Résumé du contenu de la page N° 1
INSTALLATION INSTRUCTIONS
30" (76.2 CM) FREESTANDING GAS RANGES
INSTRUCTIONS D’INSTALLATION DES CUISINIÈRES À GAZ
AUTOPORTANTES DE 30" (76,2 CM)
Table of Contents/Table des matières
RANGE SAFETY............................................................................. 2 SÉCURITÉ DE LA CUISINIÈRE...................................................20
INSTALLATION REQUIREMENTS ............................................... 4 EXIGENCES D’INSTALLATION..............................................
Résumé du contenu de la page N° 2
RANGE SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These words mean: You can be killed or seriously injured if you don't immediately DANG
Résumé du contenu de la page N° 3
In the State of Massachusetts, the following installation instructions apply: ■ Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by the State of Massachusetts. ■ If using a ball valve, it shall be a T-handle type. ■ A flexible gas connector, when used, must not exceed 3 feet. WARNING Tip Over Hazard A child or adult can tip the range and be killed. Connect anti-tip bracket to rear range foot. Reconnect the anti-tip
Résumé du contenu de la page N° 4
INSTALLATION REQUIREMENTS Tools and Parts Location Requirements Gather the required tools and parts before starting installation. IMPORTANT: Observe all governing codes and ordinances. Do Read and follow the instructions provided with any tools listed not obstruct flow of combustion and ventilation air. here. ■ It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The Tools needed model/serial rating plate is located behind th
Résumé du contenu de la page N° 5
Product Dimensions Cabinet Dimensions Cabinet opening dimensions shown are for 25" (64.0 cm) countertop depth, 24" (61.0 cm) base cabinet depth and 36" (91.4 cm) countertop height. IMPORTANT: If installing a range hood or microwave hood combination above the range, follow the range hood or microwave hood combination installation instructions for dimensional clearances above the cooktop surface. Range may be installed with zero clearance to combustible construction at the rear and on the si
Résumé du contenu de la page N° 6
Electrical Requirements Gas Supply Requirements WARNING WARNING Electrical Shock Hazard Explosion Hazard Plug into a grounded 3 prong outlet. Use a new CSA International approved gas supply line. Do not remove ground prong. Install a shut-off valve. Do not use an adapter. Securely tighten all gas connections. If connected to LP, have a qualified person make sure Do not use an extension cord. gas pressure does not exceed 14" (36 cm) water Failure to follow these instructions can result in death
Résumé du contenu de la page N° 7
Gas Supply Line Gas Pressure Regulator ■ Provide a gas supply line of ¾" (1.9 cm) rigid pipe to the The gas pressure regulator supplied with this range must be range location. A smaller size pipe on longer runs may result used. The inlet pressure to the regulator should be as follows for in insufficient gas supply. With LP gas, piping or tubing size proper operation: can be ½" (1.3 cm) minimum. Usually, LP gas suppliers Natural gas: determine the size and materials used in the system. Minimum
Résumé du contenu de la page N° 8
INSTALLATION INSTRUCTIONS Unpack Range Adjust Leveling Legs 1. If range height adjustment is necessary, use a wrench or pliers to loosen the 4 leveling legs. WARNING This may be done with the range on its back or with the range supported on 2 legs after the range has been placed back to Excessive Weight Hazard a standing position. Use two or more people to move and install range. NOTE: To place range back up into a standing position, put a Failure to do so can result in back or other injury.
