Résumé du contenu de la page N° 1
Owner's Manual
II:RRFTSMRN'I
RAILS AND FENCE SYSTEM
FOR CRAFTSMAN 10 in. TABLE SAWS MODEL NOS.
315.228310, 315.228410, 315.228510, 113.299310, 113.299410, 113.299510
Item No.
_929993
TABLE SAWNOT INCLUDED
Save this manual for
future reference.
• SAFETY
_, CAUTION: Read and follow
• LOOSE PARTS
all Safety Rules and Operating
Instructions before first use of
• PREPARATION
this product.
• INSTALLATION
• ALIGNMENT
Customer Help Line: 1-800-932-3188
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U
Résumé du contenu de la page N° 2
READ ALL INSTRUCTIONS • ALWAYS WEAR SAFETY GLASSES. Everyday eyeglasses have only impact-resistant lenses; • READ THESE INSTRUCTIONS AND THE they are NOT safety glasses. INSTRUCTIONS FOR YOUR TABLE SAW • ALWAYS DISCONNECT SAW FROM POWER THOROUGHLY before using accessories. SUPPLY BEFORE MAKING ADJUSTMENTS KNOW YOUR POWER TOOL. Read the owner's OR ADDING ACCESSORIES. Make sure the manual for the Table Saw carefully. Learn the switch is off when reconnecting to power supply, saw's applications and
Résumé du contenu de la page N° 3
SLOTFORBOLT TABLEEXTENSION REMOVING THE SWITCH AND RAILS • Remove the front rail end caps. • Under the front rail, loosen the switch screws and slide the switch off of the rail. See Figure 2. Note: Do not remove the switch screws completely. Loosening the screws will allow you to slide the switch off the front rail and the switch will be ready to install on the new front rail, REARRAIL __ FRONTRAIL _ TABLE SQUAREHEAD BOLT HEXNUT EXTENSION FLATWASHER Fig. 3 • Remove the rear rail end caps. • Unde
Résumé du contenu de la page N° 4
INSTALLING THE REAR RAIL • Position rail so that the right hand edge extends 2-1/2 in. beyond the table extension. A'_ WARNING: Front and rear rails must be Note: Instructions are given from the operator's carefully aligned to reduce the risk of kickback, position in front of the saw. which can cause serious injury. • Push the rail against table and tighten each hex nut with a 12 mm wrench. If the rail jams or does • From the carton, remove the rear rail and the not slide easily over the bolts,
Résumé du contenu de la page N° 5
INSTALLING THE FRONT RAIL RAILSLOT HEXNUT • Locate the front rail and the following hardware: Right and left end caps for front rail 2 screws (5/32-32 x 1/2 in.) for end caps • Set aside the end caps and two screws until the switch has been installed. Note: The square head bolts, washers, and hex nuts shown at the bottom of figure 6 should still be on the table saw. If you mistakenly removed them, put them back on the table. Do not tighten. • The back of the rail has two slots. See Figure SWITCH
Résumé du contenu de la page N° 6
P • Insert the two remaining pan head screws into \ FRONTRAIL holes in the fine adjustment knob bracket. TABLE • Attach the fine adjustment knob bracket to the EXTENSION bottom of the fence head on the right or the left side of the fence handle. Securely tighten the two screws. SWITCHSCREW BRACKET SWITCH ASSEMBLY SCREWS _ _ Fig. 10 Fig. 9 MOUNTING THE SWITCH ENDCAP • Locate the switch assembly, The fasteners should still be attached. Note: If the fasteners were removed from the switch, SCREW see
Résumé du contenu de la page N° 7
ALIGNING THE RIP FENCE AND FRONT RAIL • Remove the rip fence and repeat on the other side of the blade. When the fence rides smoothly, The rip fence scale indicator is installed on the right tighten all rail hex nuts with a 12 mm wrench. side of the rip fence but can be removed and rein- Push in the micro-adjust knob and turn it. The gear stalled on the left side if needed. If a cutting operation • on the shaft assembly will engage the rack teeth requires placing the rip fence on the left side o
Résumé du contenu de la page N° 8
MITERGAUGEGROOVE FRAMING CHECKING RIP FENCE AND. SQUARE BLADE ALIGNMENT The rip fence is self-aligning but should be checked before first use. _. WARNING: Failure to align the rip fence to the blade can cause jams and kickback, resulting in serious personal injury. • Slide the rip fence to the miter gauge groove, which is parallel to blade. Do not lock the rip fence. • Place a framing square against the blade, with the long end under the rip fence at the front. See Figure 14. Note the distance.
