500 Pelco Way, Clovis • CA 93612-5699 USA • www.pelco.com
In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150
International Customers: Tel (1-559) 292-1981 or FAX (1-559) 348-1120
Résumé du contenu de la page N° 2
CONTENTS Section Page 1.0 GENERAL ..................................................................................................5 1.1 IMPORTANT SAFEGUARDS AND WARNINGS ............................... 5 1.2 UNPACKING INSTRUCTIONS ..........................................................6 2.0 DESCRIPTION ..........................................................................................7 2.1 MODELS ........................................................................................
Résumé du contenu de la page N° 3
LIST OF ILLUSTRATIONS Figure Page 1 Back Box and Dome Drive Components ...........................................9 2 Camera/Lens Wiring Diagram ........................................................... 10 3 Attaching Camera/Lens to Tilt Table ................................................. 11 4 Pan Limit Stops (Only Two Shown) ................................................... 12 5 24 VAC Back Box Wiring Diagram (For Dome Drives with Integral Receiver/Driver) ..............................
Résumé du contenu de la page N° 4
(This page intentionally left blank.) 4 Pelco Manual C458M-B (1/98)
Résumé du contenu de la page N° 5
1.0 GENERAL 1.1 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by Qualified Service Personnel and conform to all Local codes. 2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X ,6 or 6P enclosure, it is designed for Indoor use only and it must not be installed where exposed to rain and moisture. 3. Only use replacement parts recommended by Pelco.
Résumé du contenu de la page N° 6
1.2 UNPACKING INSTRUCTIONS Unpack and inspect all parts carefully. Be sure to save the shipping carton and any inserts. They are the safest material in which to make future shipments. If an item appears to have been damaged in shipment, replace it properly in its carton and contact the factory a t 1-800-289-9100 or 1-559-292-1981 for a replace- ment. (International customers fax 1-559-348-1120 for authorization and instruc- tions.) If an item needs to be returned to the factory for repair, cons
Résumé du contenu de la page N° 7
2.0 DESCRIPTION ® The DD14 Series of dome drives is part of the IDS14 Intercept Series of domes. The IDS14 Series is an integral system that includes a back box (BB14), dome drive (DD14), and dome receiver/driver (DRD14). This manual covers the DD14 Series of dome drives. For installation and operation instructions for the back box, refer to manual C454M-C; for the dome receiver/ driver, refer to 466M-E. 2.1 MODELS DD14B1L Dome drive with 355° pan rotation and fixed pan speed of 12° per second.
Résumé du contenu de la page N° 8
3.0 INSTALLATION Proceed with the installation of the dome drive after you have installed the back box. If a camera/lens package has not been installed on your dome drive, you can install the camera/lens either before you install the dome drive in the back box or after you install the dome drive. If you want to install the camera/lens first, proceed to Sec- tions 3.2, LENS WIRING, and 3.3, CAMERA/LENS INSTALLATION, then return to Section 3.1, DOME DRIVE INSTALLATION. 3.1 DOME DRIVE INSTALLATI
Résumé du contenu de la page N° 9
BACK BOX HAIRPIN CLIP LATCH HAIRPIN GUIDE PIN GUIDE PIN CLIP LATCH 25-PIN CONNECTOR DOME DRIVE UPPER BRACKET 25-PIN CONNECTOR LATCH PIN LATCH PIN BUSHING BUSHING Figure 1. Back Box and Dome Drive Components Pelco Manual C458M-B (1/98) 9
Résumé du contenu de la page N° 10
Figure 2. Camera/Lens Wiring Diagram 10 Pelco Manual C458M-B (1/98)
Résumé du contenu de la page N° 11
3.3 CAMERA/LENS INSTALLATION Install the camera/lens you have selected for use with the IDS14 series dome as follows: 1. Loosen the 1/4-20 lens support fastener (item 1 in Figure 3) and slide lens support down. 2. Attach camera/lens to the tilt table with the 1/4-20 x 3/4" bolt, flat washer, and lock washer (items 2 in Figure 3) that are provided. If the camera/lens can be balanced on the tilt table, the life of the dome drive will be extended. 3. Now slide the lens support up to the lens and,
Résumé du contenu de la page N° 12
3. Models with 355° Rotation Only - Adjust the pan limit stops: NOTE: The tilt limit stops are not adjustable. a. Pan the unit to the desired left position. b. Turn off the power. c. Position the limit stop and tighten it in place. Refer to Figure 4 for the location of the limit steps. Disconnect the drive from the back box, if nec- essary, to make the adjustment. CAUTION: Do not re- To remove the dome drive: move or reposition the 1. Remove the hairpin clips from the latches. fixed limit stop
Résumé du contenu de la page N° 13
4.0 MAINTENANCE Regularly scheduled maintenance will prolong the operational life and appearance of the equipment. Clean the dome with a nonabrasive cleaning cloth and antistatic cleaner that is safe for use on acrylic plastic. Do not use kerosene or similar substances that can scratch the surface. The dome drive should also be inspected and any dust and debris blown off. Pay special attention to the spur gear drives. After removing dust and debris a film of silicone lubricant should be applied
Résumé du contenu de la page N° 14
5.0 WIRING DIAGRAMS Figure 5. 24 VAC Back Box Wiring Diagram (For Dome Drives with Integral Receiver/Driver) 14 Pelco Manual C458M-B (1/98)
Résumé du contenu de la page N° 15
Figure 6. 120 VAC Back Box Wiring Diagram (For Dome Drives with Integral Receiver/Driver) Pelco Manual C458M-B (1/98) 15
Résumé du contenu de la page N° 16
Figure 7. 230 VAC Back Box Wiring Diagram (For Dome Drives with Integral Receiver/Driver) 16 Pelco Manual C458M-B (1/98)
Résumé du contenu de la page N° 17
Figure 8. Wiring Diagram for Dome Drives with 355° Rotation Pelco Manual C458M-B (1/98) 17
Résumé du contenu de la page N° 18
Figure 9. Wiring Diagram for Dome Drives with 360° Rotation 18 Pelco Manual C458M-B (1/98)
Résumé du contenu de la page N° 19
Figure 10. Wiring Diagram for Hard-Wire Systems Pelco Manual C458M-B (1/98) 19
Résumé du contenu de la page N° 20
6.0 EXPLODED ASSEMBLY DIAGRAMS 1 2 3 4 8 5 49 10 6 11 7 12 13 39 48 47 14 24 25 23 22 21 46 9 36 50 45 61 44 15 43 42 19 41 40 36 38 60 28 56 27 65 31 29 REMOVE BEFORE OPERATING 26 30 16 34 20 17 18 51 52 54 33 53 55 32 Figure 11. DD14 Series Dome Drive Exploded Assembly Mechanical Parts Diagram 20 Pelco Manual C458M-B (1/98)
