Résumé du contenu de la page N° 1
4’’ DRY TILE SAW
Model 38941
ASSEMBLY AND OPERATION INSTRUCTIONS
Diamond Blade not included; sold separately.
Due to continuing improvements, actual product may differ slightly from the product described herein.
Distributed Exclusively by Harbor Freight Tools
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
TO PREVENT SERIOUS INJURY, READ AND UNDERSTAND
ALL WARNINGS AND INSTRUCTIONS BEFORE USE.
© ®
Copyright 1998, 2006 by Harbor Freight Tools .
Résumé du contenu de la page N° 2
SPECIFICATIONS Motor 110 V~, 3.2 A (No Load) RPM 10,525 #230373 Cutting Capacity 1-3/8” Blade (sold separately) 4” Diameter x 5/8” Arbor Overall Dimensions 9” x 7” x 7-3/4” Overall Weight 7.6 lb. Motor is double insulated The Tile Saw comes with an Arbor wrench and a T-Handle Wrench. A Blade is not included with the Tile Saw and must be purchased separately. Recommended saw blade is item #34441 - 4” Diamond blade-Dry type. Saw blades are available at Harbor Freight Tools. Save This Manual
Résumé du contenu de la page N° 3
2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes. 3. Keep bystanders, children, and visitors away while operating a power tool. Distrac- tions can cause you to lose control. Protect others in the work area from debris such as chips and sparks. Provide barriers or shields as needed. ELECTRICAL SAFETY 1. Double insulated tools are equipped with a polarized plug (o
Résumé du contenu de la page N° 4
5. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the power tool in unexpected situations. 6. Use safety equipment. Always wear eye protection. Dust mask, nonskid safety shoes, hard hat, or hearing protection must be used for appropriate conditions. Always wear ANSI-approved safety goggles and a dust mask/respirator when using or performing maintenance on this tool. TOOL USE AND CARE 1. Use clamps (not included) or ot
Résumé du contenu de la page N° 5
SPECIFIC SAFETY RULES 1. Maintain labels and nameplates on the tool. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. 2. Maintain a safe working environment. Make sure there is adequate surrounding work- space. Do not use this product in a damp or wet location. 3. Avoid unintentional starting. Make sure you are prepared to begin work before turning on the tool. 4. Always keep the extension cord away from moving parts on the tool.
Résumé du contenu de la page N° 6
GROUNDING Outlets for 2-Prong Plug DOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS 1. Tools marked “Double Insulated” do not require grounding. They have a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and the National Electrical Code. (See Outlets for 2-Prong Plug.) 2. Double insulated tools may be used in either of the 120 volt outlets shown in the prec
Résumé du contenu de la page N° 7
8. Protect your extension cords from sharp objects, excessive heat, and damp or wet ar- eas. RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS* (120 OR 240 VOLT) NAMEPLATE EXTENSION CORD LENGTH AMPERES (at full load) 25 Feet 50 Feet 75 Feet 100 Feet 150 Feet 0 – 2.0 18 18 18 18 16 2.1 – 3.4 18 18 18 16 14 3.5 – 5.0 18 18 16 14 12 5.1 – 7.0 18 16 14 12 12 7.1 – 12.0 18 14 12 10 - 12.1 – 16.0 14 12 10 - - 16.1 – 20.0 12 10 - - - * Based on limiting the line voltage drop to five volts at 150% of t
Résumé du contenu de la page N° 8
OPERATION Installing and Removing the Cutting Blade 1. Your Tile Saw comes with an arbor wrench and a T-Handle socket wrench for use when installing or removing a Blade. When installing or removing a blade, always make sure the tool is OFF and unplugged. 2. A Diamond Cutting Blade is not included with the Tile Saw and must be purchased separately. 3. Turn the Tile Saw so that you are looking at the Blade wheel. Place the arbor wrench (58) on the Outside Flange (2) to hold the flange in pla
Résumé du contenu de la page N° 9
PARTS LIST Part Description Quantity Part Description Quantity 1 Hex Bolt 1 31 Air Guide 1 2 Outside Flange 1 32 Screw 4 x 16 1 3 Inside Flange 1 33 Cord Cup 1 4 Screw M4 x 8 3 34 Switch Sleeve 1 5 Elastic Washer 4 3 35 Switch 1 6 Bearing Cover 1 36 Enclosure 1 7 O Sealing Ring 1 37 Screw 4 x 20 4 8 Spindle 1 38 Nameplate 1 9 Woodruff Key 3 x 13 1 39 Washer 5 3 10 Bearing 1 40 Spring washer 5 3 11 Elastic Distance Ring 1 41 Screw M5 x 40 3 12 Screw M4 x 25 4 42 Brush holder 2 13 Elastic Washer
Résumé du contenu de la page N° 10
Record Product’s Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available indi- vidually as replacement parts. SKU 38941 For technical questions, please call 1-800-444-3353. Page 10
Résumé du contenu de la page N° 11
WET CUT ATTACHMENT (38942) (Please order separately- not included with the 4” Dry Tile Saw) The Wet Cut Attachment includes a 1/4” I.D. x 9.5 foot vinyl hose, water plug with screw and rubber connector Assembly Instructions Note: In step one (1) do not completely remove the Thumb Bolt. 1. Loosen the Thumb Bolt (55), lower the guide, and re-tighten the Thumb Bolt. 2. Attach the Water Plug to the Water Tube (52) using the screw. 3. Connect the HOSE to the Water Plug. 4. Attach the Rubber Connec
Résumé du contenu de la page N° 12
Warning: When using the Wet Cutting Attachment, extreme care must be taken to insure that the saw’s electrical cord is positioned to remain dry and free from the water hose at all times. The operator must be aware that an extreme electri- cal hazard can occur if the cord, or the operator becomes wet while using this electric powered tool. Care and common sense must be used in planning a safe work area and in finding a safe location for the water bucket described below. Gravity Feed Instr
Résumé du contenu de la page N° 13
90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from de- fects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installa- tion, no
