Résumé du contenu de la page N° 1
User Manual
Flextight X5 / X1
English – v/1.3
Résumé du contenu de la page N° 2
Table of contents Warnings and Restrictions 4 System Requirements 4 Par ts and components 5 Fr o n t p a n e l 5 B a c k p a n e l a n d c u t a w ay v i e w 6 Set ting up t he Scanner 7 E nv i r o n m e n t a l R e q u i r e m e n t s E l e c t r i c a l R e q u i r e m e n t s I n s t a l l a t i o n P r o c e d u r e, F i r eW i r e I n t e r f a c e Operating Instructions 9 Resolutions 10 Tr u e R e s o l u t i o n s Calibrating the Scan
Résumé du contenu de la page N° 3
The Flextight X1 and the Flextight X5 satisfy the demand Removal and both utilize Hasselblad’s unique FlexColor for image quality and speed requirements from profes- software and 3F – Flexible File Format. These features pro- sional photographers and production environments alike. duce a digital data management system to provide users with a fully integrated workflow solution that spans from Developed around Hasselblad’s patented virtual drum image capture to output. Both scanners are PC and
Résumé du contenu de la page N° 4
Warnings and restrictions • Read all of the included documentation before attempting to install and use the scanner. • Do not touch the originals and/or the original holder while scanning. • Do not start scanning or previewing until an original holder with an original has been mounted. • The original holder is only to be mounted or removed when the drum is in the load position. • When you turn on the scanner, the drum w
Résumé du contenu de la page N° 5
Parts and components − front panel A D E F B G H C I F Power indicator (Green) A Feed table Remains lit when ready to scan. Flashes when first installed This must be in the lower position for normal scanning. to indicate that firmware must be loaded (it will be loaded When scanner is not in use you can return it to closed automatically when you run FlexColor). position to protect it from dust etc. Adjust to horizontal position
Résumé du contenu de la page N° 6
FLEXTIGHT ORIGINAL HOLDER PATENT PENDING Parts and components − cutaway view A B A B C D E F G H F Upper light source A Power cable socket Illuminates reflective originals. Flextigh X5 only. Connect the power cable into this socket. G Prism-module B FireWire interface sockets Focuses the light from various angles and thereby removes Socket for FireWire cable (max. 6 m) for computer con- or heavily reduces dust and scratches in the scanned image.
Résumé du contenu de la page N° 7
Setting up the scanner Environmental requirements Set up the scanner in a location that fulfils the following requirements: • Keep the scanner away from sources of heat, such as direct sunlight or a radiator. Warm temperatures will degrade the quality of your scans - for best results, work in a cool environment. • The scanner must be operated away from sources of strong electromagnetic inter- ference. Although the scanner
Résumé du contenu de la page N° 8
FLEXTIGHT ORIGINAL HOLDER PATENT PENDING For horizontal positioning lift the table free from the hinges and push. Closed Horizontal Normal D A E F G H I J L K B C 8
Résumé du contenu de la page N° 9
FLEXTIGHT ORIGINAL HOLDER PATENT PENDING Operating instructions 1. It is assumed that the scanner and FlexColor software have been properly installed. 2. If not already done, lower the feed table A to normal position. 3. Press the red power button F on the front of the scanner to switch it on. The green light G starts flashing. This means that no firmware has been downloaded yet. It will be downloaded automatically later when you first run the FlexColor program. 4. Turn on your comp
Résumé du contenu de la page N° 10
lines printed on the holder to line up the image. Handle the clear plastic layer only by the edges to avoid fingerprints. Curl the plastic layer back and slip the front edge into Flextight’s foil holder. 9. Lay the top layer of the holder down flat over the original. • For the reflective holder, note the four metal pegs (the top two are shown as A and C in the figure below); make sure that the clear plastic sheet is pressed all the way down over all four pegs. Note also the two curved ta
Résumé du contenu de la page N° 11
Calibrating the scanner The Flextight X5 scanner requires two types of calibration The Flextight X1 only requires one: • Both scanners require focus calibration. Focus calibration adjusts the positioning of the scanners’ optics for each zoom level. If your scans appear unfocused or are slightly the wrong size, then you may need to make a new focus calibration to adjust the zoom mechanism. The focus calibration is stored in t
Résumé du contenu de la page N° 12
Focus calibration The Flextight scanner uses an adjustable zoom and focus mechanism to optimize its scanning resolution for each of the original formats it can handle. If you suspect your scans are not as sharp as they should be, then you may need to calibrate your scanner. Note that you must not calibrate the scanner every day. It is intended that the scanner is calibrated not more than once every three months. In most
Résumé du contenu de la page N° 13
White calibration for reflectives The Flextight X5 scanner uses a white reference to make sure that all elements in the scanner’s CCD react consistently to light brightnesses. The scanner has been calibrat- ed at the factory, and the calibration data is stored in the scanner’s flash PROM. As the scanner ages, the properties of the light tubes may change slightly. Therefore, you must redo the white calibration every six months
Résumé du contenu de la page N° 14
The light tubes The Flextight X5 contains two light tubes: one for illuminating reflective originals from above, the other for shining light through transparencies from below. The Flextight X1 has only one light tube for transparency scanning. NOTE! The two lamps are of different types and are not interchangeable. Replacing the light tubes If scans are suddenly coming out black (or all white if you are scanning negatives), the
Résumé du contenu de la page N° 15
B D C A A E PULL OUT PRESS G H PRESS F PULL OUT 15
Résumé du contenu de la page N° 16
Cleaning the external surface of the scanner The external surface of the scanner can be cleaned with a damp cloth. Be careful not to allow any moisture inside the scanner or on any of the connectors. Do not use alcohol or other solvents. Disposal If you need to dispose of the scanner, it must be delivered to an authorized waste plant for electronics equipment. Technical specifications Power Connector Power Consumption
Résumé du contenu de la page N° 17
FCC Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruct
Résumé du contenu de la page N° 18
CE – Declaration of conformity 18
Résumé du contenu de la page N° 19
CE – Declaration of conformity 19
Résumé du contenu de la page N° 20
© 2006 Hasselblad A/S. All rights reserved. Flextight X1 / X5 User’s Guide, Part No 75020123, revision 1.3 The information in this manual is furnished for informational use only, is subject to change without notice, and should not be construed as a commitment by Hasselblad A/S. Hasselblad A/S assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual. Hasselblad A/S assumes no responsibi