Résumé du contenu de la page N° 9
Wall Mounting Install Anti-Tip Bracket 1. Remove the anti-tip bracket that is taped in the storage drawer. 2. Determine which mounting method to use: floor or wall. A If you have a stone or masonry floor you can use the wall B mounting method. 3. Determine and mark the edge of the range in the cutout space. The mounting bracket can be installed on either the left side or right side of the cutout. Position mounting bracket in cutout so that right (or left) edge of the bracket is ⁹⁄₁₆" (14.5
Résumé du contenu de la page N° 10
3. Use a ¹⁵⁄₁₆" combination wrench and an adjustable wrench to If burner caps are not properly positioned, surface burners attach the flexible connector to the adapters. Check that will not light. Place burner grates over burners and caps. connector is not kinked. A WARNING B C D E Electrical Shock Hazard Plug into a grounded 3 prong outlet. H G F Do not remove ground prong. A. Gas pressure regulator E. Manual gas shutoff valve B. Use pipe-joint compound. F. ½" or ¾" gas pipe Do not use an
Résumé du contenu de la page N° 11
Electronic Ignition System 2. Remove the control knob. Initial lighting and gas flame adjustments Cooktop and oven burners use pilotless igniters in place of Hold the knob stem in the low position using a pair of pliers. standing pilots. When the cooktop control knob is turned to the Use an ¹⁄₈" (3.0 mm) flat-blade screwdriver to turn the screw “LITE” position, the system creates a spark to light the burner. located in the center of the control knob stem until the flame This sparking conti
Résumé du contenu de la page N° 12
3. If the oven bake flame needs to be adjusted, locate the air shutter near the center rear of the storage drawer Replace Oven Racks and Storage Drawer compartment. Use a flat-blade screwdriver to loosen the air Replace oven racks in oven cavity. Replace storage drawer. shutter adjustment screw. Rotate the air shutter until the proper flame appears. Tighten air shutter adjustment screw. To Replace Storage Drawer: A 1. Fit the ends of the drawer glides into the rails in the range. B 2. Lift
Résumé du contenu de la page N° 13
GAS CONVERSIONS Gas conversions from Natural gas to LP gas or from LP gas to Natural gas must be done by a qualified installer. To Convert Gas Pressure Regulator 1. Remove oven racks from inside the oven cavity. WARNING 2. Remove the storage drawer. See “Replace Oven Racks and Storage Drawer” section. 3. Remove the oven door. See “Oven Door” section in the Use and Care Guide for oven door removal instructions. 4. Using a Phillips screwdriver, remove and set aside the 2 oven bake burner cover
Résumé du contenu de la page N° 14
46 .049 9. Unscrew the regulator cap and remove the plastic cover. 3. Install the Number .049 LP gas bake burner orifice hood, turning it clockwise 4 or 5 turns. Do not overtighten. A A B A. Plastic cover B. Regulator cap A. Number .049 LP orifice hood 10. Flip the regulator cap over and replace the plastic cover. 4. Position the bake burner over the bake burner orifice hood and reinstall using 3 screws. B C A A B A. Natural gas position B. LP gas position C. Plastic cover 11. Screw the regula
Résumé du contenu de la page N° 15
3. Turn the 1.65 mm Natural gas broil burner orifice hood counterclockwise to remove. To Convert Surface Burners 1. If installed, remove the burner grates. 2. Remove the burner caps. 3. Using a Phillips screwdriver, remove the burner base. A C A B D A. 1.65 mm Natural gas broil burner orifice hood 4. Install the Number 57 LP gas broil burner orifice hood, turning it clockwise 4 or 5 turns. Do not overtighten. A. Burner cap B. Gas tube opening C. Burner base screws 57 A D. Burner base 4. Apply
Résumé du contenu de la page N° 16
7. Replace burner cap. 4. Using a Phillips screwdriver, remove the 2 oven bake burner cover screws located at the rear of the oven. 8. Repeat steps 1 through 7 for the remaining burners. 9. Place Natural gas orifice spuds in plastic parts bag for future use and keep with the package containing literature. A 10. Replace burner grates. 11. Reinstall storage drawer. See the “Replace Oven Racks and B Storage Drawer” section for instructions. 12. Reinstall oven door. See the “Oven Door” section in
Résumé du contenu de la page N° 17
.049 46 10. Flip the regulator cap over and replace the plastic cover. 4. Position the bake burner over the bake burner orifice hood and reinstall using 3 screws. B C A A B A. LP gas position B. Natural gas position C. Plastic cover A. Bake burner 11. Screw the regulator cap securely back into place. Do not B. Bake burner orifice hood overtighten. 5. Reinstall the oven bake burner cover. To Convert Oven Bake Burner To Convert Oven Broil Burner 1. Locate the oven orifice hood from the front of
Résumé du contenu de la page N° 18
4. Install the Number 1.65 mm Natural gas broil burner orifice 4. Apply masking tape to the end of a ⁹⁄₃₂" (7.0 mm) nut driver to hood, turning it clockwise 4 or 5 turns. Do not overtighten. help hold the LP gas orifice spud in the nut driver while changing it. Press nut driver down onto the LP gas orifice spud and remove by turning it counterclockwise and lifting out. Set the LP gas orifice spud aside. 1.65 A A A. LP gas orifice spud Use the following chart for correct Natural gas orifice s
Résumé du contenu de la page N° 19
Notes 19
Résumé du contenu de la page N° 20
SÉCURITÉ DE LA CUISINIÈRE Votre sécurité et celle des autres est très importante. Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de toujours lire tous les messages de sécurité et de vous y conformer. Voici le symbole d’alerte de sécurité. Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décès et de blessures graves à vous et à d’autres. Tous les messages de sécurité suivront le symbole d’alerte de sécur
