Résumé du contenu de la page N° 1
INSTALLATION INSTRUCTIONS
30" (76.2 CM), 36" (91.4 CM) AND 48" (121.9 CM)
®
PRO-STYLE GAS CONVECTION RANGES
for residential use only
INSTRUCTIONS D’INSTALLATION
CUISINIÈRES À CONVECTION -
®
À GAZ PRO-STYLE DE 30" (76,2 CM), 36" (91,4 CM)
ET 48" (121,9 CM)
pour utilisation résidentielle uniquement
Table of Contents/Table des matières
RANGE SAFETY..............................................................................2 SÉCURITÉ DE LA CUISINIÈRE .......................................
Résumé du contenu de la page N° 2
RANGE SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These words mean: You can be killed or seriously injured if you don't immediately DANG
Résumé du contenu de la page N° 3
WARNING Tip Over Hazard A child or adult can tip the range and be killed. Connect anti-tip bracket to wall behind range. Reconnect the anti-tip bracket, if the range is moved. Failure to follow these instructions can result in death or serious burns to children and adults. INSTALLATION REQUIREMENTS Tools and Parts Gather the required tools and parts before starting installation. ■ Burner bases and burner caps Read and follow the instructions provided with any tools listed ■ Griddle drip tray
Résumé du contenu de la page N° 4
Location Requirements IMPORTANT: Observe all governing codes and ordinances. Do not obstruct flow of combustion and ventilation air. Product Dimensions ■ It is the installer’s responsibility to comply with installation 30" (76.2 cm) models clearances specified on the model/serial rating plate. The model/serial rating plate is located under the console on the A right-hand side. ■ It is recommended that a 600 CFM or larger range hood be B installed above the range. ■ It is not recommended tha
Résumé du contenu de la page N° 5
48" (121.9 cm) models A C B ** D B F O*** J A E C F I G H E Gas installation I area J Electrical L N installation K area* D M A. Island trim B. 27¹⁄₈" (68.9 cm) depth with control panel, see NOTE* C. 35¾" (90.2 cm) cooktop height when setting on the wheels A. 18" (45.7 cm) upper cabinet to countertop D. 48" (121.9 cm) width B. 30" (76.2 cm) model: 30" (76.2 cm) min. upper cabinet width E. Model/serial rating plate location 36" (91.4 cm) model: 36" (91.4 cm) min. upper cabinet width 48" (121.9
Résumé du contenu de la page N° 6
Electrical Requirements Gas Supply Requirements WARNING WARNING Electrical Shock Hazard Explosion Hazard Plug into a grounded 3 prong outlet. Use a new CSA International approved gas supply line. Do not remove ground prong. Install a shut-off valve. Do not use an adapter. Securely tighten all gas connections. Do not use an extension cord. If connected to LP, have a qualified person make sure gas pressure does not exceed 14" (36 cm) water Failure to follow these instructions can result in death
Résumé du contenu de la page N° 7
Gas Supply Line Gas Pressure Regulator ■ Provide a gas supply line of ¾" (1.9 cm) rigid pipe to the The gas pressure regulator supplied with this range must be range location. A smaller size pipe on longer runs may result used. The inlet pressure to the regulator should be as follows for in insufficient gas supply. With LP gas, piping or tubing size proper operation: can be ½" (1.3 cm) minimum. Usually, LP gas suppliers Natural Gas: determine the size and materials used in the system. Minimum
Résumé du contenu de la page N° 8
INSTALLATION INSTRUCTIONS Unpack Range Install Anti-Tip Bracket WARNING WARNING Excessive Weight Hazard Use two or more people to move and install range. Failure to do so can result in back or other injury. 1. Remove shipping materials, tape and film from range. Keep shipping pallet under range. Remove oven racks, grates and parts package from inside oven. Tip Over Hazard 2. Remove screws from kick plate. A child or adult can tip the range and be killed. B Connect anti-tip bracket to rear ran
Résumé du contenu de la page N° 9
3. Drill two ¹⁄₈" (3.0 mm) holes that correspond to the bracket holes of the determined mounting method. See the following. Make Gas Connection Floor Mounting B WARNING A Explosion Hazard Use a new CSA International approved gas supply line. Install a shut-off valve. Securely tighten all gas connections. A. #12 x 1⁵⁄₈" screws B. Anti-tip bracket If connected to LP, have a qualified person make sure gas pressure does not exceed 14" (36 cm) water Wall Mounting column. Examples of a qualified
Résumé du contenu de la page N° 10
Complete Connection 1. Open the manual shutoff valve in the gas supply line. The Level Range valve is open when the handle is parallel to the gas pipe. NOTE: Range must be level for satisfactory baking performance. 1. Place rack in oven. A 2. Place level on rack and check levelness of the range, first B side to side; then front to back. A. Closed valve B. Open valve 2. Test all connections by brushing on an approved noncorrosive leak-detection solution. If bubbles appear, a leak is indicat
Résumé du contenu de la page N° 11
