Résumé du contenu de la page N° 1
00570A-SCC-C6403-ENG 8/17/06 1:51 PM Page 1
SmartDome Camera
SCC-C6403
E
Owner’s Instructions
F
Manuel d’instruction
Es
Manual del usuario
J
Part : AB68-00570A(00)
Résumé du contenu de la page N° 2
00570A-SCC-C6403-ENG 8/17/06 1:51 PM Page 3 Important Safety Instructions Safety Precautions 1. Read these instructions. The purpose of this information is to ensure proper use of this product to 2. Keep these instructions. prevent danger or damage to property. Please be sure to observe all 3. Heed all warnings. precautions. 4. Follow all instructions. * The precautions are divided into "Warnings" and "Cautions" as 5. Do not use this apparatus near water. distinguished below: 6. Clean only wit
Résumé du contenu de la page N° 3
00570A-SCC-C6403-ENG 8/17/06 1:51 PM Page 5 6. Do not place conductive objects (e.g., screwdrivers, coins, and metal FCC STATEMENT things) or containers filled with water on top of the camera. (Doing so may cause personal injury due to fire, electrical shock, or falling objects.) This device complies with Part 15 of the FCC Rules. Operation is subject to 7. Do not install the unit in humid, dusty, or sooty locations. (Doing so may cause fire or electrical shock.) the following two conditions:
Résumé du contenu de la page N° 4
00570A-SCC-C6403-ENG 8/17/06 1:51 PM Page 1-1 Table of contents Before Usage Before Usage...............................................................................................................1-1 This is a basic instruction manual for the SCC-C6403 user. It contains all the instructions needed to use the SCC-C6403 from Chapter 1 SCC-C6403 Overview..............................................................................1-4 SCC-C6403 Introduction ...............................
Résumé du contenu de la page N° 5
00570A-SCC-C6403-ENG 8/17/06 1:51 PM Page 1-3 4. ZONE SET...............................................................................................3-19 - ZONE DIR SET....................................................................................3-19 - ZONE AREA SET................................................................................3-20 Chapter 1 SCC-C6403 Overview - LOCATION .......................................................................................3-21 - ZO
Résumé du contenu de la page N° 6
00570A-SCC-C6403-ENG 8/17/06 1:51 PM Page 1-5 SCC-C6403 Introduction Locations of Control FRONT SCC-C6403 is a zoom lens built in smart dome camera which provides you with the best monitoring function in connection with CCTV at banks or companies. E The SCC-C6403 is a high quality surveillance camera using x32 zoom lens and digital zoom IC, it can catch clear images up to 320 times. SCC-C6403 has a variety of functions such as; - DAY/NIGHT to improve the sensitivity by automatic conversion in
Résumé du contenu de la page N° 7
00570A-SCC-C6403-ENG 8/17/06 1:51 PM Page 1-7 ADAPTER CONNECTION BACK SCC-C6403 Adapter BOARD E AC 24V OUT POWER AC 24V OUT POWER 1-7 1-8
Résumé du contenu de la page N° 8
00570A-SCC-C6403-ENG 8/17/06 1:51 PM Page 1-9 INITIAL SETTING Setting RS-422A/RS-485 termination CAMERA ADDRESS SETUP Use SW701, SW702, or SW703 for Camera Address setup. You may allocate up to 255 addresses by using SW701 to set the 3rd digit, SW702 the 2nd digit, and SW703 the 1st digit. 12 EX) In case of Camera Address 1, see the following figure for setup. As it is shown in the structure map, when Controller and RS-422A/RS- 485 is connected it should be terminated according to the Cable fe
Résumé du contenu de la page N° 9
00570A-SCC-C6403-ENG 8/17/06 1:51 PM Page 2-1 Before Installing Checking Package Contents Please check that all components listed below are included in the package: Chapter 2 SCC-C6403 Installation E In this chapter, we will check the contents of the package before installing the SCC-C6403, and prepare a power adapter suitable for the power supply system. (Power Consumption: 18W; Voltage: AC24V, 1.5A) Then, we will install the SCC-C6403 and connect the cables. SCC-C6403 Bracket anchor Owner’
Résumé du contenu de la page N° 10
00570A-SCC-C6403-ENG 8/17/06 1:51 PM Page 2-3 Cable Connection Preparing the Cables 1. First, connect one end of the To install and use the SCC-C6403, the following cables should be BNC video cable connector to prepared. the Video Output Terminal (VIDEO OUT) Power Adapter Cable The cable that plugs into the SCC-C6403 power input receptacle has the 2. Then, connect the other end of rated voltage of AC24V, 1.5A. the connector to the Video Input E Check the rated voltage before using the cable
Résumé du contenu de la page N° 11
00570A-SCC-C6403-ENG 8/17/06 1:51 PM Page 2-5 Installing SCC-C6403 Installation Precautions 3) INDOOR HOUSING (SHG-120) 1) Make sure that the installation site can sufficiently support a minimum of This housing is used for installing the SmartDome Camera to an indoor four times the net weight of the SCC-C6403 SmartDome Camera and wall or a ceiling. other accessories. 2) Install in an area where the space above the ceiling board is over 18 cm (7 in.) high. E 3) Use the supplied screws to fasten
