Résumé du contenu de la page N° 1
MODEL T10460, T10462 &
T10464
PANEL SHAPING JIG
OWNER'S MANUAL
(For models manufactured since 01/12)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
Résumé du contenu de la page N° 2
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death. The owner of this machine/tool is solely responsible for its safe use. This responsibility includes but is not limited to
Résumé du contenu de la page N° 3
Table of Contents INTRODUCTION ............................................... 2 SECTION 4: ACCESSORIES ......................... 17 SECTION 5: MAINTENANCE ......................... 18 SECTION 6: SERVICE ................................... 18 SECTION 1: SAFETY ....................................... 5 SECTION 7: PARTS ....................................... 19 SECTION 2: SETUP ......................................... 8
Résumé du contenu de la page N° 4
INTRODUCTION Manual Accuracy Contact Info your jig may not exactly match the manual Machine Description www.grizzly.com
Résumé du contenu de la page N° 5
Identification Figure 1. To reduce the risk of serious injury when using this machine, read and understand this entire manual before beginning any operations.
Résumé du contenu de la page N° 6
Machine Data Sheet Machine Data Sheet MODEL T10460, T10462, T10464 PANEL SHAPING JIG Model Number T10460 T10462 T10464 Product Dimensions Shipping Dimensions Pneumatic Construction
Résumé du contenu de la page N° 7
SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of impor- tance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. Indica
Résumé du contenu de la page N° 8
DISCONNECTING POWER SUPPLY. GUARDS & COVERS. NEVER STAND ON MACHINE. APPROVED OPERATION. STABLE MACHINE. DANGEROUS ENVIRONMENTS. AWKWARD POSITIONS. ONLY USE AS INTENDED. UNATTENDED OPERATION. OFF USE RECOMMENDED ACCESSORIES. MAINTAIN WITH CARE.
Résumé du contenu de la page N° 9
Additional Safety Instructions for Jig OPERATING MACHINERY. FEEDING WORKPIECE. STARTING MACHINE. SHOP SAFETY. DEPTH OF CUT. KICKBACK. SHAPING CONTOURED WORK. HAND POSITIONING. BLIND CUT WHEN POSSIBLE. SAFETY GUARDS.
Résumé du contenu de la page N° 10
SECTION 2: SETUP Unpacking This jig presents seri- ous injury hazards to untrained users. Read through this entire man- ual to become familiar please call us immediately at with the controls and (570)546-9663. operations before using the jig! Otherwise, filing a freight claim can be difficult. Wear safety glasses dur- ing the entire setup pro- cess! SUFFOCATION HAZARD! Keep children and pets away This jig and
Résumé du contenu de la page N° 11
Box 1: (Figures 2) Qty Site Considerations A. B. C. " D. " Shaper Table Size E. F. G. H. I. J. Placement Location K. L. M. N. O. Figure 3 Figure 3. Figure 2. Children and visitors may be seriously injured if unsu- If you cannot find an item on this list, pervised around machinery. carefully check the jig and the
Résumé du contenu de la page N° 12
Attaching Guards Test Run Figure 4 Troubleshooting Page 20 To verify the jig runs correctly: 1. Figure 4. 2. 3. ON Air Connection 4. Figure 5 5. 6. In-Line Quick-Disconnect Air Piping Oiler Fittings Filter Male Female Regulator (Optional) Your Tool Filter Water Lead-In Automatic Separator
Résumé du contenu de la page N° 13
SECTION 3: OPERATIONS To complete a typical operation, the Operation Overview operator does the following: 1. 2. 3. not 4. 5. OFF 6. 7. To reduce the risk of 8. serious injury when using this jig, read and understand this entire manual before operating. 9. 10. OFF Damage to your eyes and lungs could result from using this jig without proper protective gear. Always wear safety glasses and a
Résumé du contenu de la page N° 14
Workpiece Basic Controls Inspection ON/OFF Control Valve Figure 6 ON Before shaping, inspect all workpieces OFF for the following: Material Type: Foreign Objects: Figure 6. Large/Loose Knots: Clamping Switches both Wet or "Green" Stock: Excessive Wa
Résumé du contenu de la page N° 15
Adjusting Airflow Adjustments Figure 8 Adjusting Clamp Height To adjust the cylinder bracket height: 1. Figure 9 Figure 8. Figure 9. 2. Important: The cylinder bracket must be fas- tened with the (6) M6-1 x 20 cap screws to operate safely. 3.
Résumé du contenu de la page N° 16
Positioning Workpiece Template Mounting Bracket Figure 12 Figure 10 Figure 12. Installing Templates Figure 10. To install the rear fence: Figure 13 1. 2. 3. Figure 11 Figure 13. Figure 11. Note: To install the coping fences simply reverse the above steps.
Résumé du contenu de la page N° 17
Miter Bar Rub Collar Figure 16 Figure 14. Figure 16. Figure 14. Clamping Workpiece ON. Figure 17 Always ensure that the jig base will clear the cutterhead or kickback could occur, caus- ing personal injury or property damage. Vertical Fence Figure 15 Figure 17. Figure 15.
Résumé du contenu de la page N° 18
Tip: To prevent tear-out in the workpiece Using Jig shape end grain first. Wood is less likely to tear while edge-shaping, so any tearout from end grain shaping can be removed. Use a sacrificial backing block between the workpiece and the coping fence as needed to further reduce tearout (see Figure 19). Tip: Use a practice piece similar to the workpiece in order to test the results before shaping the w
Résumé du contenu de la page N° 19
SECTION 4: ACCESSORIES 1 T23115— ⁄2" X 50' Hose Reel Some aftermarket accessories can be installed on this machine that could cause it to function improperly, increasing the risk of serious personal injury. To minimize this risk, only install accessories recommended for this machine by Grizzly. NOTICE Refer to the newest copy of the Grizzly Catalog for other accessories available for this machine. Figure 23. H7274—Pressure Regulator T10461—T10460 Arched Door Templates T10463—T10462
Résumé du contenu de la page N° 20
SECTION 5: MAINTENANCE Cleaning Always disconnect air to the jig before performing maintenance. Failure to do this may result in seri- ous personal injury. Schedule Lubrication Daily Check Weekly Maintenance SECTION 6: SERVICE Note: Please gather the serial number and manufacture date of your jig before calling. Troubleshooting