Résumé du contenu de la page N° 1
GAS HOB
ZGL 62
INSTRUCTION BOOKLET
Please read this instruction booklet before using the appliance
GB
Résumé du contenu de la page N° 2
Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 727727 Installation Perishable food, plastic items and aerosols may be affected by heat and should not be stored above or This appliance must be installed and serviced by a below the hob unit. competent person as stated in the Gas Safety ( Installation and Use) Regulations Current Editions and the IEE Wiring Regulations.
Résumé du contenu de la page N° 3
Contents For the Installer For the User Instructions for the Installer 8 Important Safety Information 2 Installation 10 Description of the Hob 3 Electrical connections 12 Operation 4 Wiring Diagram 13 Maintenance and Cleaning 5 Something Not Working? 6 Fault Finding 13 Service and Spare Parts 6 Commissioning 15 Customer Care 7 Conversion from Natural Gas to LPG 15 Guarantee Conditions 7 This appliance complies with the following E.E.C. Directives: * 73/23 - 90/683 (Low VoltageDirective); * 93/68
Résumé du contenu de la page N° 4
Operation Hob burners To light a burner: turn the relevant control knob anticlockwise to the maximum position, then push it down to ignite the burner; then, check the flame is regular and adjust it as required. If you cannot light the flame even after several attempts, check the "cap" and “crown” (see diagram - letter A and B) are in the correct position. To put the flame out, turn the knob to the symbol . When switching on the mains, after installation or a power cut, it is quite norma
Résumé du contenu de la page N° 5
Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little washing up liquid has been added. Avoid the use of the following: - household detergent and bleaches; - impregnated pads unsuitable for n
Résumé du contenu de la page N° 6
Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Zanussi Service Force Centre. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee. SYMPTOM SOLUTION There is no spark when lighting the gas Check that the unit is plugged in and the electrical supply is switched on Check that th
Résumé du contenu de la page N° 7
Customer Care Department For general enquiries concerning your Zanussi appliance or for further information on Zanussi products, please contact our Customer Care Department by letter or telephone at the address below or visit our website at www.zanussi.co.uk Customer Care Department ZANUSSI 55-77 High Street Slough Berkshire SL1 1DZ 08705 727727 (*) * calls to this number may be recorded for training purposes. Guarantee Conditions Zanussi Guarantee conditions We, Zanussi, undertake that if, with
Résumé du contenu de la page N° 8
Instructions for the Installer Engineers technical data Overall dimensions Rear Left Burner (semi rapid) Heat Input 2.0 kW (6824 BTU/HR) Width: 580 mm Depth: 500 mm Front Left Burner (rapid) Heat Input 3.0 kW Natural gas (10236 BTU/HR) Cut out dimensions 2.8 kW L.P.G. (9554 BTU/HR) Width: 550 mm Rear Right Burner (semi rapid) Depth: 470 mm Heat Input 2.0 kW (6824 BTU/HR) Supply connections Front Right Burner (auxiliary) Gas: Heat Input 1.0 kW (3412 BTU/HR) RC 1/2 inch (1/2 inch male) Rear right
Résumé du contenu de la page N° 9
50 mm 100 mm 50 mm 100 mm 50 mm 50 mm 600 mm Important safety requirements This hob must be installed in accordance with the Gas Location Safety (Installation and Use) Regulations (Current Edition) The hob may be located in a kitchen, a kitchen/diner or and the IEE Wiring Regulations (Current Edition). bed sitting room, but not in a bathroom, shower room or garage. Provision for ventilation Before making the cut out in the worktop ensure that Detailed recommendations are contained in the followi
Résumé du contenu de la page N° 10
Installation IMPORTANT: This hob must be installed by a competent person to the relevant Gas Standards. Please, ensure that, once the hob is installed, it is easily accessible for the engineer in the event of a breakdown. WHEN THE HOB IS FIRST INSTALLED Once the hob has been installed, it is important to remove any protective materials, which were put on in the factory. Any gas installation must be carried out by a competent person. The manufacturer will not accept liability, should the above i
Résumé du contenu de la page N° 11
Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it It is also recommended to carry out the electrical will be necessary to fit a heat resistant board below the connection to the hob as shown in diagrams 1 and 2. base of the hob on the underside of the work surface. 1 2 3 ON/OFF SWITCH ON/OFF SWITCH a 60 FLEX OUTLET b FLEX OUTLET FO 0763 FO 0764 FO 1013 Dimensions are given in mm. Building over a kitchen unit with door Proper arrangements mu
Résumé du contenu de la page N° 12
Electrical connections Any electrical work required to install this hob Permanent Connection should be carried out by a qualified electrician or In the case of a permanent connection, it is necessary competent person, in accordance with the current that you install a double pole switch between the hob regulations. and the electricity supply (mains), with a minimum gap of 3 mm. between the switch contacts and of a type THIS HOB MUST BE EARTHED. suitable for the required load in compliance with th
Résumé du contenu de la page N° 13
Wiring Diagram A. TAPS IGNITOR SWITCHES B. IGNITOR UNIT Fault Finding Preliminary Electrical Systems Check SOCKET PLUG (with cover removed) (face view) Earth Wire ( ) Green/Yellow ( ) E Brown Blue START Neutral Wire Isolate appliance Blue and carry out: A: Earth Continuity N L check. Blue Green Brown Yellow Carry out: Electricity supply NO YES Carry out: D: Resistance to should now be C: Polarity check. Earth check. satisfactory. A. EARTH CONTINUITY CHECK - Appliance must Has inlet fuse blo
Résumé du contenu de la page N° 14
Ignition System / Gas Ignition YES Check gas supply at Ignitor does not spark burner NO Check plug top fuse and Light burner manually replace if necessary Check by pass Check polarity and simmer earth continuity of supply point Check position of the Check earth continuity electrode of appliance Check continuity from the tip Check fitting of burners Check continuity from 'N' on the of each electrode to the mains connector block and "O" on terminals 1 to 4 on the ignitor the ignitor unit unit Chec
Résumé du contenu de la page N° 15
Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. - Turn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguished follow the procedure below. Procedure: - Re-ignite the burner and set to MIN. - Remove the control knob and use a thin bladed screwdriver to turn the ad
Résumé du contenu de la page N° 16
CUSTOMER CARE ZANUSSI 55-77 High Street Slough Berkshire, SL1 1DZ Tel: 08705 727727 Long Mile Road Dublin 12 Republic of Ireland Tel: + 353 (0) 1 4090751 © Electrolux plc 2003 From the Electrolux Group. The world’s No.1 choice. The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are so
