Résumé du contenu de la page N° 1
LevelOne
User Manual
WBR-3600
11g Wireless ADSL2+ Router
V1.0.0-0803
Résumé du contenu de la page N° 2
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarant
Résumé du contenu de la page N° 3
Table of Contents CHAPTER 1 INTRODUCTION ......................................................................................1 WBR-3600 Router Features..................................................................................1 Package Contents.................................................................................................4 Physical Details.....................................................................................................5 CHAPTER 2 INSTALLATION
Résumé du contenu de la page N° 4
Remote Administration.......................................................................................82 Routing.................................................................................................................84 Upgrade Firmware ..............................................................................................88 CHAPTER 8 MODEM MODE ......................................................................................89 Overview ...........................
Résumé du contenu de la page N° 5
Chapter 1 Introduction 1 This Chapter provides an overview of the WBR-3600 Router's features and capabilities. Congratulations on the purchase of your new WBR-3600 Router. The WBR-3600 Router is a multi-function device providing the following services: • ADSL2+ Modem. • Shared Broadband Internet Access for all LAN users. • Wireless Access Point for 802.11b and 802.11g Wireless Stations. • 4-Port Switching Hub for 10BaseT or 100BaseT connections. Figure 1: Wireless ADSL2+ Router W
Résumé du contenu de la page N° 6
• Auto-detection of Internet Connection Method. In most situations, the Wireless ADSL2+ Router can test your ADSL2+ and Internet connection to determine the connection method used by your ISP. • Fixed or Dynamic IP Address. On the Internet (ADSL port) connection, the Wireless ADSL2+ Router supports both Dynamic IP Address (IP Address is allocated on connection) and Fixed IP Address. Advanced Internet Functions • Application Level Gateways (ALGs). Applications which use non-standard
Résumé du contenu de la page N° 7
• Simple Configuration. If the default settings are unsuitable, they can be changed quickly and easily. • WPS Support. Wi-Fi Protected Setup (WPS) is based on push-button or PIN entry authentication to provide strong WPA/WPA2 encryption keys to client devices. LAN Features • 4-Port Switching Hub. The Wireless ADSL2+ Router incorporates a 4-port 10/100BaseT switching hub, making it easy to create or extend your LAN. • DHCP Server Support. Dynamic Host Configuration Protocol provides
Résumé du contenu de la page N° 8
Package Contents The following items should be included. If any of these items are damaged or missing, please contact your dealer immediately. • WBR-3600 • Power Adapter • Antenna • Cat.5 Cable • CD Manual • Quick Installation Guide 4
Résumé du contenu de la page N° 9
Physical Details Front-Panel LEDs Figure 2: Front Panel PWR On - Power on. Off - No power. WLAN On - Wireless enabled. Off - No Wireless connections currently exist. Flashing - Data is being transmitted or received via the Wireless access point. This includes "network traffic" as well as user data. LAN It indicates the connection of each port. If neither LED is on, there is no active connection on the corresponding LAN port. ADSL On - ADSL connection established. Off - No AD
Résumé du contenu de la page N° 10
Rear Panel Figure 3: Rear Panel WAN Connect this port to your ADSL line. LAN Use standard LAN cables (RJ45 connectors) to connect your PCs to these ports. Note: Any LAN port on the Wireless ADSL Router will automatically function as an "Uplink" port when required. Just connect any port to a normal port on the other hub, using a standard LAN cable. Reset Button This button will reset the Wireless ADSL2+ Router to the factory default settings. (Reset to To do this, press and hol
Résumé du contenu de la page N° 11
Chapter 2 Installation 2 This Chapter covers the physical installation of the Wireless ADSL2+ Router. Requirements • Network cables. Use standard 10/100BaseT network (UTP) cables with RJ45 connectors. • TCP/IP protocol must be installed on all PCs. • For Internet Access, an Internet Access account with an ISP, and a DSL connection. • To use the Wireless Access Point, all Wireless devices must be compliant with the IEEE 802.11g or IEEE 802.11b specifications. Procedure Figure 4:
