Résumé du contenu de la page N° 1
TK-C625.book Page 1 Thursday, March 31, 2005 4:20 PM
DOME TYPE CAMERA
INSTRUCTIONS
TK-C625
For Customer Use:
Enter below the Model No. and Serial
No. which is located on the body. Retain
this information for future reference.
Model No. TK-C625
Serial No.
LWT0254-001A-H
Résumé du contenu de la page N° 2
TK-C625.book Page 2 Thursday, March 31, 2005 4:20 PM Safety Precautions 2 EN FOR USA AND CANADA INFORMATION FOR USA 8 INFORMATION This equipment has been tested and found to comply with CAUTION the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. RISK OF ELECTRIC SHOCK These limits are designed to provide reasonable protection DO NOT OPEN against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency CAUTIO
Résumé du contenu de la page N° 3
TK-C625.book Page 3 Thursday, March 31, 2005 4:20 PM IMPORTANT SAFEGUARDS EN 3 These are general IMPORTANT SAFEGUARDS and certain items may not apply to all appliances. IMPORTANT SAFEGUARDS 1. Read all of these instructions. 2. Save these instructions for later use. 3. All warnings on the product and in the operating instructions should be adhered to. 4. Unplug this appliance system from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for clea
Résumé du contenu de la page N° 4
TK-C625.book Page 4 Thursday, March 31, 2005 4:20 PM Introduction 4 EN Thank you for purchsing this product. Contents (These instructions are for TK-C625U/TK-C625E) TK-C625U : For North American Market. Safety Precautions 2 TK-C625E : For European Market. “TK-C625” is used for common descriptions between both IMPORTANT SAFEGUARDS 3 models in this manual. Before beginning to operate this unit, please read the Introduction 4 instruction manual carefully in order to make sure that the best Chara
Résumé du contenu de la page N° 5
TK-C625.book Page 5 Thursday, March 31, 2005 4:20 PM Introduction (continued) EN 5 Operating Precautions ●To save energy, turn the system off whenever it is not in use. 8 WARNING ●This camera has been designed for indoor use. It cannot be ●Install the unit on a strong and stable surface. used outdoors. This unit has been designed to revolve at high speed. Due ●This camera has been designed to be hung from a ceiling. to its weight (about 1.3 kg) and the vibrations it may be Do not install it i
Résumé du contenu de la page N° 6
TK-C625.book Page 6 Thursday, March 31, 2005 4:20 PM Introduction (continued) 6 EN Operating Precautions (continued) ●If a very bright object (such as a lamp) is being monitored, 8 Zooming operation the picture may contain vertical lines (smear) above and The following phenomena are due to the characteristics below the bright object in the picture. This is a phenomenon of the built-in lens and are not malfunctions. normal to a solid-state image pickup device (CCD) and is not ●Focus may deviat
Résumé du contenu de la page N° 7
TK-C625.book Page 7 Thursday, March 31, 2005 4:20 PM Introduction (continued) EN 7 Name and Function of Parts 8 Ceiling Mount (Terminal Side) I H G A F B E D C A Safety Wire F Locking Screw Hang this wire to the Fastening Hook for Safety Wire S. For fastening the camera body. Ensure to fasten the Camera Clamping Bracket P using this screw. B [VIDEO OUT] Coaxial Cable Terminal Output terminal of a composite video signal (1 V(p-p)) with G [CONTROL] Control Signal Terminal (J501) an output imped
Résumé du contenu de la page N° 8
TK-C625.book Page 8 Thursday, March 31, 2005 4:20 PM Introduction (continued) 8 EN Name and Function of Parts (continued) 8 Ceiling Mount (Setting Switch Side) 8 Camera N S O J M P L J K R Q J Clamping Hole (x 4) O Camera Connection Terminal (Male) Use these holes to attach the camera to the ceiling or For connection to the Camera Connection Terminal ceiling recessed bracket (WB-S625: sold separately). (Female) K on the ceiling mount. K Camera Connection Terminal (Female) P Camera Clamping Br
Résumé du contenu de la page N° 9
TK-C625.book Page 9 Thursday, March 31, 2005 4:20 PM Connections & Installation EN 9 Multi-Drop Communication System A system that employs the RM-P2580 as the controller. The following figure shows a system that can accommodate up to eight cameras. (100 positions can be preset per camera.) Observe the following points when connecting Camera 1 Control signal cable components together: ●Turn all the components off before proceeding. Coaxial cable TK-C625 ●Read the instruction manuals of all co
Résumé du contenu de la page N° 10
TK-C625.book Page 10 Thursday, March 31, 2005 4:20 PM Connections & Installation (continued) 10 EN Multi-Drop Communication System (continued) A system that does not employ the RM-P2580 as the controller. MEMO ● Be sure to terminate the control signal cable at both ends. The cables (length of stub) connecting pieces of non-terminated equipment (cameras or controllers) must be as short as possible. If the length of stub is too long, control precision may suffer. CONTROL Cable CAM1 CAM2 Leng
Résumé du contenu de la page N° 11
