Résumé du contenu de la page N° 1
SPECO TECHNOLOGIES CVC-927PTZ DOME CAMERA
Instruction Manual
Please read this manual thoroughly before use and keep it handy for future reference.
Rev.040812
Résumé du contenu de la page N° 2
Warnings and Cautions WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECTS THROUGH THE VENTILATION GRILLS OR OTHER OPENINGS ON THE EQUIPMENT. CAUTION EXPLANATION OF GRAPHICAL SYMBOLS The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the pr
Résumé du contenu de la page N° 3
FCC COMPLIANCE STATEMENT FCC INFORMATION: THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANU
Résumé du contenu de la page N° 4
IMPORTANT SAFEGUARDS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that product heat. 9. Do not defeat the sa
Résumé du contenu de la page N° 5
Table of Contents Chapter 1 — Introduction ..............................................................1 1.1 Features..............................................................................................1 Chapter 2 — Installation and Configuration ..................................3 2.1 Package Contents ..............................................................................3 2.2 Basic Configuration Of Fastrax II E Dome Camera System ...............4 2.3 Setting Dome
Résumé du contenu de la page N° 6
3.7 Tour ..................................................................................................15 3.8 Pattern ..............................................................................................17 3.9 Alarm.................................................................................................18 3.10 Area Title.........................................................................................18 3.11 Privacy Zone .........................................
Résumé du contenu de la page N° 7
Dome Reset ...........................................................................................................30 System Information ................................................................................................30 Appendix A — Specifications.......................................................31 Appendix B — Troubleshooting...................................................34 Appendix C — Glossary ..............................................................35
Résumé du contenu de la page N° 8
Chapter 1 — Introduction 1.1 Features The Fastrax II E dome camera and the Fastrax II Keyboard Controller make up the building blocks for any surveillance/security system. Using multiple Keyboard Controllers and multiple dome cameras, no place is too large for monitoring. Extensible and flexible architecture facilitates remote control functions for a variety of external switching devices such as multiplexers and DVRs. • Built-in 18x(23x,25x) times optical power zoom camera wi
Résumé du contenu de la page N° 9
UP TO 255 MULTIPLEXER Alarm Input UP TO 8 UP TO 99 DVR Alarm Output UP TO 4 UP TO 32 CAMERA J-box Master Keyboard Figure 1 – Typical System Configuration push bubble ring ass'y remove camera window screw push remove window assemble bubble ring ass'y Figure 2 – Assemble bubble ring ass’y Note : It is recommended to remove camera window for improving picture quality when you use bubble ring ass’y. 2
Résumé du contenu de la page N° 10
Chapter 2 — Installation and Configuration 2.1 Package Contents The package contains the following. Fastrax II E (Dome Camera) ………………………1 Bubble Ring ………………………1 Instruction Manual (This Document) ………………………1 Assembly Screws for Attaching Fastrax II E ………………………3 Plastic Anchor ………………………3 10Pin Connector ………………………1 12Pin Connector ………………………2 CAUTION: Be sure to have caution labels(E version only) on both the body and the base of the camera. Different version will not
Résumé du contenu de la page N° 11
2.2 Basic Configuration of Fastrax II E Dome Camera System. POWER AC 24V STP AWG # 22 SIREN POWER AC 24V RS-485 HALF DUPLEX MODE : RX+,RX- LIGHT ALARM OUTPUT SENSOR UP TO 4 ALARM INPUT UP TO 8 ALARM INPUT ALARM INPUT 1~4 5~8 BNC ALARM OUTPUT ALARM OUTPUT 1~2 3~4 (RS-422) MONITOR RS-422 SIMPLEX MODE : (RX+),(RX-) DUPLEX MODE : (TX+),(TX-),(RX+),(RX-) BNC Figure 4– Basic installation diagram 4 AC+ AC- FGND (RX+) (RX+) (RX-) (RX-) DOME1 + RX+(TX+) RX+(TX+) RS-485 RX-(TX-) RX-(TX-) D