Résumé du contenu de la page N° 12
2. Connect LAN Cables Use standard LAN cables to connect PCs to the Switching Hub ports on the Wireless ADSL2+ Router. Both 10BaseT and 100BaseT connections can be used simultaneously. If required, connect any port to a normal port on another Hub, using a standard LAN cable. Any LAN port on the Wireless ADSL2+ Router will automatically function as an "Uplink" port when required. 3. Connect ADSL Cable Connect the supplied ADSL cable from to the ADSL port on the Wireless ADSL2+ Router (
Résumé du contenu de la page N° 13
Chapter 3 Setup 3 This Chapter provides Setup details of the WBR-3600 Router. Overview This chapter describes the setup procedure for: • Internet Access • LAN configuration • Wireless setup • Assigning a Password to protect the configuration data. PCs on your local LAN may also require configuration. For details, see Chapter 4 - PC Configuration. Other configuration may also be required, depending on which features and functions of the WBR-3600 Router you wish to use. Use the tab
Résumé du contenu de la page N° 14
Use any of the following Administration Configuration Chapter 7 settings or features: Advanced Administration • PC Database • Config File • Logs • E-mail • Diagnostics • Remote Admin • Routing • Upgrade Firmware 10
Résumé du contenu de la page N° 15
Configuration Program The WBR-3600 Router contains an HTTP server. This enables you to connect to it, and configure it, using your Web Browser. Your Browser must support JavaScript. The configuration program has been tested on the following browsers: • Netscape 7.1 or later. • Mozilla 1.6 or later • Internet Explorer V5.5 or later Preparation Before attempting to configure the WBR-3600 Router, please ensure that: • Your PC can establish a physical connection to the WBR-3600 Router. T
Résumé du contenu de la page N° 16
If you can't connect If the WBR-3600 Router does not respond, check the following: • The WBR-3600 Router is properly installed, LAN connection is OK, and it is powered ON. You can test the connection by using the "Ping" command: • Open the MS-DOS window or command prompt window. • Enter the command: ping 192.168.0.1 If no response is received, either the connection is not working, or your PC's IP address is not compatible with the WBR-3600 Router's IP Address. (See next item.) • I
Résumé du contenu de la page N° 17
Setup Wizard The first time you connect to the WBR-3600 Router, you should run the Setup Wizard to configure the ADSL and Internet Connection. 1. Click the Setup Wizard link on the main menu 2. On the first screen, select VC 1 (Router - Primary Internet Connection), then click "Next" Figure 5: Setup Wizard Home Page 3. On the VC1 screen, shown below, enter the VPI and VCI values provided by your ISP, then click "Next". Figure 6: Setup Wizard - VC1 13
Résumé du contenu de la page N° 18
Figure 7: Setup Wizard - Internet Access 4. On the Internet Access Screen, shown above, select the correct connection type, as used by your ISP. Click "Next" and complete the configuration for your connection method. • You need the data supplied by your ISP. Your ISP's data will also have the DSL Multiplexing Method ( LLC or VC ) • The common connection types are explained in the following table.. Connection Details ISP Data required Type Dynamic Your IP Address is allocated Often
Résumé du contenu de la page N° 19
5. Step through the Wizard until finished. 6. On the final screen of the Wizard, run the test and check that an Internet connection can be established. 7. If the connection test fails: • Check all connections, and the front panel LEDs. • Check that you have entered all data correctly. 15
Résumé du contenu de la page N° 20
Configuring VCs The WBR-3600 Router supports multiple VCs (Virtual Circuits) on the ADSL connection. VC1 must be used for general-purpose Internet access. The other VCs are available for special purposes, such as Video-on-Demand. You can only use these VCs if supported by your ISP and ADSL service provider. In that case, they will provide the necessary configuration data. Some ISP's allow multiple PPPoE connections. This allows multiple PCs to connect to the Internet using PPPoE cl