TK-C625.book Page 11 Thursday, March 31, 2005 4:20 PM Connections & Installation (continued) EN 11 Point-to-Point Communication System The following illustration shows a system in which a remote control unit (or a similar piece of equipment) controls a single camera. Video out Control signal cable AC 24 V power supply (A CAUTIONS) Monitor Switch 4 : OFF (Point to Point) Switch 8 : ON Controller (Terminated 110 K) Observe the following points when connecting components together: ●Turn all th
Résumé du contenu de la page N° 12
TK-C625.book Page 12 Thursday, March 31, 2005 4:20 PM Connections & Installation (continued) 12 EN Point-to-Point Communication System (continued) Use twisted-pair cables for the connections. ●Duplex ●Simplex When the camera is controlled using the full duplex protocol, When the camera is controlled using the simplex set the Switch 5 of the Setting switch to ON. transmission protocol, set the Switch 5 of the Setting switch Camera Controller to ON. RX+ TX+ Camera Controller RX+ TX+ RX- TX- R
Résumé du contenu de la page N° 13
TK-C625.book Page 13 Thursday, March 31, 2005 4:20 PM Connections & Installation (continued) EN 13 Switch Settings Set the switches on the Ceiling Mount before installing the camera. Settings vary according to configuration of the system used. 8 Setting switches AMachine ID Setting SwitchB (A pg. 14) Switch 1 : Invalid (Set to OFF) Switch 2 : Invalid (Set to OFF) Switch 3 : Invalid (Set to OFF) Switch 4 : PROTOCOL(1) Switch 5 : PROTOCOL(2) Switch 6 : SYNC Switch 7 : Invalid (Set to OFF) Swit
Résumé du contenu de la page N° 14
TK-C625.book Page 14 Thursday, March 31, 2005 4:20 PM Connections & Installation (continued) 14 EN Switch Settings (continued) 8 Machine ID Setting Switch When controlling the system using a multi-drop remote 1 Output video image for checking to the monitor control unit such as RM-P2580, for instance, assign a number (machine ID) for identification to each of the 2 Turn on the power (AC 24 V) of the camera connected cameras. 3 Camera initializes Assign a m
Résumé du contenu de la page N° 15
TK-C625.book Page 15 Thursday, March 31, 2005 4:20 PM Connections & Installation (continued) EN 15 8 Machine ID Set the Machine ID using a combination of numbers between 1 to 8. (This is set to OFF in the factory settings.) Machine ID Installation Machine ID Installation Machine ID Installation Machine ID Installation Machine Machine Machine Machine Switch Switch Switch Switch ID ID ID ID 1 27 53 79 2 28 54 80 3 29 55 81 4 30 56 82 5 31 57
Résumé du contenu de la page N° 16
TK-C625.book Page 16 Thursday, March 31, 2005 4:20 PM Connections & Installation (continued) 16 EN Cable Connections CAUTIONS ●Ensure to attach the cover for the ceiling mount. Installation is not possible without attaching the cover. ●The cover prevents penetration of foreign objects into the ceiling mount. Penetration of foreign objects may cause a malfunction or, in the worst scenario, cause smoking or fire. Connection Procedure 1 Make a hole in the ceiling 4 Connect the cable to this came
Résumé du contenu de la page N° 17
TK-C625.book Page 17 Thursday, March 31, 2005 4:20 PM Connections & Installation (continued) EN 17 Connection of Alarm Input / Output Terminals Connection of Coaxial Cables Connect the alarm input/output terminals to external Connecting an RG-59 coaxial cable. devices such as sensors and buzzers. Strip the tip of the coaxial cable according to the diagram below. A Follow the diagram below to loosen and remove the screws on the two edges of the terminal block. * B Strip the coating of the alar
Résumé du contenu de la page N° 18
TK-C625.book Page 18 Thursday, March 31, 2005 4:20 PM Connections & Installation (continued) 18 EN Cable Connections (continued) Connection of Control Signal Cables Connection of Power Connect this to the remote control unit (RM-P2580). Connect to an AC 24 V Supply. The maximum permissible length of the control signal cable during connection with RM-P2580 is 1200m. (RM-P2580 allows connection of a set of cables to multiple cameras. In this case, the total length of the cables shall not exceed
Résumé du contenu de la page N° 19
TK-C625.book Page 19 Thursday, March 31, 2005 4:20 PM Connections & Installation (continued) EN 19 Installing the Ceiling Mount 2 Fasten the ceiling mount to the ceiling CAUTIONS Align the ADFRONT markB to the front direction that the ●Attachment of a recessed cover in the ceiling (recess bracket) camera is facing, and fasten the ceiling mount to the ceiling may be mandatory in certain regions. If this is so, ensure that using the 4 screws while paying attention not to catch the the recessed
Résumé du contenu de la page N° 20
TK-C625.book Page 20 Thursday, March 31, 2005 4:20 PM Connections & Installation (continued) 20 EN Installing the Camera 1 Attach the Safety Wire 4 Turn the camera Follow the diagram to pull out the Safety Wire from the Make sure that the camera is not tilted, followed by pushing ceiling mount, followed by hanging it to the Fastening Hook the camera against the ceiling mount and turning it in the for Safety Wire on the camera. clockwise direction until it stops.Upon doing so, check that the C