Résumé du contenu de la page N° 12
2 2 2 2 2 2 1 1 1 1 1 1 0 0 0 0 0 0 9 9 9 9 9 9 8 8 8 8 8 8 The dome camera must be installed by qualified service personnel in accordance with all local and federal electrical and building codes. The system should be installed according to Figures 4 through 9. Termination Switches SW1 ON KSD02H 1 2 9A Address(ID) and Protocol selection Switches S3 S6 S2 S5 S1 S4 Figure 5– Layout of Switches 2.3 Setting Dome Camera Termination The device which is connected at end of line, whether
Résumé du contenu de la page N° 13
Figure 7- Termination Diagram 6
Résumé du contenu de la page N° 14
2 2 2 1 1 1 0 0 0 9 9 9 8 8 8 2.4 Setting Dome Camera Address (ID) To prevent damage, each dome camera must have a unique address (ID). When installing multiple dome cameras using a multiplexer, it is suggested that the dome camera address match the multiplexer port number. If you want to set the address more than 999, you should contact the service provider. Example: Port 1 = Dome 1, Port 2 = Dome 2 … Port 16 = Dome 16. If more than 16 dome cameras are installed using two or more mu
Résumé du contenu de la page N° 15
2.5 Setting Dome Camera Protocol If a dome camera is to be installed with a Fastrax keyboard controller, select F2 protocol. Consult service personnel if a dome camera is installed with device other than a keyboard controller. S/W On Off FUNCTION NTSC PAL D1 S4-1 Enable Disable Alarm D2 S4-2 PAL NTSC NTSC/PAL S4 S4 D3 S4-3 Reserved D4 S4-4 RS-422 RS-485 RS-422/RS-485 D5 D6 D7 PROTOCOL S5-1 S5-2 S5-3 F2,F2E,P,D,E & Ph Protocol Off Off Off Camera (Default) S6 Off Of
Résumé du contenu de la page N° 16
2.6 Connections • Connecting to the RS485/ 422 The dome camera can be controlled remotely by an external device or control system, such as a control keyboard, using RS485 half-duplex , RS422 duplex or simplex serial communications signals. Connect Marked Rx+, Rx- to Tx+ and Tx- of the RS485 control system. If control system is RS422, connect Rx+(Tx+), Rx+(Tx-) and Rx+, Rx- of the dome camera to Tx+, Tx- and Rx+, Rx- of the control device respectively. • Connecting Video out connecto
Résumé du contenu de la page N° 17
RAM TEST CHECK NO. : OK! CHECK AAAA : OK! CHECK 5555 : OK! FASTRAX II E Vx.xxx CAMERA TYPE xxxx WAIT DOME SETTING. INIT TILT ORGIN SET OK INIT PAN ORGIN SET OK INIT CAMERA SET OK PRESET No. CAMERA TITLE 001 PRESET PRESET TITLE or AREA TITLE CAMERA ID INFORMATION EMPTY DATA ! DISPLAY FUNCTION T001 DOMEID:0001 UNDER RUNNING ALARM:1
Résumé du contenu de la page N° 18
Chapter 3 — Program and Operation 3.1 Dome Camera Selection Before you program or operate a dome camera, you must select the dome camera by pressing the dome camera No. + CAM Example: Pressing 1 , 0 and CAM key sequentially will select dome camera 10. The selected dome camera ID will be displayed on the LCD monitor of the keyboard controller. 3.2 Accessing the On-Screen Menu Utility You can call up the On-screen menu utility on your monitor by pressing MENU key on the keybo
Résumé du contenu de la page N° 19
3.3 How to control the On-Screen Menu Utility Action Function MENU Call the On-screen menu utility Go into the sub-menu items. Execute the command(exit) Joystick left or right Change value. Navigate through the menu items. Joystick up or down Navigate through the menu items. Joystick down Finish editing title. Change value. Zoom handle twist Enter editing title mode. CTRL + Joystick Change value of angle ESC Escape (EXIT) 3.4 Auto Scan (First Item of the Main menu / Shortcu
Résumé du contenu de la page N° 20
1. Press the SCAN key to enter Auto Scan menu directly. Or press the MENU key to display the main menu on the monitor. Scroll to Auto Scan and push the Joystick to the right. 2. Select an Auto Scan number by pushing the Joystick left or right. 3. Twist the Joystick to enter the title by scrolling through the alphanumeric characters and pushing the handle to the right or left to move to the next space. Press ENTR key or push the Joystick down to finish title mode. 4. When finish enter