Résumé du contenu de la page N° 12
00570A-SCC-C6403-ENG 8/17/06 1:51 PM Page 2-7 Installing the Camera 1. [Figure 1] Install the structure on the ceiling. (Refer to Installation reference 5) CEILING MOUNT ADAPTOR (SADT-100CM) for the Length of the structure) This adaptor is used for installing the indoor housing or the outdoor * Built in by the builder of the structure housing for the SmartDome Camera to a concrete ceiling. E [Figure 1] 2. Make a hole in the ceiling where the camera will be installed. (The hole should be about
Résumé du contenu de la page N° 13
00570A-SCC-C6403-ENG 8/17/06 1:51 PM Page 2-9 5. [Figure 5] Match the 6. Pull the safety wire from the case BRKT-ANCHOR and CAMERA body, and assembly it to the camera ADAPTER and use 4screws holder. (PH M4 x 8) to assemble them. Chapter 3 Setup Menu Overview [Figure 5] [Figure 6] In this chapter, we will look over the Setup Menu of the E SCC-C6403, First we'll look over the overall structure of the Setup Menu, and then we'll look at the functions of each menu. [Figure 7] 7. [Figure 7] Matc
Résumé du contenu de la page N° 14
00570A-SCC-C6403-ENG 8/17/06 1:51 PM Page 3-2 Structure of the Setup Menu ALARM SET ALARM PRIORITY SET ALARM1~4 1~4 EXIT QUIT/SAVE CAMERA SET CAMERA ID ON.../OFF V-SYNC INT/LINE... ALARM IN SET ALARM1~4 NO/NC/OFF COLOR/BW COLOR.../BW.../AUTO... EXIT QUIT/SAVE MOTION DET OFF/ON... ZOOM SPEED 1/2/3/4 ALARM OUT SET ALARM1~4 1~3 DIGITAL ZOOM 0FF/X2 ~ X10 MOTION 1~3 DISPLAY ZOOM OFF/ON EXIT QUIT
Résumé du contenu de la page N° 15
00570A-SCC-C6403-ENG 8/17/06 1:51 PM Page 3-4 (CAMERA SET) (CAMERA ID) ❈ If the power is turned off after PRESET, AUTO PAN, SCAN, PATTERN function is activated and no other control is made, camera CAMERA ID ON... A B C D E F G H I J K L V-SYNC INT will do the same function after the power is turned on. M N O PQ R S T U V W X COLOR/BW COLOR... ➜ Y Z 0 1 2 3 4 5 6 7 8 9 MOTION DET OFF : ! - + ✻ () / ZOOM SPEED 3 Press Use the controller to press the MENU selection key and the following DIGITA
Résumé du contenu de la page N° 16
00570A-SCC-C6403-ENG 8/17/06 1:51 PM Page 3-6 COLOR/BW ❈ In AUTO mode, AGC will be displayed as “---“. You can’t adjust the settings manually. In the COLOR/BW menu, you can switch ON or OFF the IR (infrared) Filter. In a poor illumination environment, the IR filter is turned off in the BW mode the its sensitivity increases as high as a black and white camera. On the other hand, the (CAMERA SET) (AUTO) IR filter is turned on and the sensitivity decreases in the COLOR mode. CAMERA ID OFF COLOR :
Résumé du contenu de la page N° 17
00570A-SCC-C6403-ENG 8/17/06 1:51 PM Page 3-8 Select ON and press [Enter ] to display an additional menu window of DIGITAL ZOOM “MOTION DET ”. You may set up the digital zoom magnification ratio in the DIGITAL ZOOM You can select one from the sub items of TOP..., BOTTOM..., LEFT..., menu. The magnification ratio ranges from OFF to 10. If you set Digital RIGHT..., CENTER... or USER... as AREA where the Motion Detection Zoom of SCC-C6403 to max. 10 times, the mode will become the 32 time functio
Résumé du contenu de la page N° 18
00570A-SCC-C6403-ENG 8/17/06 1:51 PM Page 3-10 EXIT For items in the BLC menu, the user can set the size and location of the BLC area by pressing [ENTER] key after put the cursor on USER… using The EXIT menu is used to quit the CAMERA SET menu of the the [Left, Right] key. For SIZE items, you can use the [Up, Down, Left, SCC-C6403 and return to the MAIN MENU. - QUIT : Ignores the changed information and restores the saved Right] key to designate the SIZE, and then press the [ENTER] key. info
Résumé du contenu de la page N° 19
00570A-SCC-C6403-ENG 8/17/06 1:51 PM Page 3-12 SHUTTER AGC You may designate both the fast electronic shutter speed and low The AGC menu was designed to provide you with brighter screen electronic shutter speed in the SHUTTER menu. The fast electronic supposed you photographed any subject in the dark resulting in less shutter supports 7 shutter speeds from 1/100(1/120) to 1/10K second to brighter image than regulated. AGC menu setup is available only when be used for the bright and fast video
Résumé du contenu de la page N° 20
00570A-SCC-C6403-ENG 8/17/06 1:51 PM Page 3-14 You can select one of four modes for white balance adjustment as follows: WHITE BAL Lights are generally denoted as color temperatures and expressed in - ATW1/ATW2(Auto-Tracing White Balance Mode): In these modes, the Kelvin (K) units. color temperature is monitored continuously and thereby white balance is The general light color temperatures are shown below. set automatically. The following are the approximate supported color temperature ran
