Résumé du contenu de la page N° 1
®
WINEGARD
TM
Movin’ View
Digital Satellite Mobile Antenna for Two Receivers
for Use While Stationary
Models MV3500A (White Dome)
MV3535A (Black Dome)
Made in the U.S.A. U.S. Patent Nos. 6,023,247; 6,188,300
Winegard Company • 3000 Kirkwood St. • Burlington, IA 52601-2000
319/754-0600 • FAX 319/754-0787 • www.winegard.com
Printed in U.S.A. © Winegard Company 2007 2452116 Rev3 1/10
1
HD-Ready
with the Winegard HD
Satellite Interface
(sold separately)
Résumé du contenu de la page N° 2
Introduction/How Does Digital Satellite TV Work? About this manual —We hope this manual will provide clear instructions to install and operate MV3500A. Two symbols have been used — Indicates suggestions to make Indicates caution should be taken! ! processes easier for you. ® Introduction DISH NETWORK - 1-800-333-DISH (1-800-333-3474) ® Congratulations! You have purchased one of Win- DIRECTV - 1-800-DIRECTV (1-800-347-3288) egard’s latest developments in the mobile satellite ® EXPRESSVU - 1
Résumé du contenu de la page N° 3
T C Quick Reference Guide NOTICE! ® This model is PRESET for DIRECTV receivers. ® ® If you have a DISH Network or ExpressVu (Canada) receiver, you must change the numbered switches inside the dome. TO CHANGE SWITCHES INSIDE DOME — 1. Remove screws holding dome to base and remove dome. Place dome in safe spot to avoid damage. ® Switches will be set at 101° for DIRECTV . You may be changing these switches. (#1 represents Switch DOWN; #0 represents Switch up) 1 2 3 4
Résumé du contenu de la page N° 4
To toggle between satellites when subscribing to multi-satellite programming— The MV3500A will toggle between the primary 5. Your system is now set up to toggle between and seconday satellites for either DISH Network satellites. It will automatically move to the correct or DIRECTV. Both have programming on more satellite when a channel is selected with your re- than one satelite. When a channel is selected on mote control. the remote control and is not on the satellite cur- rently select
Résumé du contenu de la page N° 5
Parts Included • Tools Needed • How to Unpack PARTS INCLUDED: All required screws, washers, bolts, and nylocks 1 Radome 1 base with electronics, dish, dual LNBF 1 Power switch 30’ Coax Cable 1 Wall plate (white) 30’ Power/Data Cable bundle 1 Surface mount box 1 Cable entry plate 4 Base feet large yellow flag connector 2 small red flag connectors TOOLS NEEDED FOR UNPACKING & INSTALLATION: Level 1/2” Drill bit Drill w/3/4” bit 7/16” Open end wrench 1-1/4” hole saw (if mounting switch in wall)
Résumé du contenu de la page N° 6
Installation Diagram SD i S e C of onTrol UT ni CT en er line of The MUST B P e ArAllel To vehiCle The CT en er line T of he vehiCle AnD f ACe fronT of vehiCle. or reAr of vehiCle. Control Unit LNBF ELEVATION MOTOR Used for Second Receiver (Not Included) Control Box detail CenT er line of The C vehi le Model MV3500A GPS ANTENNA (#1 represents Switch DOWN; #0 represents Switch up) (RoadTrip SDi In-Motion Sat. Rcvr. Switch Set Position models ONLY)
Résumé du contenu de la page N° 7
Installation Installing unit on roof of vehicle — 3. After selecting location for unit (see number 2), Install in DRY conditions only! ! put the unit on the centerline of the vehicle. IMPORTANT! Do not install this system 4. Position base so that cables exit toward the rear in the rain, or under any wet conditions. Mois- of the vehicle. Electronics box should be parallel ture may affect electronics and void your warranty! to the centerline of the vehicle. 1. For best performance and to
Résumé du contenu de la page N° 8
Installation Cable entry installation — INSTALLING THE POWER SWITCH 1. Decide the best location for the cables to enter the 1. Choose a location to install the Movin’ View power vehicle, and the location of the power switch and ON/OFF switch. Remember when selecting a location receiver (see “Installing the switch and receiver”on that you will need to run the +12VDC power cable from pages 9 and 10). Drill a 1/2” hole in the roof, push the Movin’ View antenna to the switch. be sure the
Résumé du contenu de la page N° 9
Installation • Wiring Initializing & replacing the dome after Connecting the receiver — connecting the receiver(s) — Connecting one receiver 1. Be sure that switch settings have been made ac- 1. Connect the coax cable from the MV3500A to cording to your service provider. See page 3. the “SATEllITE IN” on the receiver. 2. Be sure vehicle is in a location free of all obstruc- tions and with a clear view of the satellite. 3. Power up unit, turn on receiver. Verify that the Connecting two rece
Résumé du contenu de la page N° 10
Troubleshooting SOLUTION PROBLEM The MV3500A does not attempt to find a satellite or 1. Check your Power switch to verify that it is in the ON position. it never moves. 2. Check +12 V wires at unit to verify power. Check fuse on electronics. The dish never stops on any of the signals that 1. Make sure that your receiver is set up correctly. it sees. For DISH Network, the check switch should read either “Unknown” or “SW42”. For DirecTV the receiver should be set for a Two
Résumé du contenu de la page N° 11
Specifications & W arranty Features and specifications • One button operation. • Dome UV protected. • Depending on receiver type, you can access • Compact size — satellites 119°, 110°, 101° or 92°. 32” diameter, 15-3/4” height Weight of unit - 28 lbs. • No user input required. Shipping weight - 41 lbs. ® • No data port required for DISH Network , • Operating temperature ® DIRECTV or ExpressVu. -13°F to +140°F • Elevation range 18° to 74.5°; • Wired for use with the W
Résumé du contenu de la page N° 12
Winegard Company • 3000 Kirkwood Street • Burlington, IA 52601 • 319/754-0600 Fax 319/754-0787 • www.winegard.com Printed in U.S.A. © 2007 Winegard Company 2452116 Rev3 1/10 12
