Résumé du contenu de la page N° 1
www.sauservice.com
Satellite Installation Manual
SEGA AMUSEMENTS USA INC.
Résumé du contenu de la page N° 2
SECURING THE SATELLITE PLACEMENT POSITIONS 2 Be sure that all adjusters are placed against the floor. Failure to place the adjusters against the floor could lead to accidents caused by cabinet movement. WARNING! Each satellite is equipped with 4 adjusters and 4 casters. When the placement position has been determined, place the adjusters directly against the floor and perform adjustments to make the satellite horizontally level. ADJUSTERS 1 Move the satellite to the placement position. 2
Résumé du contenu de la page N° 3
3 Place all the adjusters against the floor. Use a wrench to adjust the height of the adjusters so that the satellite is horizontally level. 4 Following adjustment, tighten the nut on each adjuster to fix the height. Fasten upward. Be sure to make contact with the surface. PHOTO 6. 2 b 5 Replace the 4 covers at the corners. FIG 6. 2 b Refer to this figure (scale: 1/100) for the layout of the place of installation. 6 Follow the procedure below to attach the instruction plate and the
Résumé du contenu de la page N° 4
POWER SUPPLY, AND EARTH CONNECTION 3 ● Be sure to independently use the power supply socket outlet equipped with an Earth Leakage Breaker. Using a power supply without an Earth Leakage Breaker can cause a fire when electric leakage occurs. WARNING! ● This product is designed for an electrical outlet with an earth element. The power cord incorporates an earth wire. Improper grounding could result in electrical shock to customers, damage to components, and/or malfunctioning. ● If an ele
Résumé du contenu de la page N° 5
9 Ensure that the main switch is OFF. MAIN SW CIRCUIT PROTECTOR Main SW off AC Cable (Power Cord) INLET EARTH TERMINAL (for TAIWAN) Connect with the indoor earth terminal. FIG. 6. 3 b AC UNIT OF THE MAIN PROJECTION UNIT CIRCUIT PROTECTOR(10A)(For TAIWAN) (For Service outlet) SERVICE OUTLET (For TAIWAN) EARTH TERMINAL (For TAIWAN) Connect to the AC COVER indoor earth terminal. INLET POWER SW OFF. CIRCUIT PROTECTOR(5A) POWER SWITCH FIG. 6. 3 c AC UNIT OF THE SATELLITE 10 Firmly insert the
Résumé du contenu de la page N° 6
11 Connect the earth wire to the earth terminal. One end of the earth wire should be connected to the product's earth terminal, and the other end to an indoor earth terminal. The earth terminal of the AC unit consists of a bolt and nut set. First remove the nut, then place the end of the earth wire so that the bolt passes through, and finally tighten the nut. (For TAIWAN) *Note that the earth wire is incorporated in the power cord for the areas of AC 120V FIG. 6. 3 d *Earth Wi
Résumé du contenu de la page N° 7
COMMUNICATION CONNECTIONS 4 The communication cables are fiber optic type cables, and should be handled STOP carefully. Improper handling may result in damage (such as from folding) that would render them unusable. IMPORTANT! Do not place heavy objects on the cables or step on them. When connecting or disconnecting the cables and connectors, always hold the connectors. Do not hold the cables. Be careful not to allow the connection surfaces at the ends of the communica- tion cables
Résumé du contenu de la page N° 8
3 Open the cover of the satellite AC AC UNIT COVER unit. 4 Remove the fiber guide plate by removing the 2 screws. FIBER GUIDE PLATE PHOTO 6. 4 b 5 Run the 2 communication cables through the satellite. Run the cables from the bottom of the satellite, past the depth-wise side of the sheet metal in front of the AC unit, and pass them into the satellite through the square holes revealed by removing the fiber guide plate. Run the two communication cables through the Satellite. Co
Résumé du contenu de la page N° 9
7 Secure the communication cable Use the cord clamp inside the satellite by using the cord clamp. to secure the communication cables (Photo 6. 4 e). 8 Near the cable exit, make loops in the communication cables with a diameter of at least 6 cm. Use the repeat tie belt to secure the looped communication cables (Figure 6. 1 l). FIBER GUIDE PLATE PHOTO 6. 4 e 9 Run the communication cables through the slit on the fiber guide plate (Photo 6. 4 f). 10 Secure the fiber guide pla
Résumé du contenu de la page N° 10
DIAGRAM EXPLAINING COMMUNICATION CABLE CONNECTIONS The diagram below illustrates an example of communication cable usage. Communication cables of appropriate lengths should be used in accordance with satellite layout. www .seuservice.com www .seuservice.com 42 43
Résumé du contenu de la page N° 11
SETTING THE CARDS 5 ● Please be sure to use the proprietary cards for this product. Usage of other STOP cards could cause malfunctioning or breakdown. ● Be sure to set the cards in accordance with the specified procedure, direction, IMPORTANT! and number. Incorrect setting could cause equipment breakdown or other problems. ● Up to 100 cards may be set at a time. Do not set more than 100 cards, as this could cause problems such as jamming. ● Use new, freshly opened cards. Use of defor
Résumé du contenu de la page N° 12
3 Place the cards in the dispenser in accordance with the instructions on the sticker that appears on the dispenser. Be careful not to place the cards backwards or upside down. The number of cards that can be placed in the dispenser at any one time is 100. In order to avoid problems such as jamming, be sure not exceed this limit. Use new packages of 100 cards, or else carefully count the number of cards before placing them in the dispenser. Us e the s ticker on top of the dis pens er to
Résumé du contenu de la page N° 13
Option Settings Main Board Settings 1. Press the test button on the Satellite to enter the main test mode. 2. Move cursor to Game test Mode. Press the test button to enter the Game Test. 3. Move the cursor to Game Assignments. Press Test Button to enter. 4. Move cursor to "Number of Satellites". Press test to change to the proper number (4-8). Note: Do not change the "Race Mode" while setting the number of satellites. 5. Exit the menu. 6. Exit Game test menu, and then the Main System menu
Résumé du contenu de la page N° 14
DOC Satellite Pedestal Assy � � � � � ��� � Item Part Number Description 1 601-11202 Carpet 1155x11545 Gray SHE-M003 2 601-11112 Seat Stopper DOC-M007 for SHE 3 105-5464 Corner Edge L1249 SCR Type DOC 4 105-5466 Corner Edge SCR Type DOC 5 105-5465 Corner Edge L859 SCR Type DOC 201 000-T00630-0C M SCR TH CRM M6x30
