Résumé du contenu de la page N° 1
®
METROLOGIC INSTRUMENTS, INC.
®
TECH 7 Laser Bar Code
Projection Scanner
Installation and User’s Guide
Résumé du contenu de la page N° 2
Copyright © 2006 by Metrologic Instruments, Inc. All rights reserved. No part of this work may be reproduced, transmitted, or stored in any form or by any means without prior written consent, except by reviewer, who may quote brief pas- sages in a review, or provided for in the Copyright Act of 1976. Products and brand names mentioned in this document are trademarks of their respective companies.
Résumé du contenu de la page N° 3
Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Unpacking List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Scanner Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Configuration to the Host System . . . . . . . . . . . . . . . . . . . . . . . . .3 Stand Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Back Plate Inst
Résumé du contenu de la page N° 4
Résumé du contenu de la page N° 5
Introduction ® Metrologic's TECH 7 laser bar code projection scanner is encased in an NEMA-12 steel case. The case construction enables the scanner to operate in harsh surroundings, especially industrial environments. Water-resistant, shock-resistant, and rugged, the TECH 7 is also fast, aggressive and reliable. It can register bar codes at a range of 76mm - 254mm (3" - 10") and can autodiscriminate among all common codes. To suit particular applications, two different scan patterns are avai
Résumé du contenu de la page N° 6
Scanner Installation To maintain compliance with applicable standards, all circuits con- nected to the scanner must meet the requirements for SELV (Safety Extra Low Voltage) according to EN 60950. To avoid potential prob- lems, do not power up the scanner until the communication cable is secured to the host. 1. "Power off" the host system. 2. Locate the 19-pin female end of the scanner link cable and find the widest key located above pins L and A. Align this key with the corresponding key on
Résumé du contenu de la page N° 7
Configuration to the Host System The scanner is shipped from the factory programmed to a set of default conditions noted in the ScanSelect™ Scanner Programming Guide by an asterisk that appears before the brief definition located next to the bar code. In order for the scanner to communicate with a host system properly, it may need to be programmed. Since each host system is unique, con- figure the scanner to match the host system requirements. Configure the scanner by entering the program mode
Résumé du contenu de la page N° 8
Stand Installation With the Metrologic stand (Part #45475), the scanner can be posi- tioned in one of two directions. The two orientation choices are vertical or horizontal. (Refer to Figure 1) Vertical Mount Horizontal Mount Figure 1: Stand Orientation To install this stand, use the four 6-32 x ½ inch machine screws and two #10 pan head wood screws. 1. Drill two holes into the work surface that are the same size and distance as the holes on 1.00 in the stand base. (Refer to Figure 2) 3.00
Résumé du contenu de la page N° 9
Back Plate Installation With the Metrologic back plate (Part #45473), position the scanner in one of two directions. The two Vertical Mount orientation choices are vertical or horizontal. (Refer to Figure 4). To use this stand, use the four 6-32 x ½ inch machine screws and Horizontal Mount four wood screws to attach the unit to the back plate and work surface. The maximum distance the screws Figure 4: Back Plate Orientation should go into the scanner is a ½ inch. 1. Drill four holes i
Résumé du contenu de la page N° 10
Parts of Scanner 1 2 3 4 Figure 6: Scanner Parts 1 Greenand RedLEDs When the green LED is on, this indicates that the unit is receiving power and the laser is on. When the red LED flashes on, the scanner has read a bar code successfully. When the red light turns off, communication to the host is complete. 2 Speaker The speaker emits a beep when a bar code has been decoded. 3 Laser Output Window This aperture emits the laser light. 4 Mil specConnector The 19-pin male Mil spec connector was
Résumé du contenu de la page N° 11
Visual Indicators There is a red and green LED at the top of the scanner. When the scanner is on, the flashing or stationary activity of the LEDs indicates the status of the scan and scanner. Steady Green When the laser is on, the green LED is also on. This occurs when an object is in the scan field. Steady Green; Red Flash When the scanner successfully reads a bar code, the red LED will flash then beep once. If the red LED does not flash or the scanner does not beep once, then the bar code has
