Résumé du contenu de la page N° 1
OWNER’S MANUAL
INSTALLATION INSTRUCTIONS
®
WINEGARD
RV DIGITAL SATELLITE SYSTEM
with Digital Elevation Sensor
FOR WINNEBAGO INDUSTRIES
WI-DM04 - Single Coax Installation
WI-DM54 - Dual Coax Installation
U.S. PATENT NO. 5,532,710
Made in U.S.A.
Winegard Company • 3000 Kirkwood St. • Burlington, IA 52601-2000
319/754-0600 • FAX 319/754-0787 • www.winegard.com
Printed in U.S.A. © Winegard Company 2003, 2006 2451071 Rev5 12/12
Résumé du contenu de la page N° 2
POINT NORTH 240 250 290 300 310 320 330 340 350 OPERATION TUNING ANTENNA STEP 1. Step outside your vehicle and, using a compass, determine which direction is North. (Standing in or near vehicle can give you an STEP 1. Your receiver should indicate it is receiving a signal. To tune your incorrect reading.) The more accurately you determine North, the easier it will be to find the satellite(s). antenna for the best signal strength, slowly move the antenna left, then right until you have f
Résumé du contenu de la page N° 3
Center Roof Line Signal from satellite THINGS YOU NEED Screwdrivers (Phillips and slot) Non-hardening sealant ABS glue TROUBLE SHOOTING 1-3/4" hole saw (Check manufacturer’s specifications for Drill w/1/8" bit 7/16" wrench compatibility with your roof material) Tape measure 1. Be sure you have a clear line of sight. The signal from the satellite(s) 0 Antenna Reflector at 90 WILL NOT pass through trees, buildings,mountains etc. Remember 0 Winegard's Digital Elevation Sensor has b
Résumé du contenu de la page N° 4
(4) Antenna STEP 3. Assemble dish to backup using bolts and nuts provided, Mounting Bolts DIGITAL ELEVATION SENSOR ROOF CONNECTIONS Figure 4. STEP 4. Mount dish on roof in upright position. Rotate clockwise The illustrations below show the different methods of connecting wires at roof level. Method will depend on model. Wire colors to stop, Figure 5. Dish will be toward back of vehicle when in stowed MUST MATCH, ie. red to red, green to green, black to black or travel position. The word FRO
Résumé du contenu de la page N° 5
to compensate for roof/ceiling slope, be sure to allow for this extra thickness. You WITH ROOF WEDGE WITHOUT ROOF WEDGE may add an extension to the directional Measure from top Measure from top handle for thicker roofs. Each extension of roof wedge to ceiling. of roof to ceiling. will increase the length of the directional handle by 2-1/4". STEP 15. Press the directional handle TOP OF TOP OF onto the hub. Point the arrow on the ROOF WEDGE ROOF directional handle towards the ro
Résumé du contenu de la page N° 6
Roof Template ALIGN WITH BASEPLATE AREA MARKED “FRONT” POINT TO FRONT OF VEHICLE 1-3/4” DIA. DRILL COMPLETELY THROUGH CEILING 1/8” DRILL BIT 8 HOLES. DO NOT DRILL THROUGH CEILING.
Résumé du contenu de la page N° 7
POINT NORTH 240 250 290 300 310 320 330 340 350 FIGURE 13 CAUTION: After INITIAL INSTALLATION, the antenna SHOULD ROTATE APPROXIMATELY 360°FROM TRAVEL POSITION. The pointer on the DIRECTIONAL HANDLE should point towards the RED SCREW on the ROTATION CLAMP when in TRAVEL POSITION. ASSEMBLED VIEW Elevating Shaft Threaded Tube 3 Directional Handle Extension See template on reverse side. 1 Ceiling Plate POINTER Rotation MUST POINT Clamp 2 (4) #10 Phillips Flat TO RED Red Screw He
Résumé du contenu de la page N° 8
DIGITAL ELEVATION SENSOR INTERIOR WALLPLATE PARTS LIST Figure 14 Step 12. See Figure 14. If using the SM-1000 surface mount box, BACK VIEW feed cable through hole in box. Cable and plug from roof sen- STEP 13: Connect wires coming from sensor on sor unit; plugs roof to wall plate display in vehicle. It is important into sensor (2) 1/4-20 readout cable. Plastic Plug to properly connect the wires at the roof and the Hex Nut wall plate. (Plug will click when inserted properly.) The system i
Résumé du contenu de la page N° 9
PARTS LIST PARTS LIST Location of elevation sensor on backup, installed and calibrated at the factory INTERIOR Ceiling Base HARDWARE KIT Mounting RK-CEIL Screws Backup Directional Dial & Nuts Frame 46 cm Reflector, Sensor White Case Sensor Cable (4) #10 Phillip Flat Head Screws (4) Flat Head Bolts (White) Pins and Azimuth Lock LNBF E-clips LB-1000 Carriage Bolt (not shown) Azimuth Lock Knob Directional Flange Nut Handle Washer 1/4-20 Extension Backup Frame #10 x 3/8" Roller Feed Arm
Résumé du contenu de la page N° 10
SPECIFICATIONS NOTES ANTENNA & MOUNT Height when raised 30" verticle max. Height in the travel position 8" max. Operating radius 17" (34" diameter circle) Roof space required 26" ® ® LNB Compatible with DIRECTV , DISH , and Bell TV™ (northern U.S. and Canada) Weight 12 lbs. Color Cool gray Antenna height 20.9" Antenna width 19.2" F/D 0.59 o Offset angle 24 Frequency range 10.95 - 12.75 GHz Gain: 11.2 GHz 33.22 dBi 12.1 GHz 33.89 dBi 12.6 GHz 34.23 dBi Aperture e
Résumé du contenu de la page N° 11
WINEGARD MOBILE PRODUCTS LIMITED WARRANTY (2 YEARS PARTS; 1 YEAR LABOR) Winegard Company warrants this product against defects in materials or workmanship for a period of two (2) years from the date of original purchase. During year one (1) of such warranty, Winegard Company will also pay authorized labor costs to an authorized Winegard dealer to repair or replace defective products. No warranty claim will be honored unless at the time the claim is made, Customer presents proof of purchase
