Résumé du contenu de la page N° 1
2001 - 2005
Keyless Entry System Remote Control Transmitter
Résumé du contenu de la page N° 2
Contents Introduction ....................................................................................3 Precautions ....................................................................................4 Remote Control Transmitter Controls and Functions .............................................................6 Battery Replacement ................................................................8 Remote Control Code Programming How to Program Remote Control Transmitters ....................
Résumé du contenu de la page N° 3
Introduction Congratulations on your purchase of this Honda Keyless Entry This device complies with FCC Rules Part 15. Operation is subject System. to the following two conditions: (1) This device may not cause Your Honda Keyless Entry System is the product of years of harmful interference and (2) This device must accept any research and development. It will give you many years of reliable interference that may be received including interference that may performance, protection, and convenience.
Résumé du contenu de la page N° 4
Precautions Remote Control Range Temperature Several factors affect and reduce Avoid exposing the remote remote control range. Among control transmitter to extreme hot these are: or cold weather conditions. 1. Proximity to buildings and automobiles. 2. Proximity to high power transmitters (television, radio, cellular, HAM radio, etc.). 3. When the battery becomes weak, the remote control range becomes short. Vehicle construction and the Liquids surrounding environment cause Never submerge the Re
Résumé du contenu de la page N° 5
Precautions In Case of Loss Battery Power Use the remote control transmitter If one of your remote control transmitters is ever lost, contact your only when necessary. local Honda dealer for a replacement. Your system will be Every time a button is pressed, reprogrammed to prevent the lost remote control transmitter from the remote control is consuming operating your system. In this case, take all the other remote control battery power. transmitters to have them reprogrammed. If battery is low o
Résumé du contenu de la page N° 6
Remote Control Transmitter • The doors cannot be locked or unlocked with the remote control transmitter when the key is in the ignition switch. Controls and Functions • The doors cannot be locked if any one of the doors is open. • The panic mode will not work when the ignition switch is turned ON. LOCK Button 1 When used alone, this button locks the doors and flashes the parking lights once. Note: If the lock button is pressed for a second time (within 5 seconds of the first push) the horn will
Résumé du contenu de la page N° 7
Remote Control Transmitter PANIC Button 3 When this button is pressed and held for more than 1 second, the keyless entry system is set to the panic mode. 4 The horn will sound for 30 seconds and the parking light and headlights will flash. To deactivate the panic mode, press the "LOCK", "UNLOCK" or "PANIC" button or turn the ignition key to the "ON" ( ) position. Signal Indicator LED 4 The LED will light when a remote control 3 button is pushed and the remote control is transmitting a control s
Résumé du contenu de la page N° 8
Remote Control Transmitter Battery Replacement The remote control transmitter requires one lithium battery (#CR2025). Using a coin (Quarter) turn the battery cover counterclockwise and remove the cover from the 1 back of the remote control. Remove the used battery. Make sure you install the new battery with the proper polarity. 2 Note: If the Lithium battery is incorrectly placed (+ and – polarity), the Remove Control Transmitter can be damaged. Replace the battery cover. Use a coin to turn i
Résumé du contenu de la page N° 9
Remote Control Code Programming • For steps 2 through 12, each step must be completed within 5 seconds. For step 13, How to Program Remote within 10 seconds for each remote. • Up to 3 remotes can be stored in memory. Control Transmitters • All remotes to be programmed must be on hand. • A non programmed remote will work for this procedure. • Turn the ignition key to the "OFF" position to complete the programming procedure. Unlock the doors. 1 Turn the ignition key to the "ON" ( ) 2 position.
Résumé du contenu de la page N° 10
Remote Control Code Programming Press the "LOCK" or "UNLOCK" button on 6 the remote control transmitter. Turn the ignition to the "OFF" (0, ) position. 7 Turn the ignition to the "ON" ( ) position. 8 6 9 Press the "LOCK" or "UNLOCK" button on 9 the remote control transmitter. Turn the ignition to the "OFF" (0, ) position. 10 Turn the ignition to the "ON" ( ) position. 11 10
Résumé du contenu de la page N° 11
Remote Control Code Programming Press the "LOCK" or "UNLOCK" button on 12 the remote control transmitter. • The power door locks cycle to indicate programming mode. 13 • To terminate the programming mode at this point, either turn the ignition key to the "OFF" position or leave the remote’s 12 button untouched for over 10 seconds. To program the remote, perform steps 2 through 12. Press the "LOCK" button of each remote 13 (one at a line) to be stored in memory. • The power door locks cycle to co
Résumé du contenu de la page N° 12
AAM39211 Specifications Remote Control Transmitter Transmitter Type ............................................................................................. Radio frequency Range ............................................................................................................ Maximum 30 feet Battery Type ............................................................................................... Lithium (# CR2025) Battery Life ..................................................