Résumé du contenu de la page N° 12
Signaux Optiques Sur la partie supérieure du scanner se trouvent une diode LED rouge et une diode LED verte. Quand le scanner est sous tension, les diodes rouge et verte clignotantes ou allumées vous informent sur l'état du scanner. Ni la diode rouge, ni la diode verte n'est allumée Il existe deux raisons possibles pour que les diodes ne s'allument pas. Premièrement: si le scanner reçoit de l'énergie sans que les diodes ne s'allument, le scanner est resté sans servir pendant une certaine périod
Résumé du contenu de la page N° 13
Optische Anzeigen Auf dem Scanner befinden sich eine rote und eine grüne Leuchtdiode. Bei eingeschaltetem Scanner geben Ihnen die blinkenden bzw. feststehenden Leuchtdiodenanzeigen Aufschluß über den Abtast-und Scannerstatus. Weder rote noch grüne Leuchtdiodenanzeige Es gibt zwei mögliche Gründe, weshalb die Leuchtdiodenanzeigen nicht aufleuchten. Erstens: Wenn der Scanner mit Energie versorgt wird und die Leuchtdiodenanzeigen nicht aufleuchten, so ist der Scanner für einen bes- timmten Zeitraum
Résumé du contenu de la page N° 14
Segnali Ottici Sullo scanner si trovano due diodi luminosi: uno rosso e uno verde. Quando lo scanner è inserito, i diodi luminosi, che possono o essere accesi in continuazione o lampeggiare, Vi informano sullo stato della scansione e dell'apparecchio. Né il diodo luminoso rosso né quello verde sono accesi Vi sono due possibili cause se i diodi luminosi non sono accesi. Prima causa: se lo scanner viene alimentato e i diodi luminosi non sono accesi, lo scanner è rimasto disattivato per un determin
Résumé du contenu de la page N° 15
Labels There is one label located inside the window of the scanner noting that this device is a CDRH Class IIa laser product and IEC 825 LASERKLASSE 1. Also, on the scanner is a label located on the back of the unit. This label contains information such as the model number, date of manufacture, serial number, and approvals. The following are samples of the labels located on the unit. ® Metrologic This product complies with US Metrologic Instruments, Inc. DHHS Standard 21 CFR Chapter 1 Blackwo
Résumé du contenu de la page N° 16
Depth of Scan Field for the MS770 Scanner The depth of field for the scanner is 76mm to 254mm (3.00” - 10.00”) from the laser output window. Pass the symbol through the scan area in order for the scanner to recognize the bar code. (Refer to Figure 7) 76 mm [3.00 in] 254 mm [10.00 in] 152 mm [6.00 in] Figure 7: MS770 Scanner, Front View 12
Résumé du contenu de la page N° 17
Depth of Scan Field for the MS775 Scanner The depth of field for the scanner is 76mm to 254mm (3.00” - 10.00”) from the laser output window. Pass the symbol through the scan area in order for the scanner to recognize the bar code. (Refer to Figure 8) 76 mm [3.00 in] 254 mm [10.00 in] 229 mm [9.00 in] Figure 8: MS775 Scanner, Front View 13
Résumé du contenu de la page N° 18
Maintenance Smudges and dirt can interfere with the proper scanning of a bar code. Therefore, the output window will need occasional cleaning. 1. Spray glass cleaner onto lint free, nonabrasive cleaning cloth. 2. Gently wipe the output window. Applications and Protocols The model number on each scanner includes the scanner number and communications protocol. Version Identifier Communication Protocol(s) 1 RS-232, OCIA, Bidirectional RS-232 15 Light Pen Emulation 14
Résumé du contenu de la page N° 19
Appendix A Specifications Application: Industrial Projection Scanner Light Source: Visible Laser Diode 650 ± 5 nm or 670 ± 5 nm CDRH: CLASS IIa laser product Certifications: CE, UL listed for the US and CUL for Canada EMC: EN 60825: Class 1 EMI: FCC, ICES-003 & EN 55022 Class A Mechanical Dimensions: 184 mm(L) x 186 mm (W) x 78 mm (D) [7.25 in (L) x 7.3 in (W) x 3.06 in (D)] Weight: 2.35 kg. (5.19 lbs.) without cable Orientation: May be used in any orientation Mounting: Back plate mount or Ve
Résumé du contenu de la page N° 20
Appendix A (Continued) Operational Depth of Scan Field: 76mm to 254 mm (3 in to 10 in) Scan Speed: Model 770: 2000 scan lines per second Model 775: 1200 scan lines per second Scan Pattern: Model 770: Omnidirectional (20 interlocking lines) Model 775: 12-line raster Indicators: LED: green = laser on; red = good read Beeper Operation: Selection of 3 tones for "Good Read" Maintenance Required: Clean window periodically Decode Capability: Autodiscriminates System Interfaces: RS232C; Light Pen E
