Résumé du contenu de la page N° 1
INSTALLATION INSTRUCTIONS
20" (50.8 CM) FREESTANDING GAS RANGE
with Standard Clean Oven
Table of Contents
RANGE SAFETY............................................................................. 2
INSTALLATION REQUIREMENTS ............................................... 4
Tools and Parts............................................................................ 4
Location Requirements ............................................................... 4
Electrical Requirements.....................
Résumé du contenu de la page N° 2
RANGE SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These words mean: You can be killed or seriously injured if you don't immediately DANG
Résumé du contenu de la page N° 3
In the State of Massachusetts, the following installation instructions apply: ■ Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by the State of Massachusetts. ■ If using a ball valve, it shall be a T-handle type. ■ A flexible gas connector, when used, must not exceed 3 feet. WARNING Tip Over Hazard A child or adult can tip the range and be killed. Install anti-tip bracket to floor or wall per installation instruct
Résumé du contenu de la page N° 4
INSTALLATION REQUIREMENTS Tools and Parts Location Requirements Gather the required tools and parts before starting installation. IMPORTANT: Observe all governing codes and ordinances. Do Read and follow the instructions provided with any tools listed not obstruct flow of combustion and ventilation air. here. ■ It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The Tools needed model/serial rating plate is located on the ov
Résumé du contenu de la page N° 5
Product Dimensions Cabinet Dimensions Freestanding Range Cabinet opening dimensions shown are for 25" (64.0 cm) countertop depth, 24" (61.0 cm) base cabinet depth and 36" (91.4 cm) countertop height. If the cabinet depth is greater than 24" (61.0 cm), oven frame must extend beyond cabinet fronts by ½" (1.3 cm) minimum. D B C 41¹¹⁄₁₂" (106.6 cm) A E H G J I F K 25⁷⁄₈" 19³⁄₄" M (65.9 cm) L (50 cm) N L A. 18" (45.7 cm) min. clearance upper side cabinet to countertop B. 13" (33.0 cm) max. upper c
Résumé du contenu de la page N° 6
Electrical Requirements Gas Supply Requirements WARNING WARNING Electrical Shock Hazard Explosion Hazard Plug into a grounded 3 prong outlet. Use a new CSA International approved gas supply line. Do not remove ground prong. Install a shut-off valve. Do not use an adapter. Securely tighten all gas connections. Do not use an extension cord. If connected to LP, have a qualified person make sure gas pressure does not exceed 14" (36 cm) water Failure to follow these instructions can result in death
Résumé du contenu de la page N° 7
Flexible metal appliance connector: Gas Pressure Regulator ■ If local codes permit, a new CSA design-certified, 4-5 ft (122-152.4 cm) long, ½" (1.3 cm) or ¾" (1.9 cm) I.D., The gas pressure regulator supplied with this range must be flexible metal appliance connector may be used for used. The inlet pressure to the regulator should be as follows for connecting range to the gas supply line. proper operation: Natural gas: Minimum pressure: 5" WCP Maximum pressure: 14" WCP ■ A ½" (1.3 cm) male
Résumé du contenu de la page N° 8
INSTALLATION INSTRUCTIONS 2. Determine which mounting method to use: floor or wall. If you have a stone or masonry floor, you can use the wall Unpack Range mounting method. If you are installing the range in a mobile home, you must secure the range to the floor. WARNING 3. Determine and mark centerline of the cutout space. The mounting can be installed on either the left side or right side Excessive Weight Hazard of the cutout. Position mounting bracket against the wall in the cutout so tha
Résumé du contenu de la page N° 9
Make Gas Connection 3. Use a combination wrench and pliers to attach the flexible connector to the adapters. Check that connector is not kinked. WARNING A B D Explosion Hazard C Use a new CSA International approved gas supply line. F Install a shut-off valve. E Securely tighten all gas connections. G If connected to LP, have a qualified person make sure H gas pressure does not exceed 14" (36 cm) water column. Examples of a qualified person include: A. Pressure regulator E. Adapter connectio
Résumé du contenu de la page N° 10
5. Close the broiler door. IMPORTANT: If there is a snapping or popping sound when lifting the range, the range may not be fully engaged in the bracket. 6. Remove cooktop burner caps and grates from parts Check to see if there are obstructions keeping the range from package. Align notches in burner caps with pins in burner sliding to the wall or keeping the range foot from sliding into the base. Burner caps should be level when properly positioned. bracket. Verify that the bracket is held
Résumé du contenu de la page N° 11
Check Operation of Cooktop Burners Check Operation of Oven/Broil Burner 1. If control panel and knobs were removed earlier, reinstall 1. Open broiler door. knobs. 2. Press in and turn the oven control knob to 350°F. 2. Push in and turn each surface unit control knob to the “LITE” position. The flame should light within 4 seconds. ■ The oven pilot should now be larger with the flame burning against a small metal bulb. 3. Turn control knob to the “HI” position after burner lights. ■ The oven b
Résumé du contenu de la page N° 12
7. Tighten the shutter screw. If range does not operate, check the following: 8. Reinstall flame spreader and oven tray. Reinstall the oven ■ Household fuse is intact and tight, or circuit breaker has not racks. tripped. 9. Close the oven door. ■ Range is plugged into a grounded 3 prong outlet. 10. Close the broiler door. ■ Electrical supply is connected. ■ See the “Troubleshooting” section of the Use and Care Complete Installation Guide. 1. Check that all parts are now installed. If there is
Résumé du contenu de la page N° 13
3. Open broiler door and remove broiler pan. The gas pressure 3. Remove Natural gas orifice spuds using a 7 mm combination regulator is located in the back right hand corner of the broiler wrench. compartment. 4. Install LP gas orifice spuds using a 7 mm combination wrench. A A. Gas pressure regulator A IMPORTANT: Do not remove the gas pressure regulator. 4. Remove the cap from the gas pressure regulator using a flat-blade screwdriver. NOTE: Do not remove the spring beneath the cap. B A A. Sp
Résumé du contenu de la page N° 14
To Convert Oven Burner Natural Gas Conversion 1. Open the oven door and remove oven racks, oven tray and flame spreader and set aside. WARNING 2. Lift oven burner. The orifice spud is behind the oven burner air shutter. Tip Over Hazard A B A child or adult can tip the range and be killed. Install anti-tip bracket to floor or wall per installation instructions. A. Oven burner B. Air shutter Slide range back so rear range foot is engaged in the slot of the anti-tip bracket. 3. Locate LP gas or
Résumé du contenu de la page N° 15
4. Remove the cap from the gas pressure regulator using a 4. Install the Natural gas orifice spuds using a 7 mm flat-blade screwdriver. combination wrench. NOTE: Do not remove the spring beneath the cap. A A A. Cap 5. Turn the cap over so that N or NAT is visible. B A A. Spud B. Holder NOTE: This range is equipped with 2 standard burners and 2 super burners. Spud size and location remain the same. 2 super burners. Spud size/location remain the same. A. Cap 6. Reinstall the cap. To Convert Sur
Résumé du contenu de la page N° 16
6. Place LP gas oven burner spud in plastic parts bag along To Convert Oven Burner with LP gas cooktop burner spuds for future use and keep with the bag containing literature. 1. Open the oven door and remove oven racks, oven tray, and 7. Reinstall oven burner. flame spreader and set aside. 8. Reinstall oven racks, oven tray and flame spreader. 2. Lift oven burner. The orifice spud is behind the oven burner air shutter. Complete Conversion 1. Refer to the “Make Gas Connection” section for pr
