Résumé du contenu de la page N° 1
L73E4/US GB 1998, 20, 15
VCB-9324
INSTRUCTION MANUAL
B/W CCD Camera
About this manual
Before installing and using the camera, please read this manual
carefully. Be sure to keep it handy for later reference.
Résumé du contenu de la page N° 2
L73E4/US GB 1998, 20, 15 SANYO INDUSTRIAL VIDEO B/W VIDEO CAMERA LIMITED WARRANTY OBLIGATIONS In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user’s expense, unless specifically stated otherwise in this warranty. The names and addresses of Authorized Sanyo Service Centers may be obtained by writing to SFS Corporation, SFC’s warranty administrator, at any of the addresses listed below, or by calling (toll-free) 1-8
Résumé du contenu de la page N° 3
L73E4/US GB 1998, 20, 15 INFORMATION TO USER This equipment has been tested and found to comply with the limits Safety Guard for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against THIS SYMBOL INDICATES THAT THERE ARE harmful interference in a residential installation. This equipment IMPORTANT OPERATING AND MAINTENANCE generates, uses, and can radiate radio frequency energy and, if INSTRUCTIONS IN THE LITERATURE ACCOM
Résumé du contenu de la page N° 4
L73E4/US GB 1998, 20, 15 CONTENTS FEATURES Built-in interline transfer method 1/3" CCD, approx. 270,000 PRECAUTIONS........................................................................................ 3 picture elements PARTS NAMES AND FUNCTIONS ......................................................... 4 Low smear, anti-blooming, low lag, no burning and no geometric distortion using the CCD solid state image device CONNECTIONS AND INSTALLATION .............................................
Résumé du contenu de la page N° 5
L73E4/US GB 1998, 20, 15 PRECAUTIONS In case of problem Protect from humidity and dust Do not use the camera if smoke or a strange odour comes from the To prevent damages to the camera, do not install it where there is unit, or if it seems not to function correctly. Disconnect the power greasy smoke or steam, where the dampness may get too high, or cord immediately, and consult your dealer (or a Sanyo Authorized where there is a lot of dust. Service Centre). Protect from high temperatures Do not
Résumé du contenu de la page N° 6
GND AC AC L73E4/US GB 1998, 20, 15 PARTS NAMES AND FUNCTIONS 1 Hood lens 8 9 2 Focus ring The focus does not need adjustment for subjects 1 m and more 8 from the lens. If the subject is closer than 1 m, turn the focus ring to adjust the focus as necessary. (See page 9.) 3 Lens 4 Lens cover This cover will protect the lens from dust and damage. 5 24 V AC input terminal 5 6 7 (24 V AC, GND) With this camera use only the 24 V AC power adaptor model No. VPT-115 available from Sanyo. Power supply co
Résumé du contenu de la page N° 7
L73E4/US GB 1998, 20, 15 PARTS NAMES AND FUNCTIONS 6 Camera mounting screw hole (1/4"–20 UNC) F Line phase volume When mounting the camera to the mounting bracket, use this When using a camera switcher to connect 2 cameras or more to installation hole. one monitor, there may be a vertical roll of the images when switched. In such a case, set as described below. 7 Lens cover fixing screw Switch the display on the monitor from camera 1 to camera 2. 8 GND (ground) terminal screw Adjust the LINE PHA
Résumé du contenu de la page N° 8
L73E4/US GB 1998, 20, 15 CONNECTIONS AND INSTALLATION Connecting the coaxial cable horizontally 1 Cut and prepare the extremity of the coaxial cable (sold separately), as illustrated. 2 Attach the coaxial cable to the base. Loosen the VIDEO OUT terminal screw (A) and the GND terminal screw (B), then insert the center wire of the coaxial cable in the VIDEO OUT terminal and make sure the shielding 1 mesh part of the cable is located into the GND cable clamper, then tighten both screws (A and B) to
Résumé du contenu de la page N° 9
L73E4/US GB 1998, 20, 15 CONNECTIONS AND INSTALLATION Installing the BNC plug (sold separately) 1 2 To connect the camera to peripheral devices, use a coaxial cable with BNC plug. 1 Cut the extremity of the coaxial cable (sold separately), as illustrated. Cable type RG-6U (5C-2V), 500 m maximum. 7mm 8mm If the type of peripheral devices connected, the type of cable used and/or the cable 3 4 length are not as specified, the image and synchronization signals may not be transmitted correctly. CA
Résumé du contenu de la page N° 10
L73E4/US GB 1998, 20, 15 CONNECTIONS AND INSTALLATION Basic connections for monitoring or recording The peripheral devices (VCR, monitor, etc.) and cables are sold separately. (Example of connection to a monitor) 1 Make the video signal connection between the camera and the monitor or time lapse VCR. 2 Plug the AC adaptor to a wall outlet. Adjust the picture on the monitor using the Brightness and Contrast controls. Fig. 1 Fig. 2 : VIDEO IN : VIDEO OUT CAUTION: Make sure the AC adaptor is not
Résumé du contenu de la page N° 11
L73E4/US GB 1998, 20, 15 SETTINGS AND ADJUSTMENTS TROUBLESHOOTING Before taking the camera for repairs, please check below to make Adjusting the focus sure that the camera is used correctly. If it still does not perform 1 Loosen the lens cover fixing screw (A). correctly, please consult your dealer or a Sanyo Authorized Service 2 Turn the cover counterclockwise to align the tab (C) on the Center. lens cover with the tab (B) on the base and remove the No picture on the monitor screen cover. Is
Résumé du contenu de la page N° 12
Ω L73E4/US GB 1998, 20, 15 SPECIFICATIONS TV system EIA standard (525 TV lines, 30 Storage environmental Temperature: –20˚C ∼ +60˚C frames/sec.) conditions Humidity: less than 70% RH Scanning system 525 TV lines, 60 field/sec., Power supply 24 V AC 2:1 interlace Power consumption 2.1 W Image device Interline transfer method, 1/3 inch Weight Approx. 160 g solid state CCD Features and specifications are subject to change without prior notice Picture elements 537 (H) × 505 (V) or obligations. Effec
