Instruction d'utilisation Panasonic WV-CW474S

Résumé du contenu de la page N° 1

Color CCTV Cameras
Operating Instructions
Model No. WV-CW474F
WV-CW474S
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
N1101-1121 V8QA5931BN Printed in Japan
N 19
For U.S.A
NOTE: This equipment has been tested and
found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC
CAUTION Rules. These limits are designed to provide
reasonable protection against harmful interfer-
RISK OF

Résumé du contenu de la page N° 2

FEATURES 1. The following functions are built in. (1) Auto Light Control (ALC) (2) The SUPER-D2 function eliminates interference by strong background lighting which makes the camera picture dark, such as a spotlight. Dynamic range of 46 dB (Typ) (3) Internal, Line-Locked, Multiplexed Vertical Drive (VD2) Sync (4) Auto/Manual White Balance Function (5) Electronic Shutter Function 2. Signal-to-noise ratio of 50 dB (Equivalent to AGC Off) 3. Minimum illumination of 2.4 lx (0.24 footcandle) (WIDE) (

Résumé du contenu de la page N° 3

i RIGHT button (I) (R) Moves the cursor to the right, selects the mode and adjusts some levels. o UP button (I) (U) Moves the cursor upward and selects items in the CAM SET UP menu. !0 DOWN button (I) (D) Moves the cursor downward and selects items in the CAM SET UP menu. !1 SET button (I) (S) Activates an item selected in the CAM SET UP menu. !2 BW AUTO1 LEVEL switch (SW5) Selects the illuminance level in LOW or HIGH mode for B/W. The factory default setting is HIGH. !3 BW switch (SW4) Switches

Résumé du contenu de la page N° 4

SETUP 1. CAMERA SETUP MENU This camera utilizes an on-screen user setup menu. • Opening the Setup Menu ** CAM SET UP ** Press and hold down I(S) for 2 seconds CAMERA ID OFF ALC ALC or more. SHUTTER --- AGC ON(DNR-H) SENS UP OFF The CAM SET UP menu appears on the SYNC INT monitor as shown at right. WHITE BAL ATW1 MOTION DET OFF Check the current settings on the menu. DIP SW END SET UP DISABLE Refer to the following sections for a de

Résumé du contenu de la page N° 5

SETTING PROCEDURES 1. Camera Identification (CAMERA ID) Setting You can use the camera identification (CAMERA ID) to assign a name to the camera. The camera ID consists of up to 16 alphanumeric characters. The camera ID display can be switched on or off on the monitor screen. To edit the CAMERA ID 1. Move the cursor to CAMERA ID. The factory default setting is OFF. 2. Press I(S). The CAMERA ID menu Character Cursor appears. The cursor on the letter “0” is 0123456789 highlighted. ABCDEFG

Résumé du contenu de la page N° 6

Résumé du contenu de la page N° 7

6. Synchronization Setting (SYNC) You can select internal sync (INT) mode, line-lock (LL) mode or the VD2 signal (multiplexed vertical drive signal) mode. Important Notices: 1. The priority for the sync modes is as follows: (1) Multiplexed Vertical Drive (VD2) (Highest priority) (2) Line-lock (LL) (3) Internal Sync (INT) (Lowest priority) 2. The line-lock mode has a submenu for line-lock vertical phase adjustment. If the cam- era installation is relocated, check the vertical phase adjustment aga

Résumé du contenu de la page N° 8

Résumé du contenu de la page N° 9

9-6 Electronic Zoom (EL-ZOOM) 1. Move the cursor to EL-ZOOM. 2. Select ON or OFF using I(L) or I(R). The factory default setting is OFF. ON: x2 electronic zoom is available with the ZOOM switch on the controller. OFF: The electronic zoom function is disabled. 3. While the cursor is on EL-ZOOM, press I(S). The EL-ZOOM setting menu ** EL-ZOOM ** appears. PAN/TILT →PUSH SET ZOOM →PUSH SET 4. Move the cursor to PUSH SET for ZOOM and press I(S) to display the ZOOM

Résumé du contenu de la page N° 10

SPECIFICATIONS Pick-up Device: 768 (H) x 494 (V) pixels, Interline Transfer CCD Scanning Area: 4.8 (H) x 3.6 (V) mm (Equivalent to scanning area of 1/3” pick-up tube) Scanning: 525 lines/60 fields/30 frames Horizontal: 15.734 kHz Vertical: 59.94 Hz Synchronization: Internal, Line-locked or Multiplexed vertical drive (VD2) Sync selectable Video Output: 1.0 V[p-p] NTSC composite 75 Ω /BNC connector Horizontal Resolution: 480 lines (C/L), 570 lines (B/W) Signal-to-Noise Ratio: 50 dB (Equivalent to