Résumé du contenu de la page N° 1
OWNER’S MANUAL - OPERATION/INSTALLATION INSTRUCTIONS
®
WINEGARD
RV Digital Satellite System
with RS-1000 Antenna
TM
Model RM-4610, no Digital Magic Elevation Sensor
TM
Model RM-DM61 with Digital Magic Elevation Sensor
TM
Model RM-DM55 with Digital Magic (No Power Supply)
Made in U.S.A.
PARTS INCLUDED:
Reflector (dish)
Gasket
RS-1000 antenna
Interior parts
Mount/base assembly
Hardware
Models RM-DM61/DM55
Electronic elevat
Résumé du contenu de la page N° 2
OPERATION OPERATIONS DO’S AND DON’T’S FINDING THE SATELLITE TUNING ANTENNA FOR THE BEST PICTURE STEP 1. Step outside the vehicle and, using a compass, DO’S DON’T’S STEP 1. Your receiver should indicate it is receiving a determine which direction is North. (Standing in or near 1. Do check parking location for obstructions before rais- 1. Don’t move RV/Coach with the antenna in the UP signal. To tune your antenna, slowly move the antenna the vehicle can give you an incorrect reading.) The more
Résumé du contenu de la page N° 3
Signal from satellite INSTALLATION AND ASSEMBLY TROUBLE SHOOTING NO PICTURE ON TV THINGS YOU NEED Screwdrivers (Phillips and slot) 1. Do you have a clear line of sight to the satellite? Are Drill with 1/8” bit Sealant there trees, buildings, etc. in the way? Figure 3 illustrates 1-3/4” hole saw Tape measure (Must be approved for compatibility w/roof) the look angle of your reflector. 7/16” wrench FIGURE 3 2. Do you have the menu from the receiver? If not, check the channel the TV set is tuned
Résumé du contenu de la page N° 4
STEP 7. Facing the front of the dish, find coax cables STEP 3. Remove backing from gasket. Attach FIGURE 6 FIGURE 9 attached to side of the feed arm, Figure 9. Measure 24” adhesive side to base plate. IF YOU ARE of coax from this point and mark. DO NOT CUT. Rotate USING THE ROOF WEDGE (RW-5000), use mount on base clockwise, fully, until it stops. Route coax Measure coax 3/16” gasket included with the mount UNDER RS-1000 ANTENNA around mount base, Figure 10. 24” from plastic tie the roof
Résumé du contenu de la page N° 5
➤ FOR RM-DM61/RM-DM55 ONLY DIGITAL ELEVATION SENSOR ROOF CONNECTIONS The illustrations below show the different methods of connecting wires at roof level. Method will depend on model. Wire colors MUST MATCH (i.e. red to red, green to green, black to black, white to white). Supplied with the DM-2000 only. This wire harness connects to the digital elevation sensor on the antenna. Squeeze pliers until red 3M UR Terminal plunger is flush with rest of terminal. Slide wires all the way in. DO NOT
Résumé du contenu de la page N° 6
Roof Template ALIGN WITH BASEPLATE AREA MARKED “FRONT” POINT TO FRONT OF VEHICLE 1-3/4” DIA. DRILL COMPLETELY THROUGH CEILING 1/8” DRILL BIT 8 HOLES. DO NOT DRILL THROUGH CEILING.
Résumé du contenu de la page N° 7
STEP 19. The directional handle and threaded rod will fit roofs up WITH ROOF WEDGE WITHOUT ROOF WEDGE to 5-1/4” thick. If you are using Measure from top Measure from top wedges to compensate for roof/ of roof wedge to ceiling. of roof to ceiling. ceiling slope, be sure to allow for this extra thickness. You may add an extension to the directional handle for thicker roofs. Each ex- TOP OF TOP OF ROOF WEDGE ROOF tension will increase the length of the directional handle by 2-1/4”.
Résumé du contenu de la page N° 8
CAUTION: After INITIAL FIGURE 15 EXPLODED PARTS VIEW INSTALLATION, the antenna should ROTATE appRoximately 360° FROM TRAVEL POSITION. The pointer on the DIRECTIONAL HANDLE should point towards the RED SCREW on the ROTATION CLAMP when in TRAVEL POSITION. ASSEMBLED VIEW Elevating Shaft Threaded Tube 3 Directional Handle Extension 1 Ceiling Plate Rotation POINTER Clamp MUST POINT Red Screw 2 (4) #10 Phillips Flat TO RED Head Screws SCREW ON ROTATION 4 Directional Handle
Résumé du contenu de la page N° 9
PARTS LIST SPECIFICATIONS Height when raised ......... 30” with satellite antenna in vertical position INTERIOR Height in travel position ......... 8” Ceiling Base HARDWARE KIT Operating radius ......... 35” (70” diameter circle) RK-CEIL Directional Dial Roof space required ......... 19.5” x 46.75” ® ® LNBF ......... Compatible with DISH , DIRECTV and Bell TV™ Color ......... White Satellite antenna height ......... 20.9” Satellite antenna width ......... 19.5” (4) #10 Phillips Fla
Résumé du contenu de la page N° 10
REPLACEMENT PARTS KITS HEAD ASSEMBLY RP-RS00 TURRET ASSEMBLY RP-9500 Head w/bracket and nut .................1 Spring ............................................1 Pins ................................................2 Roll Pin ..........................................1 E-Clip .............................................2 Gear for worm shaft .......................1 Elevation gear ................................1 Bushing ..........................................2 REFLECTOR RP-REFL S
Résumé du contenu de la page N° 11
WINEGARD MOBILE PRODUCTS LIMITED WARRANTY (2 YEARS PARTS; 1 YEAR LABOR) Winegard Company warrants this product against defects in materials or workmanship for a period of two (2) years from the date of original purchase. During year one (1) of such warranty, Winegard Company will also pay authorized labor costs to an authorized Winegard dealer to repair or replace defective products. No warranty claim will be honored unless at the time the claim is made, Customer presents proof of purchase