Electronic Ignition System Install Burner Bases and Burner Caps Flame Height Install the burner base, making sure the igniter electrode is The cooktop flame should be a steady blue flame approximately ¼" (0.64 cm) high. properly aligned with the base. Place burner caps on top of burner bases. If burner caps are not properly positioned, surface Dual Flame Burner burners will not light. A 20,000 Btu/h Ultra Power™ Dual-Flame Burner B A A. Incorrect A. Upper (simmer) flame B. Correct B. Lower f
Résumé du contenu de la page N° 12
8. Turn the control knob to LO and using a butane extension 19. Replace burner grates. lighter, light the burner. 20. Test the flame by turning the control from LO to HI, checking the flame at each setting. Reinstall Kick Plate 1. Align shoulder screw mounting holes with shoulder screws on range. 2. Push kick plate down against front of range until the top screw holes are aligned with the mounting holes on the front 9. Remove the control knob. of the range. 10. Use a ¹⁄₈" x 4¼" flat-blade
Résumé du contenu de la page N° 13
GAS CONVERSIONS IMPORTANT: Gas conversions from Natural gas to LP gas must be done by a qualified installer. To Convert Gas Pressure Regulator 1. Remove screws from kick plate. WARNING B A Explosion Hazard Use a new CSA International approved gas supply line. Install a shut-off valve. A. Kick plate Securely tighten all gas connections. B. Remove these screws. If connected to LP, have a qualified person make sure 2. Push up on kick plate to release plate from shoulder screws. gas pressure does
Résumé du contenu de la page N° 14
6. Turn over the gas pressure regulator cap and reinstall on the 3. Slide the bake burner cover to the right or left. regulator so that the hollow end faces out and the letters “LP” are visible. A 7. Tighten the gas pressure regulator cap by using a large flat- A. Bake burner cover blade screwdriver, turning the regulator cap clockwise. 8. Test the gas pressure regulator and gas supply line. 4. Lift up and remove oven bake burner cover and set aside. The regulator must be checked at a minimum 1
Résumé du contenu de la page N° 15
7. Lift up clip on the oven bake burner electrode bracket with a 9. Apply masking tape to the end of a 7 mm nut driver to help finger or flat-blade screwdriver. hold the gas orifice spud in the nut driver while changing it. Insert nut driver into the gas opening and press down onto B the gas orifice spud and remove by turning the gas orifice A spud counterclockwise and lifting out. Set gas orifice spud aside. A A. Oven bake burner electrode bracket B. Electrode bracket clip 8. Pull electrod
Résumé du contenu de la page N° 16
13. Replace oven bake burner electrode inside bracket. 2. Lower cover and slide to left or right to slide shoulder screws into the narrow ends of the notches and lock into place. B A A A. Bake burner cover To Convert Oven Broil Burner (30" [76.2 cm] and 36" [91.4 cm] models and the Right Oven Cavity on 48" [121.9 cm] models) A. Oven bake burner electrode B. Oven bake burner electrode bracket 1. Remove broil burner screw and set aside. 14. Reinstall the oven bake burner and oven bake burner sc
Résumé du contenu de la page N° 17
3. Apply masking tape to the end of a 7 mm nut driver to help 3. Slide the bake burner cover to the right or left. hold the gas orifice spud in the nut driver while changing it. Insert nut driver into the gas opening and press down onto the gas orifice spud and remove by turning the gas orifice spud counterclockwise and lifting out. Set gas orifice spud aside. A A. Bake burner cover 4. Lift up and remove oven bake burner cover and set aside. 5. Remove the oven bake burner screws and oven bak
Résumé du contenu de la page N° 18
7. Pull electrode out of bracket. 11. Push down on the clip on the electrode bracket. B A A B A. Grasp electrode here. A. Oven bake burner electrode bracket B. Bracket B. Electrode bracket clip 8. Apply masking tape to the end of a 7 mm nut driver to help 12. Replace oven bake burner electrode inside bracket. hold the gas orifice spud in the nut driver while changing it. Insert nut driver into the gas opening and press down onto B the gas orifice spud and remove by turning the gas orifice sp
Résumé du contenu de la page N° 19
4. Apply masking tape to the end of a 7 mm nut driver to help Replace Oven Bake Burner Cover hold the gas orifice spud in the nut driver while changing it. 1. Align rear shoulder screw mounting holes (keyholes) on the Insert nut driver into the gas opening and press down onto oven bake burner cover with shoulder screws in the bottom the gas orifice spud and remove by turning the gas orifice of the oven. spud counterclockwise and lifting out. Set gas orifice spud aside. 5. Replace with cor
Résumé du contenu de la page N° 20
12. Open the oven door and remove the 2 screws on each side of 17. Lift up on the control console and set it back into place. For a the range that hold the control console in place. proper fit, the flange of the control console must hook over the lip on the front of the range cooktop. A B NOTE: Make sure to leave oven door open or the control A. Control console flange console will not rest in the side brackets properly once it is B. Front lip of range cooktop detached. 13. Pull up on the co
